Schiavello Krossi Electric Adjust Desk User manual

Krossi
Electric Adjust Desk
Installation Guide

Krossi
Electric Adjust Desk Installation Guide (SI-P-23)
Page 2
Parts Included
You will need:
Worktop with beam, control box and
switch pre-installed
Legs x 2
Phillips Head Screw Driver
(Star Tip)
M4 Screw (for the legs) x 8
M6 Screw (for the beams) x 4
each
Beam
Control Box
Switch

Krossi
Electric Adjust Desk Installation Guide (SI-P-23)
Page 3
Step 1
Step 2
Place worktop upside down so that you see the
beam, control box and switch
Note: Ensure your worktop is on a clean flat surface.
Remove the 4 x M6 Screws from the beam and set
aside.

Krossi
Electric Adjust Desk Installation Guide (SI-P-23)
Page 4
Step 3
Step 4
Remove the 8x M4 Screws in the worktop and
set aside separately.
Place legs standing up.
Move cord until the plug is visible. This will need to be
plugged in later.

Krossi
Electric Adjust Desk Installation Guide (SI-P-23)
Page 5
Step 5
Step 6
Position leg as per below to commence fixing
to the worktop.
Note: Ensure the cord is not caught between
the beam and the leg
Loosely screw in 4 x M4 screws to allow leg adjustment
and hole alignment.

Krossi
Electric Adjust Desk Installation Guide (SI-P-23)
Page 6
Step 7
Step 8
Repeat steps 4 to 6 with other leg
Tightly fix the legs to the beam by fastening the M6 screws
into position
Force beam to create alignment of holes (if required)

Krossi
Electric Adjust Desk Installation Guide (SI-P-23)
Page 7
Step 9
Step 10
Tighten all M4 screws to ensure securely
fastened
Plug the leg cords into the control box
Repeat for both legs
Note: Ensure the arrow head clips in.

Krossi
Electric Adjust Desk Installation Guide (SI-P-23)
Page 8
Step 11
Flip the desk over, and plug into power point.
Note: When flipping the desk over, please take care
with the switch that protrudes past the worktop as
this can damage.

Krossi
Electric Adjust Desk Installation Guide (SI-P-23)
Page 9
Initial Setup &
Troubleshooting
Height Adjustment
Manual Reset
1.Press the DOWN button until the desktop has reached
its lowest position
2.Press the DOWN button again and hold for 5 seconds
until desktop moves down further. You will hear a
click.
3.Release the DOWN button
4.The electric adjustable desk can now be used
normally.
For further assistance, please contact your Schiavello
representative or head office on 03 9330 8888
Upward and downward movement
˄
˅
Press and hold the up or down key until the desired
height is reached.

Krossi
Electric Adjust Desk Installation Guide (SI-P-23)
Page 10
Ergonomic Considerations
DESK SETUP - SITTING
Setup
•Minimum height must be greater than any under-desk
furniture/obstruction
•Program User height to Seated User preferred level
Ergonomics
•Chair at comfortable height
•Straight back
•Forearms at or slightly above desk height,
•shoulders relaxed
•Wrists straight in line, keyboard flat
•Thighs parallel to ground, knees at 90°
DESK SETUP - STANDING
Setup
•Maximum height must be lower than any above-desk
furniture/obstruction
•Program User height to Standing User preferred level
Ergonomics
•Straight back
•Forearms at or slightly above desk height,
shoulders relaxed
•Wrists straight in line, keyboard flat
•Straight back