SCC Comelit User manual

Smart Choice Communications | [phone] | www.smartchoiceus.com | [email protected]
© 2018 Smart Choice Communications, LLC
16
the system is busy
1 2
5. System function
PERFORMING CALLS
How to call from the external unit
To send the call from an external unit, touch the button
corresponding to the user you want to contact.
» On the external unit the caller illumination LED will light
up, the LED will flash and the confirmation tone will
sound. The video image from the external unit will appear
automatically on internal monitor/s.
»If the system is busy: the LED will flash and the
external unit will emit the system busy tone.
How to answer a call from an internal unit
» On receipt of a call from the external unit you will hear the
call ringtone
Press to enter into communication with the caller
» the LED will illuminate on the external unit.
Press again to terminate the call.
A call from the external unit always takes priority over an
intercom communication or a paging call
» the call in progress will be ended for the other devices.
PAGING CALL
How to initiate a paging call
Press to initiate the all-page chime
»After the chime sounds, a 30 seconds message can be
broadcast to all monitors on the system (maximum 4
monitors).
How to answer a paging call
Press to answer the paging call
»a (300 seconds) point to point conversation between the
two monitor is established.
»the paging call will be terminated for the other devices.
A call from the external unit always takes priority over an intercom communication or a paging call
» the call in progress will be terminated for the other devices.
12
LOCK RELEASE FUNCTION
√During “call in progress” or during Self-ignition.
Press to release the lock.
» the LED will illuminate on the external unit.
Press the desired key once to activate the function associated with it.
Wait for approximately 1 sec. before pressing the same key again. Pressing the same key several times in quick succession will
cancel the command.
Quick Reference Guide for Comelit Intercom

Smart Choice Communications | [phone] | www.smartchoiceus.com | [email protected]
© 2018 Smart Choice Communications, LLC
17
cycle
MAIN
UNIT UNIT 1 UNIT 2 UNIT 3
MAIN EXTERNAL
UNIT
ACTIVATION/DEACTIVATION DOCTOR MODE
Press the programmed button for 3 sec to disable/enable the
Doctor function.
»3 flashes (every 5 sec.) of the LED indicate that the Doctor
function is active.
PRIVACY MODE
Press to disable/enable the ringtone for calls from the external
unit and paging call.
» The red LED indicates that the Privacy function is active.
In Privacy mode the paging call are still received
SELF-IGNITION FUNCTION
√Self-ignition is possible only when the system is in standby
Press the self-ignition button ( by default) to display on the
monitor the video from the external unit.
Press again to cycle through several cameras
If a call is underway with an external unit it is NOT possible
to cycle between the external units
Press and hold the key to disable / enable the function.
Video memory
Video messages list
Wi-Fi setup
Setup
Wi-Fi reporting unconnected
App registration enable
Date and time settings
Language
Information
Reset
Reset WiFi configuration
Factory reset
Reset APP
By installing and configuring the COMELIT App on smartphone /
tablet it is possible to answer video door entry calls from a local and
remote network (or mobile network); it is possible to make a Self-
ignition on cameras/entrance panels and send commands to actuator
modules.
6.1 WI-FI CONNECTION STATUS
Access point: If the system requires wireless connection of
the monitor, link the device with the local router
Signal strength:
Excellent Good Moderate Weak
Connection absent: Monitor Wi-Fi reception is enabled,
therefore you need to check the router conditions (on/
o, correct operation, distance from the monitor, correct
password).
Router connected, no internet: Check with your internet
provider.
6. Device functions
17
cycle
MAIN
UNIT UNIT 1 UNIT 2 UNIT 3
MAIN EXTERNAL
UNIT
5.5 ACTIVATION/DEACTIVATION DOCTOR MODE
Press the programmed button for 3 sec to disable/enable the
Doctor function.
»3 flashes (every 5 sec.) of the LED indicate that the Doctor
function is active.
5.6 ACTIVATION/DEACTIVATION PRIVACY MODE
Press to disable/enable the ringtone for calls from the external
unit and paging call.
»The red LED indicates that the Privacy function is active.
In Privacy mode the paging call are still received
5.4 SELF-IGNITION FUNCTION
√Self-ignition is possible only when the system is in standby
Press the self-ignition button ( by default) to display on the
monitor the video from the external unit.
Press again to cycle through several cameras
If a call is underway with an external unit it is NOT possible
to cycle between the external units
Press and hold the key to disable / enable the function.
Video memory
Video messages list
Wi-Fi setup
Setup
Wi-Fi reporting unconnected
App registration enable
Date and time settings
Language
Information
Reset
Reset WiFi configuration
Factory reset
Reset APP
By installing and configuring the COMELIT App on smartphone /
tablet it is possible to answer video door entry calls from a local and
remote network (or mobile network); it is possible to make a Self-
ignition on cameras/entrance panels and send commands to actuator
modules.
WI-FI CONNECTION STATUS
Access point: If the system requires wireless connection of
the monitor, link the device with the local router
Signal strength:
Excellent Good Moderate Weak
Connection absent: Monitor Wi-Fi reception is enabled,
therefore you need to check the router conditions (on/
o, correct operation, distance from the monitor, correct
password).
Router connected, no internet: Check with your internet
provider.
Device functions
ACTIVATION/DEACTIVATION