Sasem OnAir USB HDTV User manual
If any problem happens in using OnAir
USB HDTV,
Phone : 031-9786-333
FAX : 031-9788-584
URL : www.sasem.com, www.onairtv.co.kr
E-mail : supports@sasem.com
Copyright
Each involving company copyrights the software
and the firmware in this manual.
Every software and firmware is protected under
the intellectual property right and treaty,
computer program preservation and copyright law
and international copyright convention.
You cannot copy and excerpt this manual without
permission.
Warrenty : 1 year
ⓒ2003-2004 Sasem Co., Ltd. All right reserved.
Made in Korea.
INFORMATION TO THE USER (Part 15.105(b))
INFORMATION TO THE USER
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
WARNING (Part 15.21)
The manufacturer is not responsible for any Radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to
operate the equipment.”
Contents
1 Introduction ..................................................... 6
1.1 Specification ......................................................................... 6
1.2 Package Included ................................................................8
1.3 System Requirement .......................................................... 9
2 Installation ..................................................... 10
2.1 Installation Checklist .........................................................10
2.2 Hardware Installation ........................................................11
2.3 OnAir USB HDTV Device Driver Installation..................11
2.4 OnAir USB HDTV Application Software Installation .....14
6 OnAir USB HDTV Manual
1Introduction
1.1 Specification
Digital & Analog TV
Full HDTV of 1920 X 1080 (ATSC)
Digital (ATSC) HDTV / Analog (NTSC) TV
AC3 / AAC Audio Decoding output
Recording & Playback
Real-time or Schedule Recording
Still Capture (JPEG or BMP File)
Hardware MPEG2 Encoding for Analog Video Source (easy to
create own DVD title via DVD-RW and tool) : Resolution 720
x 480
Playback HD Stream File format (ATSC and Japan BS)
Playback Analog TV File (MPEG2 DVD Stream : Resolution
720 x 480 )
Playback of HD Stream files (Random access)
Time-Shifting*
Real-time playback of D-VHS (Windows XP only)
Recording the HD stream files from PC into D-VHS (Windows
XP only)
Saving D-VHS streams into PC as stream files (Windows XP
only)
Provide OnAir HD Editor
External A/V Input & Output
External A/V Input (Video, Stereo Audio, S-Video , NTSC/PAL
Video )
SPDIF Output through sound card (will support AAC)
Bundle WinDVD4 Player (InterVideo, Inc.)
Suitable Features
Wall Paper TV View
Zoom-In
Various Aspect Ratios
1. Introduction 7
Individual Channel Color Adjustment
Digital Signal Strength Display
Sleep Timer
Remote Control (IR Model Only)
* Time-Shifting ? While playing live Analog TV, the time shifting offers
you ability to pause the live TV for pre-defined period of time. It
provides by recording Live TV in real-time for pre-defined period of time
while playing Live TV. It helps you to not miss any part of Live TV even
though you stay away from TV for a while.(Analog TV only)
8 OnAir USB HDTV Manual
1.2 Package Included
3.USB Cable
1.USB HDTV 2.Remote
Controller (AAA
Battery 2ea
included)
4.RF Antenna
Cable
5.InstallationC
D
6.Installation
Manual
7.Adapter
If something excluded, please contact with our Customer support
department. (+82-31-978-8660)
1. Introduction 9
1.3 System Requirement
USB 2.0 port supported Desktop PC or Notebook (PCI / PCMCIA
types of USB2.0)
OS : MS Windows XP Service Pack 1 or above, MS Windows XP
Media Center Edition (MCE 1.x)
DirectX 9.0
Minimum system requirement (with DXVA support)
ATI RADEON 7200 or
above
ATI Mobility Radeon
7500 or above
Nvidia Geforce MX 440 or
above
Nvidia Geforce 4 Go or
above
VGA
Video Memory 32MB or above
CPU PentiumIII 800 Mhz or
above
PentiumVI 1.6 Ghz or
above
Mem. 128MB (256MB Recommend)
Minimum system requirement (not recommended, without
DXVA support)
VGA : AGP4X with video memory 32MB or above
CPU : Pentium4 1.6Ghz or AMD Athlon XP
Memory : 128MB (256MB Recommend)
10 OnAir USB HDTV Manual
2Installation
2.1 Installation Checklist
2.1.1 Windows XP Service Pack 1 Installation
From the desktop menu of "My Computer", click the mouse’s right
button to open the “Properties". Then, find out what the current
operating system is running on your system. If your operation
system is not "Microsoft Windows XP Service Pack 1" then please
install the “Service Pack 1” from the Windows Update through the
internet
Please open Microsoft Internet Explorer, and choose the tool
menu on top of menu bar and click the “windows update” and run
the update scan. If the update scan is completed, there will be
update scan result displayed. From the update scan result list,
please install the Microsoft Windows XP Service Pack 1 from
"Critical Updates and Service Pack”.
2.1.2 USB2.0 Patch (HotFix)
Because the USB 2.0 is a new device, even Microsoft
Windows XP Service Pack 1 has a bug on the USB 2.0
Device Driver.
At first, please confirm the "Windows HotFix - KB822603"
is installed on your system from the “program add /
remove” under control panel. If your system already
installed this, your system had completed the patch of
USB2.0 Device Driver Bug. If your system did not have this,
please open Microsoft Internet Explorer, and choose the
tool menu on top of menu bar and click the “windows
update” and run the update scan. If the update scan is
completed, there will be a list of update scan result
displayed. From the list of update scan result, please find
the "Windows XP SP1 recommended update (KB822603)"
2. Installation 11
under Windows XP menu and install it on your system, or
please download the HotFix from following URL and install it on
your system.
http://www.microsoft.com/downloads/details.aspx?amp;amp;dis
playlang=en&familyid=733dd867-56a0-4956-b7fe-
e85b688b7f86&displaylang=en
This HotFix patch program is released by Microsoft to fix a
problem of failing recognition of USB 2.0 device.
2.2 Hardware Installation
OnAir USB HDTV is an external HDTV device that connected with
personal computer or notebooks via USB2.0 port.
Please plug in the power adaptor into hardware, and connect with
personal computers or notebooks via USB cable.
2.3 OnAir USB HDTV Device Driver Installation
Please insert the provided installation CD into your system’s CD-
ROM drive. The installation CD will automatically start the
installation. From the displayed product list, select the driver
installation under OnAir USB HDTV.
If the installation CD does not auto-run, please open window
explorer to find the “installer.exe” file and execute the file.
12 OnAir USB HDTV Manual
2.3.1 OnAir USB HDTV Device Driver Installation for
Windows XP
1. This is a dialog box of
choosing a language of
installation program.
Please choose one of
languages of either
English or Korean, and
press [OK] button to
continue.
2. This is a dialog box of the
warning notice to users
that the driver may not
be installed if the OnAir
USB HDTV is connected
to the system. If the
OnAir USB HDTV is
connected to your
system’s USB port, please
remove it first and then
click [Next] button to
continue.
3. Please close all other
windows application
programs before running
the installation, and click
the [Next] button to
continue.
2. Installation 13
4. If you are ready to run
the installation program,
please click the [Next]
button to continue.
5. The OnAir USB HDTV
device driver installation
is completed. Please
click the [Finish] button,
and plug in the OnAir
USB HDTV device into
your system via USB2.0..
14 OnAir USB HDTV Manual
2.4 OnAir USB HDTV Application Software
Installation
The OnAir USB HDTV application software installation is provided
based on application software version 2.2.
The given installation CD with package includes the application
software of OnAir USB HDTV.
Please insert the provided installation CD into your system’s CD-
ROM drive. The installation CD will automatically start the
installation. From the displayed product list, please select the
application software under OnAir USB HDTV.
If the installation CD does not auto-run, please open window
explorer and choose the “installer.exe” file to execute the
installation.
1. The installation wizard of
OnAir USB HDTV will guide
you to install the
application software. To
continue the installation,
please click [Next] button.
2. Please choose a destination
folder location to install the
software. If you would
like to choose different
folder location, please click
[Browse] button and
choose another folder
location. Please click the
[Next] button to continue.
2. Installation 15
3. It is a dialog box of adding
remote control program
into “Start Program”. For
your convenience, we
recommend you to add the
program in “Start Program”
by clicking “Yes” button.
4. It is a dialog box of adding
Scheduler program into
“Start Program”. For your
convenience, we
recommend you to add the
program in “Start Program”
by clicking “Yes” button.
5. It is a dialog box of adding
the OnAir USB HDTV
application software icons
to the “desktop” as short-
cut icons. For your
convenience, we
recommend you to add
short-cut icons to the
desktop by clicking “Yes”
button.
6. The OnAir USB HDTV
application software is
successfully installed.
To complete the installation
process, please reboot your
system. Please click the
“Yes” button to reboot your
system now or click “No”
button to reboot system
later. Please click the
[Finish] button to complete
the installation.
Table of contents
