Scantron sky IVW2221 User manual

BRUsky-S
version 1.0
Instruction manual
sky
TM
Video indoor station with digital 8.9 cm (3.5“)
TFT display for surface-mount, in anodised
aluminium
IVW2221
H:\Dokumenter\02 PB Scantron dørtelefoni\05 Hustelefoner\Sky\Arbejdsfiler for Sky

BRUsky
version 1.0
Congratulations to your new
video indoor station with optional external image buer!
green ON incoming door call or internal call
active voice communication
green blinks busy speech and video channel
newly stored image
red ON ring tone is switched o, incoming
call is not signalled acoustically
red blinks additional functions activated
see congurable functions
function key
image button
call OFF button
navigation button DOWN
menu button
navigation button UP
digital 8.9 cm
loudspeaker
microphone
red LED
indication call OFF, additional function
activated
green LED
indication incoming call, speaking
activated,
(3.5") TFT
speech button
Side 1

A ring tone signals an
incoming call.
The green LED is ON.
Speaking
Shortly press the speech button to accept the call or longer than 1 second to switch on
simplex communication during the voice communication.
The green LED is ON.
Shortly press again the speech button or the blue door release button to end the call.
Ends the communication after 4 seconds.
Automatic call cut OFF after 2 minutes.
Door release
Preset ex works 4 seconds.
Switch an image
Shortly press the image button to show the image of the front-door station on the display.
also see additional functions
Menu
This button is used to set image and ring tone parameters.
see page 5 and 6
Navigate the menu
These buttons are used to set image and ring tone parameter.
see page 5 and 6
Operation
Switch o the ring tone
Press the call OFF button. When a call comes in, no acoustic signal sounds.
The red LED is ON.
Swicthing lights / internal
calls / additonal functions
Shortly press the function key to switch the lights, to call another indoor station or to
(de-)activate the call diversion resp. door release automatic.
Switching lights is preset ex works, otherwise
a conguration will be necessary, see
congurable functions
BRUsky
version 1.0
Side 2

1. Shortly press the image button . The image of the video front-door station ap-
pears on the display.
2. Shortly press the menu button . The menu for settings is faded-in.
3. Shortly press the menu button again to switch over to the next parameter.
4. Shortly press the navigation button UP or DOWN to change the parameter
value. The change is visible immediately in the video image.
5. The menu is switched o automatically after 10 seconds, if no button is pressed.
Or: Shortly press the function key to switch o the menu.
Setting of the display
The setting of contrast, brightness, color intensity and conversation volume is realised
quickly and easily in the symbol menu of the display when in stand-by mode (speaking
and video o).
contrast
brightness
color intensity
conversation volume*
The display
image of the camera or
video front-door station
no. 05
ring tone mute
call diversion activated or
door release automatic
activated
The fade-in of the symbols in the video image is realised automatically.
If the speech button was pressed, the fade-in of the symbols is already nished after
3 seconds.
The fade-in of the video images is realised immediately after pressing the image button
or after receiving a door call.
Optional, the speech button can be pressed in order to receive noises in addition to the video image when in
stand-by mode (speaking and video o).
Setting the video image
image buer activated
*adjustable only during the communication
BRUsky
version 1.0
Side 3

Setting ring tone volume and ring tones
1. Shortly press the menu button . The main menu is called up.
2. With the help of the navigation buttons UP or DOWN the menu ring
tone parameter can be selected. Conrm the selection by pressing the menu button
again.
3. You are now in the menu ring tone parameter. With the navigation buttons UP
or DOWN the required ring tone can be selected.
When selecting a ring tone, the ring tone sounds immediately.
When selecting the communication volume, the actual ring tone sounds immediately
in the selected volume after the change.
The menu is switched o automatically after 10 seconds if no button is pressed.
Shortly press the function key to switch o the menu.
The setting of ring tone volume and the selection of the required ring tone is realised quickly and easily in the symbol menu
of the display when in stand-by mode (speaking and video o).
Your settings in the OSD menu
main menu
selected
parameter menu
toolbar to select parameter menu
menu
ring tone parameter
adjusted value of the
selected parameter
0, 1, 2, ..
toolbar to select parameter
selected parameter menu
selected parameter
BRUsky
version 1.0
ring tone volume
for door calls
ring tone selection
for oor door calls
ring tone selection
for internal calls
ring tone selection
for sub ring tone
1, 2, 3, 4
ring tone volume
control function*
internal call*
external image buer
ring tone parameter
date / time
external image buer
delete external
image buer
* symbol appears only
after conguration, not
in factory setting
Side 4

External image buer
Setting date and time
The setting of date and time for stored images in the external image buer is realised quickly and easily in the OSD menu of
the display when in stand-by mode (speaking and video o).
1. Shortly press the menu button . The main menu is called up.
2. With the navigation buttons UP or DOWN select the symbol image buer
setting menu. Conrm the selection by pressing the menu button again.
3. The menu to set the image buer appears. The white-backlit number can be changed
with the navigation buttons UP and DOWN . With the menu button you
can forward to the next position.
4. If setting the date is nished, pressing the menu button again calls up the time
setting. Proceed as described in the date setting.
5. By pressing the menu button again the menu is deactivated and the settings are
stored in the image buer.
main menu
selected
parameter menu
toolbar to select parameter menu
menu date / time image buer
selected parameter menu
BRUsky
version 1.0
Side 5

BRUsky
version 1.0
Store images automatically and manually
In connection with an external central image buer FVM1000-0400 up to 64 images can be stored.
Store images
Press the menu button again longer than 4 seconds, an acknowledgement tone sounds
and the main menu is faded-in for 3 seconds. The symbol image buer changes from green
to red, the automatic image recording is deactivated.
Store an image manually
Press the navigation button UP when the camera image is activated. A snapshot of
the camera image is taken and the image is stored in the image buer. To conrm the sto-
ring an acknowledge ment tone sounds. The image is stored in the image buer.
If images were stored that have not yet been seen, the green LED blinks.
Store an image automatically
Activate the automatic image recording by pressing the menu button longer than 4
seconds. An acknowledgement tone sounds. The main menu is faded-in for 3 seconds, the
symbol image buer changes from red to green. The automatic image recording is activa-
ted.
When receiving a door call, an image is stored automatically.
If images were stored that have not yet been seen, the green LED blinks.
With the shortcut function you can view the stored image immediately. Thus, shortly press
the menu button .
Side 6

BRUsky
version 1.0
If the image buer indication blinks green, new images were stored at an incoming door
call
1. Press the menu button to display the image of the image buer.
2. Browse through all new stored images with the navigation buttons UP and DOWN
.
Alternatively select the image buer via the
menu (when images have been already seen).
3. Press the navigation button DOWN for 4 seconds to to delete the image. A short
acknowledgement tone sounds. The image is deleted. The image stored before is shown.
Delete all images
All images can be deleted in the OSD when in stand-by mode (speaking / video o).
1. Press the menu button
. The main menu is called up.
2. With the navigation buttons UP or DOWN select the symbol delete image
buer. Conrm the selection by pressing the menu button again.
3. The menu delete image buer appears. With the navigation buttons UP or
DOWN select the checkmark.
4. Conrm by pressing the menu button . Deleting the image buer can take sever-
al seconds, depending on the number of stored images.
Call and delete images
Image buer
menu
delete image buer
main menu
selected
parameter menu
toolbar to select parameter menu
View stored images
Side 7

BRUsky
version 1.0
The following functions can be congured at your video indoor station and for the use of
further indoor stations. Therefore please contact your qualied electrician.
Switching lights, internal call, call diversion and
door release automatic can be used only
alternatively.
Call indoor stations (internal call)*
To call antother indoor station, shortly press the function key . A short acknowledge-
ment tone sounds, if the call has reached its call destination.
When accepting the call at the called device, a voice communication is established.
* max. 1 call destination
More than one further indoor station
In case of more than one further indoor station (max. 10) the call destination is selected
over the main menu and called by pressing the menu button . An acknowledgement
If the call is accepted at the called device, another acknowledgement tone sounds and the
voice communication will be established.
Receive internal calls
Press the speech button a voice communication is established.
The green LED is ON.
If your video indoor station receives an internal call from a known indoor station, the name
of this indoor station is shown*.
*conguration by a qualied electrician is needed
Congurable functions
Send internal calls over the menu internal
indication of internal caller in the menu
menu
internal call
menu
internal call
selected
internal call
Side 8

BRUsky
version 1.0
Open the floor door
If the oor push-button at the oor door is pressed, the oor door can be opended with
the blue door release button (instead of the front-door) within 30 seconds.
Door release automatic
An incoming door call directly eects the opening of the door if this function is activated.
Shortly press the function key activated.
the red LED blinks.
Shortly press the function key again deactivated.
Switch lights with the
door release button
if no voice communication is established
Parallel call
A second indoor station sounds together with the rst one in case of an incoming door,
oor or internal call. The ring tone sounds at both indoor stations.
Send control function
If control functions (max. 10) are programmed, those can be (de-)activated in the menu
control function. The switching modes of the control functions (ON/OFF) are indicated by
colored points (red/green).
Call diversion
The incoming call is diverted to a second indoor station.
Shortly press the function key activated.
The red LED blinks.
Shortly press the function key again deactivated.
A call cannot be diverted to all TCS indoor stations.
The diverting indoor station is not signalling the diverted call.
(de-)activate control functions
in the menu control functions
Side 9

(de-)activate control functions
in the menu control functions
BRUsky
version 1.0
Additional functions
Cleaning
Video surveillance
Shortly press the image button to show the image of the front-door station on the dis-
play. By pressing the button again, further cameras can be selected.
Error indication
If the two LEDs icker continously and shortly and if there are beep tones when pressing
the buttons, there is an error at the device or within the system.
Please inform your qualied electrician.
Clean the device with a dry or slightly moist cloth.
Remove stronger soillings with a mild household cleaner.
Avoid water from entering the device! Do not use any abrasive detergents!
The adjoining sym-bol shows, that the device has to be disposed separately from
domestic waste. The materials used are recyclable. Please do help protecting our
environment and dispose the device via a collection point for electronic scrap.
Information on disposal
Side 10