Schaeffler ProLink CMS User manual

5 Connecons
(1) USB B (for future funcons)
(2) USB A (for future funcons)
(3) PC/Ethernet (SmartWeb configuraon)
Default IP address: 192.168.1.100
(4) Fieldbus connecon (for future funcons)
(5) Ethernet 1 (internal ProLink communicaon)
(6) Power supply connecon
ProLink CPU Module
Connecon overview
1 General safety informaon
 Read this document carefully before seng up the
Schaeffler ProLink device. Keep the document during
the enre service life of the device.
 Adhere to the operang instrucons and the technical
data. Otherwise personal injury or damage to property
may occur.
 The device must be suitable for the planned applicaons
and for the environmental condions without any
restricons.
 Only use the device for its intended purpose (see
Funcons).
 The manufacturer assumes no liability and warranty
for any consequences caused by incorrect use of the
device.
 The device must be installed and electrically connected,
set up, operated and maintained by qualified and
authorised specialists.
 Protect the device units and cables against damage.
2 Funcons
The ProLink CPU module collects data from the vibraon
modules and converts the data into characterisc values
and trends. Via the SmartWeb soware, this data can be
directly analysed on the device.
Electrostac discharge
The device contains components that can be damaged or
destroyed by electrostac discharge. To safely avoid
electrostac discharge, you must operate the device on a
grounded mounng rail. When handling the device observe
the required safety precauons against electrostac
Contact voltages and ambient condions
Mount the device in a control cabinet to protect it from
dangerous contact voltages and ambient condions. The
installaon of the control cabinet must be in accordance
with local and naonal regulaons.
3 Installing the device
1. Ensure that the device is disconnected from power.
2. Mount the device vercally in a control cabinet on a
35 mm DIN mounng rail.
3. Leave enough space between the device and the top
and boom of the control cabinet to ensure good
venlaon.
1. Connect the VDC power supply unit to the power supply
connecon of the CPU module.
2. Connect the power supply connecon of the CPU
module to the connecon of the vibraon module.
Please note the maximum cable lenght of 3 meters. See
also the illustraons in Connecons and Wiring.
4 Connecng the power supply
Electrical connecon
The device must be connected by a qualified electrician.
The local and naonal regulaons for the installaon of
electrical devices must be adhered to. 6 Wiring
1 2 3 4
1
3
Front view Top view
Top view
2
4
5
6
discharge (ESD) in accordance with EN 61340‐5‐1 and
IEC 61340‐5‐1.

Schaeffler Monitoring Services GmbH
Kaiserstraße 100
52134 Herzogenrath
Germany
Phone: [phone]‐66
Fax: [phone]‐59
Support: www.schaeffler.de/en/technical‐support
Internet: www.schaeffler.de/en/services
Further informaon
This connecon overview contains all the informaon
required for installaon, connecon and operaon. For
further informaon on the Schaeffler ProLink device or
the Schaeffler SmartWeb soware please refer to the
respecve manual of the same name. The current
edion of the manuals can be downloaded here:
www.schaeffler.de/en/condion‐monitoring/prolink
All details have been carefully compiled and checked.
However, we can accept no liability for potenal errors
or omissions. We reserve the right to make technical
modificaons.
© Schaeffler Monitoring Services GmbH
Version 1.4, Edion: March 2021
Reprinng, including excerpts, only with our permission.
8 Dimensions
75 mm
139,5 mm
Internal
communi‐
caon
Next
module
Vib CPU
24 VDC
0 V
35 mm
120 mm
License informaon
The Schaeffler ProLink firmware uses GPL open‐source
libraries to provide certain funconalies of its product
ProLink in conformance to the requirements of the GPL
Version 2 (3b) and Version 3 (6b).
You receive a copy of the GNU General Public License along
with this the Firmware SmartWeb.
GPL Wrien Offer
Schaeffler Monitoring Services GmbH on request will
provide for at least three years from the delivery date of
the ProLink device machine‐readable source code of the
used libraries that are under the GPL to the requester.