Savch SPN-070S User manual

三碁 SPN-070S/SPN-101S使用说明
一、型号确认
每台 SAVCH HMI 在出厂前均做过功能测试,客户于产品送达拆封后,请执行下列检查步骤:
检查内部是否含有 SAVCH HMI 本体,随机手册一本。
产品的机种型号是否符合您所订购之型号。
产品是否因运送不慎造成损坏,若有损坏请勿接入电源。
当您发现有上述问题时请立即通知 SAVCH 电气各区业务人员。
二、注意事项及安装步骤
注意事项:·严格按照端子上的标注的电源极性接线,否则会造成产品故障或者烧毁。
·产品与底部其他部件,必须保持足够的空间,以避免散热不良造成的设备损坏。
安装步骤:·将HMI 装入开孔面板内,将侧边的 4个卡扣与安装面板锁紧。
三、型号说明
HMI型号
电源规格
Human Machine Interface
Model:
Power:DC24V 0.45A
P/N:1605261053011810012
SPN-070S
SAVCH ELECTRIC CO.,LTD.
产品名称
S PN – 070S W
显示屏尺寸:
070:7英寸
101:10.1英寸
SAVCH W:支持Wifi
G:支持4G
无:通用机
四、部件与开孔尺寸
SPN-070S
SPN-101S
SPN-070S开孔尺寸 SPN-101S开孔尺寸
五、接口定义
COM1 接口定义
COM2 接口定义
Pin
定义
Pin
定义
Pin
定义
Pin
定义
1
RS422 TX+/RS485 A+
2
RS232 RXD
1
RS232 RXD
2
RS232 TXD
3
RS232 TXD
4
CANL
3
GND
4
RS485 B-
5
GND
6
RS422 TX-/RS485 B-
5
RS485 A+
7
CANH
8
RS422 RX-
9
RS422 RX+
六、产品规格
型号
项目
SPN-070S SPN-101S
电源
输入电源
DC24V±20%
DC24V±20%
功耗 5W 9W
电源隔离 内置 内置
耐电压 AC 500V AC 500V
绝缘阻抗 超过 500MΩ@500VDC 超过 500MΩ@500VDC
耐振动 10~25HZ (X、Y、Z轴向 2G/30 分钟) 10~25HZ (X、Y、Z轴向 2G/30 分钟)
冷却
方式
冷却方式
自然风冷却
自然风冷却
防护等级 IP65 IP65
存储环境温度 -20~70℃-20~70℃
操作环境温度 -10~60℃-10~60℃
相对湿度 10~90%RH(无冷凝) 10~90%RH(无冷凝)
规格
外壳材质
工程塑料
ABS(
阻燃级别
)
工程塑料
ABS(
阻燃级别
)
外形尺寸 200×146×37mm 270×212×35mm
开孔尺寸 193×138mm 260×202mm
重量 0.74kg 1.2kg
证书
CE 认证 符合 CE 认证标准 符合 CE 认证标准
七、配套软件
·三碁 HMI 需要配合 SavchSoft_HMI 编辑软件使用,请到三碁网站(http://www.savch.net)的下载中心下载。
·云服务可以通过访问云网站(http://cloud.haiwell.com)使用,推荐下载云 APP。
·云App (Haiwell Cloud ) 下载:
(1)直接扫描右边二维码下载;
(2)IOS 终端可到苹果应用商店(App Store)搜索“海为云”下载。
八、触摸屏校正
HMI 出厂时已经校准,如果需要重新校准,进入参数设置界面,依次选择“硬件设置>显示及声音>触摸校准”,出现如下界面:
+
Savch HMI
Touch crosshair to calibrate
依次点中左上角,右上角,右下角,左下角,中心点的‘+’,重新启动即可。
九、参数设置 按住屏幕的右上角大约 5-10 秒钟,出现如下画面:
简体中文
工程设置 硬件设置 系统信息
选择硬件设置,进入触摸屏的参数设置画面,可以设置网络参数、显示及声音参数、时间参数等设置,修改后,点击保存立即生效。
感谢您选用 SAVCH HMI,若您对我们的产品或服务有问题或不足之处,敬请告诉我们!
公司官网:http://www.savch.net
返回工程 云设置
本地工程、工程下载、
网络工程
网络设置、显示及声音、
时间设置
软件信息、机器信息、
应用更新、系统日志
部件说明
1
液晶和触摸屏
2
指示灯
3
电源插槽
4
COM2
5
Wifi
6
双层
USB
7
COM1
8
LAN

SAVCH SPN-070S/SPN-101S Operation Manual
1. Products receiving
All products have been performed with strict test and inspection. After receiving the product, the following checks shall be performed.
●To check that SAVCH product, an instruction manual is inside of the package
●To check whether model number correspond with model your purchase order.
●To check whether there are damaged parts during transportation and delivering. If there are, do not connect with power supply.
If any of the above checkpoints are not satisfactory, contact your SAVCH ELECTRIC representative for a quick resolution.
2 The notes and installation steps
Notes: ·The wiring should be in strict accordance with the guide of the terminal mark, otherwise it will cause product damage or
burn up.
·There should be sufficient space and distance between the products and other devices to avoid damage to the equipment
caused by poor heat dissipation.
Installation steps:·Fit the HMI into the cutout panel and lock the four buckles on the sides with the mount panel.
3. Model description
Model
Power
Human Machine Interface
Model�
Power�DC24V 0.45A
P/N�1605261053011810012
SPN-070S
SAVCH ELECTRIC CO.,LTD.
Product
name
SPN – 070S W
Screen size:
070: 7 inch
101: 10.1 inch
SAVCH W:Support Wifi
G:Support 4G
None: general
4. The parts and panel cutout
SPN-070S
SPN-101S
SPN-070S panel cutout SPN-101S panel cutout
5. The interface definition
COM1 interface definition
COM2 interface definition
Pin
Definition
Pin
Definition
Pin
Definition
Pin
Definition
1
RS422 TX+/RS485 A+
2
RS232 RXD
1
RS232 RXD
2
RS232 TXD
3
RS232 TXD
4
CANL
3
GND
4
RS485 B-
5
GND
6
RS422 TX-/RS485 B-
5
RS485 A+
7
CANH
8
RS422 RX-
9
RS422 RX+
6. Product specifications
Model
Contents SPN-070S SPN-101S
Power
Input power DC24V±20% DC24V ±20%
Power consumption
5W
9W
Power isolation
Built-in
Built-in
Voltage resistance
500V AC
500V AC
Isolation resistance
Exceed 500MΩ@500VDC
Exceed 500MΩ@500VDC
Vibration endurance
10~25HZ (X
、
Y
、
Z direction 2G/30 minutes)
Environment
Cooling type
Ventilation cooling
Ventilation cooling
Protection structure
IP65
IP65
Storage temperature -20~70℃-20~70℃
Operating temperature -10~60℃-10~60℃
Relative humidity
10~90%RH
(
non-condensing
)
10~90%RH
(
non-condensing
)
Specification
Enclosure
Engineering Plastic ABS
(
Flame-retardant level
)
Dimensions 200×146×37mm 270×212×35mm
Panel cutout
193×138mm
260×202mm
Weight
0.74kg
1.2kg
Certification CE certification Comply with CE certification standard Comply with CE certification standard
7. Savch HMI software
·Savch HMI uses the SavchSoft_HMI software.You can download from. http://en.savch.net.
·Cloud Service can be got by visiting cloud web (http://cloud.haiwell.com)We recommend you to use cloud APP.
·Cloud APP download ways:
(1)Scan the two-dimension code in the right.
(2)Search "Haiwell cloud" in the IOS Iphone APP store.
8. HMI calibration
HMI is calibrated at the factory. If you need to recalibrate, enter the parameter setting interface, select "Hardware Setup> Display&Voice>
Touch Calibration", the following interface will appear:
+
Savch HMI
Touch crosshair to calibrate
Click the upper left corner, the upper right corner, the lower right corner, the lower left corner,
the center point of the '+' in turn, you can restart.
9. Parameter setting
Hold down the upper right corner of the screen for about 5-10 seconds, the following screen appears:
Simplified Chinese
Project Setting Hardware Setting System Information
Select the hardware settings, enter the parameters settings screen of touch-screen, you can set the network parameters, display and
sound parameters, time parameters, etc., after the modification, click“Save”to take effect immediately.
Thank you for choosing Savch HMI. Please let us know if you have any questions or shortcomings about our products or services.
Savch company website:http://en.savch.net
Parts description
1 Liquid crystal and
touch screen
2 Indicator light
3
Power slot
4 COM2
5 Wifi
6 Double-deck USB
7 COM1
8 LAN
Back
Cloud
Local Project,
Network Project
Network settings,
Display&Voice, Time Settings, Machine, Application
This manual suits for next models
1
Popular Computer Hardware manuals by other brands

Key Digital
Key Digital HD Leeza KD-HD1080P operating instructions

ICS
ICS PCI-16REL user guide

Epson
Epson Discproducer PP-50BD user guide

Miranda
Miranda Kaleido-X16 Hardware description and installation manual

Texas Instruments
Texas Instruments bq27220 Technical reference manual

Panasonic
Panasonic CF-VEB471 operating instructions

Cobalt Digital Inc
Cobalt Digital Inc 9902-UDX-FS product manual

Texas Instruments
Texas Instruments TPS3801 Application report

Lindy
Lindy 32118 user manual

ekwb
ekwb EK-FC R9-290X SE Backplate Installation and mounting manuals

Extron electronics
Extron electronics SMP 300 Series user guide

SIIG
SIIG UltraATA 100 Pro user manual