ScaffoldMart MFOUTR18A Installation and operating manual

User Manual & Safety Guide
ONE YEAR
WARRANTY
Thoroughly read
this manual before
assembling or using
scaffolding unit. Failure
to do so can result in
injury or death.
Seriously... read it.
MODEL: MFOUTR18A

USE AND ASSEMBLY
• Only use scaffold unit while complying with local,
state, and national guidelines and legislation. It is the
user’s responsibility to know and follow the rules.
• A competent person should manually inspect
scaffolding prior to each use, ensuring all parts are
present and in good condition and that casters,
siderails, and platforms are properly locked and
components are secured with proper fasteners.
• Only use on level, even surfaces. Erect scaffold unit
plumb, with platform(s) level. Avoid using scaffold on
surfaces that are soft, muddy, debris lled, holey or
otherwise obstructed.
• Refrain from using scaffolding if you are unwell, taking
medication, consuming alcohol, mind-altering drugs
or experiencing any other condition that may impair
your ability to work.
• Rated load capacities are not to be exceeded.
• 18” outrigger is to be used for maximum of two
stacked multifunction units. Larger outriggers are
required when exceeding two stacked units.
• 18” outriggers and guardrails are required whenever a
fall of 71” may occur.
• Four outriggers should be in use whenever possible.
• Outriggers must always be securely fastened in
proper conguration based on the user manual.
Outriggers improperly applied or secured will not
stabilize scaffold unit.
• Casters must always be secured with span pins and
caster brakes must be locked before climbing or
standing on scaffolding.
• Do not use any scaffolding component that is
damaged or if parts are missing.
• Caster brakes should be applied for entirety of
setup and use. Casters should only be unlocked to
move scaffold, never with personnel, equipment or
materials on the unit.
• Follow manufacturer instructions assembling
products. Do not skip steps and make certain all
connections are secured.
• Double check all connections before climbing unit to
make certain they are properly secured.
• Make certain outriggers are attached such that all
eight contact points with the ground are level.
DO NOTS
• Never use this outrigger when stacking more than two
6’ Multifunction Units.
• Never over-tighten tube clamps on outriggers.
• Never move a scaffolding loaded with anything,
including personnel, tools, materials, etc.
• Never use on uneven, soft or obstructed surfaces.
• Never lean outside the perimeter of scaffolding, this
can cause tilt conditions.
• Never exceed 71” standing height without guardrails
and outriggers installed.
• Never use any means other than manufacturer
approved equipment to alter the standing height of a
platform.
• Never exceed manufacturers rated load capacity.
Safety Guide
Read Instructions thoroughly before assemblage. Non-compliance with
guidelines may result in serious injury or death.
Do Not Over Encumber
This unit was designed for a maximum
capacity load of 1,111 lbs (504 kg)
Weight Capacity DECREASES with
stacking. Only use Scaffoldmart
outriggers and stacking units.
Metal Conducts Electricity
Never use scaffolding unit in proximity
to live electrical circuits or power lines.

Assembly Instructions - Single Unit
SINGLE UNITS USE 30 DEGREE POSITION
For single units, outrigger attach ush with square tube such that adjustment holes in frame are
covered. Always install with outriggers angled away from one another.
NOTE BEFORE ASSEMBLY: This outrigger is built to attach in two congurations, depending
on the conguration they’re being used to stabilize. One for use on single 6’ multifunction
units, another for two stacked units. DO NOT use this outrigger stacking more than two units.
1 Start with one 6’ multifunction unit fully
assembled, with all parts securely fastened
and locked.
2 Before attaching outrigger, insert caster into
receiver and fasten with a span pin.
3 To attach outrigger, align the square face
of the vertical tube of the outrigger with
the square face of the vertical tube of the
scaffold frame.
4 Set outrigger at a height where its caster is
in rm contact with the ground, such that it’s
level with the casters already applied to the
scaffold unit.
5 Outriggers fasten by way of clamps. Place
clamps so their ends wrap around square
tube, then secure the hand-tightening
levers. Turn until hand-tight, then a little
more.
30°
Customer Service:
1 [phone]
[email protected]
scaffoldmart.com

Assembly Instructions - Two Units Stacked
STACKED UNITS USE 60 DEGREE POSITION
For two stacked units, outrigger attach ush with square tube such that adjustment holes in frame
are covered. Always install with outriggers angled away from one another.
1 Start with one 6’ multifunction unit
fully assembled, with all parts securely
fastened and locked.
2 Before attaching outrigger, insert caster
into receiver and fasten with a span pin.
3 To attach outrigger, align the square
face of the vertical tube of the outrigger
with the square face of the vertical tube
of the scaffold frame.
4 Set outrigger at a height where its caster
is in rm contact with the ground, such
that it’s level with the casters already
applied to the scaffold unit.
5 Outriggers fasten by way of clamps.
Place clamps so their ends wrap around
square tube, then secure the hand-
tightening levers. Turn until hand-tight,
then a little more.
6 With outriggers securely fastened,
continue construction of second
multifunction unit and guardrails.
60°
11
YEAR
ONE YEAR
WARRANTY
ScaffoldMart guarantees this product against any
material defect for a period of one year beginning at
the time of purchase. This warranty does not cover
damages or injury due to inappropriate or incorrect
use, care or maintenance of your unit.