SATION SATION-PM1304.212X User manual

KNX Push Button Panel User Manual
----------------------------------------------------------------------------------------------------------------------------------------------
Zhuhai Sation Technology Co., Ltd | www.sation.com.cn
3F-2,Building B1, No.1 Software Road, Zhuhai Hi-tech Zone, Zhuhai, Guangdong, China 519000
Copyright Clarify
Copyright ownership belongs to Zhuhai Sation Technology
Co., Ltd. shall not be reproduced, copied, or used in other
ways without permission. Otherwise Zhuhai Sation
Technology Co., Ltd. will have the right to pursue legal
responsibilities.
Version
Notice
1. Please read this user manual carefully before using the product.
2. This product is used in indoor environment and installed in
electrical control box.
3. Please install this product in a dry and ventilated place.
4. Before power on, please confirm the input voltage according to
the manual; after power on, please confirm the normal output
Voltage before connecting to the control bus.
5. Please make sure the secure shell is in good condition, if the
shell is damaged, please stop using to avoid accident.
6. This product is NOT a toy, please make sure it is out of children
touch.
7. Only be suitable for EIB/KNX system bus.
8. Others:
The below sign indicates this product can’t be dealt as ordinary
family rubbish, in order to avoid the possible environment and
human health harm caused by the electrical waste, this product
must follow recovery processing. Please contact the local
recycling department after this product is scrapped, to make
sure it can go as the right waste processing procedure.
The user manual refer to the
following devices：
SATION-PM1304.212X
SATION-PM1304.112X
SATION-PM1308.212X
SATION-PM1308.112X
Version Release Date Remark
V1.0 March 1st ,2020 1st Release
V1.1 March 1st ,2023 2rd Release

KNX Push Button Panel User Manual
----------------------------------------------------------------------------------------------------------------------------------------------
Zhuhai Sation Technology Co., Ltd | www.sation.com.cn
3F-2,Building B1, No.1 Software Road, Zhuhai Hi-tech Zone, Zhuhai, Guangdong, China 519000
1. Function Overview
This product can be used to control the following devices:
1) Switch actuator
2) Curtain actuator
3) Dimming actuator
4) Various Other KNX devices
This product can work in the following two modes
Combined with input function
1) Dimming: one dimming up and the other to dimming down
2) Curtain control: one Open/close and the other stop
3) Switch function: one ON and the other to OFF
independent input function
1) Switch function: edge control, edge flip, state sending, fixed
value sending, long and short input control
2) Scene function: configure scene
3) One-key dimming: short input switch, long input dimming
4) One-click curtain: Customize long input to move (or stop), short
input to stop (or move)
Above two modes support object blocking, object and/or logic
operations, and device power-on behavior configuration.
LED function configuration:
Each button side corresponds to an orange and white LED
indicator; The LED indicator can be freely defined as external
parameter indication, internal parameter indication and key state
indication.
Use the engineering debugging tool software ETS for system
debugging.
2. Product Introduce
Color Options

KNX Push Button Panel User Manual
----------------------------------------------------------------------------------------------------------------------------------------------
Zhuhai Sation Technology Co., Ltd | www.sation.com.cn
3F-2,Building B1, No.1 Software Road, Zhuhai Hi-tech Zone, Zhuhai, Guangdong, China 519000
3. Progamming Mode
1) S1~S8 correspond to keys 1~8.
2) L1~L8 of PM1308.112X and PM1308.212X correspond to the
indicator light of button 1 ~ the indicator light of button 8, each
button indicator has two colors of orange and white to match.
3) Press S1, S3, S6, S8 at the same time to enter the programming
mode, and press S1, S3, S6, S8 again to exit the programming mode.
The L1, L3, L6, L8 of PM1308.112X and PM1308.212X light up
orange LEDs at the same time
4) The panel is fixed by two mounting buckles.
5) PM1308.212X does not need auxiliary power input, no yellow
and white terminals.
4. Installation
1) Fix the mounting bracket in
the 86 bottom box with
mounting screws
2) Connect KNX bus and
auxiliary power according to
the logo (limited to
PM1308.112X)
3) Push the panel until the
mounting buckle locks the
mounting bracket