Satel Versa User manual

int-tsh_ov_en 10/15
Keypad
INT-TSH
Firmware version 1.00
VERSA • VERSA Plus • VERSA IP
Brief System User Manual
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.eu

WARNINGS
Please read this manual carefully before use.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
Warning
This is a Class A product. In a domestic environment this product may cause radio frequency
interference in which case the user may be required to take adequate measures.
The installer manual contains information on how to minimize the radio interference.
SATEL's goal is to continually upgrade the quality of its products, which may result in
alterations of their technical specifications and firmware. The current information on
the introduced modifications is available on our website.
Please visit us:
http://www.satel.eu
The declaration of conformity may be consulted at www.satel.eu/ce
The following symbol may be used in this manual:
- note.

We are pleased that you have chosen a product offered by us. We wish you satisfaction with
your choice and would like to assure you that we are always ready to provide professional
assistance and information on our products.
SATEL Ltd. is a manufacturer of a wide variety of dedicated devices for use in alarm
systems. Additional information can be found on our website www.satel.eu or at points of
sale offering our products.
1. Keypad description
The touch screen displays information about the system status, while allowing you to operate
and program the alarm system, as well as control the home automation equipment. Intuitive
icon-based menu makes the everyday use easier. On most screens, the keypad offers two
operating modes:
graphical mode – large icons are displayed without description,
verbose mode – small icons are displayed with description.
To change the operating mode, use the following icons:
– tap to switch over the screen to the verbose mode,
– tap to switch over the screen to the graphical mode.
This manual describes how to operate the keypad, based on the graphical mode.
Tapping an icon or icon description will display the next screen or start the specified function.
The icon will bring you back to the previous screen. Tapping the icon will display the
main screen.
After the keypad is idle for 10 minutes, the screen can either go blank, or a slide show or the
clock can be displayed.
Tapping the screen when it is blank or the screen saver is displayed will wake up the keypad.
The keypad can also be woken up e.g. on opening the door, detecting motion by a detector

2 INT-TSH SATEL
etc. The installer defines the content which is to be displayed after the keypad wake-up
(status screen, main screen or start of the disarming procedure).
Tapping and holding the screen for 3 seconds will trigger a silent panic alarm, if:
a slide show, clock or status screen is displayed,
the screen is blank.
Whether this function is to be available should be defined by the installer.
During the keypad inactivity period, messages about arming/disarming, entry/exit delay
countdown, alarm etc. can be displayed on the screen.
1.1.1 Status bar
When a slide show, clock or status screen is displayed, the status bar is shown at the top of
the screen. Icons situated on the status bar indicate the system status.
Icon Color System status
green exit delay countdown is running in partition 1 / partition 1 is armed
red alarm or alarm memory in partition 1
green exit delay countdown is running in partition 2 / partition 2 is armed
red alarm or alarm memory in partition 2
yellow trouble or trouble memory
blue service mode entered
The information about arming may be hidden after the time defined by the installer has
elapsed.
If the G RADE 2 option is enabled by the installer:
information about the alarm is not presented;
the icon indicates trouble / trouble memory / alarm / alarm memory / bypassed
zones.
1.1.2 Slide show
The slide show can be displayed as the status screen background or the screensaver. The
pictures to be displayed should be saved to a microSD memory card, which will be put into
the keypad by the installer. The installer defines the speed at which the pictures will change
during the slide show.
1.1.3 Status screen
The status screen is displayed 60 seconds after the last operation performed on the keypad
screen, unless the terminal is running (see p. 13). When the terminal is displayed, the status
screen may appear later or even not appear at all (e.g. when the service menu is open).
If the user is logged in, he/she will be automatically logged out a few seconds after the
status screen is displayed.

SATEL INT-TSH 3
Additional information presented on the status screen
The keypad with factory settings presents the date and time on the status screen. The
installer can customize the information displayed to suit the user needs. Information on the
state of selected partitions, zones or outputs, date and time, as well as any text, can be
presented on the status screen.
Icons illustrating the state of partitions are described in section “Partition status” (p. 8).
Icons illustrating the state of zones are described in section “Zone status” (p. 9).
Icons illustrating the state of outputs are shown in the table below.
Icon Color Output status
grey deactivated
red activated
Additional messages, connected with occurrence of specific events (e.g. arming or disarming,
auto-arming delay countdown, entry / exit delay countdown, alarm, etc.), may also appear on
the status screen.
Functions available from the status screen
Tapping the status screen will display the main screen. If at least one partition operated from
the keypad is armed and the keypad has not been used for at least 10 minutes, the
authorization screen can be displayed. Enter the code to be able to disarm the partition.
Status screen background
A single picture or a slide show can be displayed as the status screen. The status screen
background is to be configured by the installer.

4 INT-TSH SATEL
1.1.4 Main screen
Presented on the main screen are:
date and time in the format defined by the installer (if some specific events occur, other
messages can be displayed, instead of the date and time, e.g. entry or exit delay
countdown, alarm messages, etc.);
name of the currently logged user;
icons enabling operation of the keypad and alarm system.
Icon Function
Informs you that no user is logged in.
User login.
Informs you that a user is logged in (name of the currently logged user is
displayed below).
User logout.
Displays the “Arming” screen (see pages 5and 14). The keypad distinguishes
between tapping the icon and tapping and holding the icon for 3 seconds. After
tapping the icon, quick arming, i.e. without entering the code, may be available
(consult this with the installer). Tapping and holding the icon will always display
the authorization screen, and the ”Arming” screen will only be displayed after
entering the code.
Enables disarming / alarm clearing (see pages 7, 16 and 17).
Displays the “Control” screen (see p. 7).
Displays the “System status” screen (see p. 8).
Displays the “Emergency” screen (see p. 10).
Displays the “Advanced” screen (see p. 11).

SATEL INT-TSH 5
1.1.5 Authorization screen
Some screens and functions may only be available after user authorization. The authorization
is code based. Use the number keys to enter the code and then confirm, tapping the
icon.
By default, the following codes are preprogrammed in the control panel:
service code: 12345
user 30 code: 1111
If you make a mistake when entering the code, tap and re-enter the code (if you fail to
enter the valid code within one minute, information on entering a wrong code will be saved to
the control panel memory).
1.1.6 “Arming” screen
Appearance of the screen changes depending on whether you are allowed to arm one or two
partitions.
Icon Function
Arming in the full mode.
Arming in the day mode.
Arming in the night mode.

6 INT-TSH SATEL
Screen with partition selection
This screen is displayed when you can arm both partitions. The partitions are presented by
means of appropriately described fields. By default, the icon is displayed in both fields,
which means that the partition is to be armed. Tap on the field, if the partition is not to be
armed (the icon will be displayed). Having defined where the system is to be armed, tap
one of the icons to arm the system.
Screen without partition selection
This screen is displayed when you can arm one partition only (also when the quick arming is
allowed by the installer in one partition only).

SATEL INT-TSH 7
1.1.7 “Alarm clearing / Disarming” screen
The “Alarm clearing / Disarming” screen will be displayed after you tap the icon on
the main screen, when there is an alarm (alarm memory) and at least one partition is armed.
Icon Function
Enables alarm clearing.
Enables disarming.
1.1.8 “Control” screen
The icons on the screen show the outputs you are allowed to control. Tapping an icon
changes the output status. The icons illustrating the status of outputs are described on p. 3.

8 INT-TSH SATEL
1.1.9 “System status” screen
Icon Function
Displays the “Partition status” screen.
Displays the “Zone status” screen.
Displays the “Troubles” screen, on which the current troubles are presented
(the installer can configure the control panel to display the troubles until
cleared).
Enables viewing the event log.
When viewing the log of events, the icon is available at the top of the screen.
Tapping the icon will toggle the information presentation mode: light grey / color font
(and the other way round).
Partition status
The status of partitions is illustrated by means of icons. Tap the icon situated at the top of
the screen to see description of all icons. The number shown next to the icon corresponds to
the partition number. On tapping the icon, the full partition name will be presented at the
display bottom.
Icon Partition status
disarmed – there are no violated zones
exit delay countdown is running – remaining time longer than 10 seconds
exit delay countdown is running – less than 10 seconds remained