Savant PWM-PENC3-00 User manual

http://dealers.savantav.com/
portal/redirector.php?id=1200
Savant® Low Voltage Power Module Enclosure (PWM-PENC3-00)
Quick Reference Guide
PWM-PENC3-00 Quick Reference Guide | 009-1546-03 1 of 2 45 Perseverance Way, Hyannis MA 02601
Copyright © 2020 Savant Systems, LLC | 200226 Savant.com | 508.683.2500
Front View
–SKL-3040-00 - 40 Keypad Power and Control Module
–SHA-PMOD5-00 - 5 Shade Power Module with RS485
Distribution
–SHA-PMOD5G-00 - 5 Shade Power Module With Serial
Distribution
For product-specific requirements and deployment steps, refer to
the product's documentation on the Savant Community.
AThe PWM-PENC3-xx enclosure supports one, two, or
three power modules. The modules are not included with
the enclosure and need to be purchased separately.
B
Three ½inch electrical knockouts. Prior to installing the
power module(s), remove the knockout associated with
the module being installed and snap in the ½ inch nylon
bushing supplied with each power module.
NOTE: Savant recommends installing the / inch bushing
supplied with each power module to reduce the
chances of chafing wires on the metal enclosure.
C
AC Compartment cover. To remove the cover, turn the
captive panel screw counterclockwise (CCW) until the
screw pops up and out of the threaded insert. Slide cover
up and then out away from the enclosure.
DElectrical knockouts (inch) for supplying power from a
breaker panel or similar. Remove appropriate knockout(s)
and install a cable clamp.
(1) Enclosure (PWM-PENC3-xx)
(1) Enclosure Cover with Handles (093-3046-xx)
(4) M4 x 6mm Phillips - Front Cover Screws (039-0383-xx)
(2) WAGO 6-Position Push Connector (028-0815-xx)
(1) Product Regulatory Statement (009-1853-xx)
Box Contents
Specifications
Additional Required Items
Minimum Supported Release
Savant OS da Vinci 8.5
Regulatory
RoHS Compliant
C
B
D
A
Dimensions and Weights
Height Width Depth Weight
Enclosure 18 in
(45.72 cm)
14.25 in
(36.20 cm)
3.5 in
(8.89 cm)
10.5 lbs
(4.76 kg)
Enclosure
with Cover
19 in
(48.26 cm)
15.25 in
(38.74 cm)
4.72 in
(11.99 cm)
15.5 lbs
(7.05 kg)
Shipping 21.0 in
(53.34 cm)
17.0 in
(43.18 cm)
5.0 in
(12.7 cm)
16 lbs
(7.26 kg)
The PWM-PENC3 includes an enclosure, cover, and connectors.
In addition to these items, at least one Savant power module is
required. Supported power modules include:
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity
(non-condensing)

PWM-PENC3-00 Quick Reference Guide | 009-1546-03 2 of 2 45 Perseverance Way, Hyannis MA 02601
Copyright © 2020 Savant Systems, LLC | 200226 Savant.com | 508.683.2500
The enclosure can be surface mounted, or in-wall mounted between two studs. These methods are described below.
1. Loosen the four hold down screws that secure the lid to the
enclosure.
2. Push up on the lid and pull away from the enclosure. Set lid
aside.
3. Place the panel on wall where it will be mounted and make
a mark on the wall for each of the mounting holes in the
enclosure. Refer to image below.
4. Drill a starter hole for each screw location. Secure the
enclosure to wall using (6) #8 x 1 inch self tapping screws
into a solid sub wall. If the surface the panel is being mounted
to is drywall with no solid surface behind it, sturdy wall anchors
that can hold a minimum of 50 lbs ( 22.7 kg) is sucient.
5. Screw the panel to the wall and ensure it is securely mounted.
1. Loosen the four hold down screws that secure the lid to the
enclosure.
2. Push up on the lid and pull away from the enclosure. Set lid
aside.
3. Locate two adjacent studs that are 16-inch on center. If there is
drywall installed, cut drywall to the dimensions shown in image.
WALL CUTOUT
in.
18 in.
14
1/2
4. Secure the power panel enclosure between the studs using
appropriately sized #6 self tapping screws. Screw to studs
using the three holes positioned toward the front of the panel.
Using the holes closest to front panel allows access to the
screws when the power modules are installed. See image
below.
Enclosure Installation
Surface Mount Instructions In-Wall Mount Instructions
Shades:
–Five Shade Module with RS-485 Distribution QRG (009-1547-xx)
(SHA-PMOD5-xx)
–Five Shade Module with Serial Distribution QRG (009-1844-xx)
(SHA-PMOD5G-xx)
–Shades Installation and Wiring Guide (009-1532-xx)
(SHA-PMOD5 Power Supply, SHA-M24V485-xx Somfy Motors)
–J Geiger Wired Shades Installation Guide (009-1847-xx)
(SHA-PMOD5G, Power Supply, SHA-MGEIG200-xx J Geiger
Motors - da Vinci 9.1 and higher)
–Shades Provisioning and Programming Guide (009-1525-xx)
ECHO Style Keypad Low Voltage Lighting:
–40-Keypad Power and Control Module QRG (009-1796-xx)
(SKL-3040-00 Power Supply)
–Low-Voltage Keypad Deployment Guide (009-1731-xx)
For more information, the documents listed below are available on
the Savant Customer Community and Savant Store.
Additional Information
Mounting Holes
for Studs
Front Panel
#8 x 1 / inch