Savant SPK-S1WS Series User manual

SPK-S1WSx-xx Quick Reference Guide | 009-1886-02 1 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2021 Savant Systems, Inc. | 210118 Savant.com | 508.683.2500
Minimum Support Requirements
Software
Release da Vinci 9.2
Regulatory
Safety and
Emissions
FCC Part 15B C Tick UL CE
RoHS Compliant
Box Contents
(1) Smart Audio WiSA Sub 1 (SPK-S1WSx-xx)
(2) 2-Pin Screw Down Connector (028-0884-xx)
(1) Power Cord (064-0480-xx)
(1) Pair of White Gloves
(1) Product Regulatory Statement (009-1950-xx)
Specifications
Input Panel (Bottom)
AC 100-120V -50/60Hz
220-240V
200W
Min Max
Volume
60
LPF Phase
Trigger
In
IR
In
LPF
12dB/24dB
Power
Mode
Status Wisa
ResetLFE In
On Audio Sense Trigger
160 Hz 0 180
-50/60Hz
Caution: Risk of Electric
Shock - Do Not Open For Indoor
Use Only
E475835
AV Equipment
!
0981 !
Assembled in China Attention: Risque
D’Electocution - No Pas Ouvir!
Achtung: Gefahr Eines Elektr
Schlages - Nicht Önen!
ABC D E F G HIJKL
AAC Power
Input
Main power input.
BVolume
Control
Adjusts volume.
CLow Pass
Filter
Adjusts the upper end of frequency
response.
DPhase Control Used to time-align the output signal from
the WiSA Sub to other speakers.
E12V Trigger
Input
2-pin screw down connector. Used to
control ON/STANDBY settings based on
12V DC input signal.
FIR Input 2-pin screw down connector allowing for
IR control.
GLPF Slope Controls the slope rate upper end
frequency response.
HPower Mode On: Device is always powered on.
Audio Sense: Power command sent with
active audio signal.
Trigger: Powers on with 12V Trigger Input.
ILFE Input RCA used for LFE input.
JStatus LED O: Resetting, or is powered up and
booting the embedded firmware.
Green Fast Blinking: Updating.
Green Slow Blinking: Entering or finishing
an update.
Green: Normal operation.
Orange: Critical system error.
Orange Slow Blink: Standby power mode.
KReset button Hold for 10 seconds to disconnect
speaker from the network and forget any
associated WiSA devices.
Note: This will place the speaker in
Associate Mode.
LWiSA LED O: Forced Analog Mode.
Green Fast Blinking: Ready to pair.
Green Slow Blinking: Streaming audio.
Green: WiSA connected.
Orange: Audio is muted.
Orange Slow Blinking: WiSA module reset.
Orange Fast Blinking: Reconnecting.
Savant® Smart Audio WiSA Sub 1 Quick Reference Guide
WiSA
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions (with Grill)
Height Width Depth
SPK-S1WSx 8.0 in
(20.4 cm)
7.5 in
(19.16 cm)
9.1 in
(23.0 cm)
Shipping 14.0 in
(35.56 cm)
14.0 in
(35.56 cm)
13.0 in
(33.02 cm)
Weight
Shipping Weight 18.3 lb (8.3 kg)
Net Weight 15.2 lb (6.9 kg)
Power
Input Power 100 - 120V AC (50/60Hz)
220 - 240V (50/60HZ)
Standby Power
Consumption
WiSA input: 2.5 W
Analog input: 1.25 W
Operating Parameters
Low Pass Filter 60 - 160 Hz
Low Pass Filter
Slope 12 / 24 dB/octave
Frequency
Range 30hz - 160 hz +/- 0.5 dB
Wattage 200 Watts
Streaming Quality Up to 24 bit / 96kHz High Resolution Audio

SPK-S1WSx-xx Quick Reference Guide | 009-1886-02 2 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2021 Savant Systems, Inc. | 210118 Savant.com | 508.683.2500
Connect Power
The IP Audio Products have an AC Power connection.
Make the appropriate power connections before attempting discovery within the Savant Pro App.
Associate Mode
Associate Mode indicates the WiSA Sub is not paired with any WiSA transmitting device. To enter this mode, hold the reset button for 10
seconds.
For more information on WISA setup process, see the Smart Audio WISA Setup Guide (009-1903-xx) on the Savant Community.
Auto Switch Mode
The default mode for the Smart Audio WiSA Sub 1.
In this mode, the WiSA Sub will switch between WiSA and analog inputs as needed. To enter this mode, press the reset button until the WiSA
LED turns green. This mode will remain active through reboots.
–Both the WiSA and the LFE input are active.
–If a WiSA device is connected, input will automatically switch to WiSA.
–If the WiSA LED transitions to Standby/Reset or Pairing, input will switch back to analog.
–If the user presses and holds reset button, input will be switched to WiSA so that a test tone can be heard.
Forced Analog Mode
The analog-input only mode for the Smart Audio WiSA Sub 1.
To enter Forced Analog Mode, toggle the LFP slope switch 4 times within 10 seconds. This mode will remain active through reboots.
–The LFE input will always be active, and WiSA output will not be active.
–The WiSA LED will be turned o to indicate this mode.
–Press and hold the reset button to place the unit back in Auto Switch mode.
NOTE:
The WiSA logo, WiSA, WiSA Ready, and WiSA Certified are trademarks or certification marks of WiSA LLC. Third-party trade names, trademarks
and product names are the intellectual property of their respective owners.