ScatterBox HDM220 User manual

Quick Start Guide - qHDM220 Copyright 2021 System Q Ltd
1
HDMI KVM Extender Over CAT5/IP 1080P
ScatterBox is a registered trademark of System Q Ltd
HDM220 / HDM216 / HDM217 - Quick Start Guide
www.systemq.com/PDF
/manual/xHDM220.pdf
The HDMI KVM extender allows for viewing of HDMI video and USB control from up to 120m away from
your DVR using your existing CAT5/6 set-up.
The HDMI Mules can be used for point-to-point access (1 cable between each unit and no switch) or in
cascade mode with additional monitors/receivers connected through a network switch, letting
multiple usershave USB control from different receivers.
HDM217 - Transmitter
1. 5v DC power input
2. HDMI input port
3. USB output port
4. LED power indicator
5. LED keyboard indicator
6. LED mouse indicator
7. LAN RJ45 Socket
7a. data LED
7b.bandwidth / connection LED
8. Reset button
HDM216 - Receiver
1. 5v DC power input
2. HDMI output port
3. USB dual input ports
4. LED power indicator
5. LED keyboard indicator
6. LED mouse indicator
7. LAN RJ45 Socket
7a. data LED
7b.bandwidth / connection LED
8. Reset button

Quick Start Guide - qHDM220 Copyright 2021 System Q Ltd
2This symbol indicates that equipment must not be mixed with general household waste. For treatment, recovery and recycling please return to your local designated
WEE/CG0783SS collection point as defined by your local council.
All specifications are approximate. System Q Ltd reservesthe right to change product specifications or features without notice. Whilst every effort is
made to ensure that these instructions are complete andaccurate, System Q Ltd cannot be held responsible for any losses,no matter how they arise,
from errors or omissionsin these instructions, or the performance or non-performance of the equipment refered to.
HDMI KVM Extender Over CAT5/IP 1080P
ScatterBox is a registered trademark of System Q Ltd
1) Connect an HDMI cable from the source (DVR) to the transmitter. Ensure that HDMI cable is no longer than
5 metres for a 1080P input signal or 10 metres for a 720P input signal.
2) Connect the HDMI cable output from the receiver to the HDMI monitor/HD TV, ensure that the HDMI cable
run is no longer than 15 metres.
3) Connect a network cable between the transmitter and receiver of no longer than 80 metres using CAT5,
100 metres using CAT5E or 120 metres using CAT6.
4) Connect the 5V Power Supplies to the transmitter and receiver (included with the product). The power
LEDs will light up. When the signal LEDs light and flicker, the equipment is ready to use.
5) If using a USB mouse or keyboard plug them into the USB ports on the receiver. Fit the USB cable between
the transmitter and DVR, or item you are controlling with the mouse. The USB cable is also included.
HDMI Version
HDMI 1.3
HDCP Version
HDCP 1.2
Video Bandwidth
Supported HDMI Resolutions
640*480@60Hz 800*600@60Hz 1024*768@60Hz
1280*720@60Hz 1360*768@60Hz 1440*900@60Hz
1400-1050@60Hz 1680*1050@60Hz 1920*1080@60Hz
Audio
PCM (44.1KHz, 48KHz)
HDMI Connector
Type A, 19 pin, Female
LAN Connector
RJ45
Power Supplies
2 x 5vDC/1A
Power Consumption
HDM217 Transmitter 700mA HDM216 Receiver 700mA
Power Connection on TX & RX
2.1mm DC Jack
Network Connection
RJ45 cable CAT5/CAT5E/CAT6 max run 80m/100m/120m
HDMI cable run to HDM217 Transmitter
If source 1080P max run 5 metres – if 720P max run 10 metres
HDMI cable run from HDM216 Receiver
15 metres
Operating temperature Range
0°C ~ +50°C
Operating Humidity Range
10% ~ 95% (Non condensing)
Transmission
One HDM217 TX can transmit video & audio to multiple HDM216 RXs
Weight
Transmitter:240g Receiver:240g
Dimensions
109.6(L) x 89.5(W) x 26.3(H)mm *2pcs
Colour
Black