Schreiber New Windsor 615 / 0370 Datasheet

Important - Please read these instructions fully before starting assembly
Dimensions
Issue 2 - 21/04/11
Width - 99cm
Depth - 57cm
Height - 190cm
New Windsor Wardrobe
Assembly Instructions - Please keep for future reference 615 / 0370
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

1
Safety and Care Advice
!
Cleaning Guidance
Care and maintenance
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• This product has been finished using natural materials. As a living material, you may notice some
variation in the grain and colour shade between the different components.
• Unlike a synthetic or man-made material which has a uniform finish, a feature of natural wood is its
variation in grain and colour. We wish to reassure you that this is quite normal and is not the result of any
manufacturing fault.
• Where sheets of wood are joined together, a line may be detected. Again, this is normal and is not
animperfection.
• A classic characteristic of oak timber is medullary rays. These are natural rays or streaks usually seen
across the grain. These rays have a different cellular structure and reflect light differently to the surrounding
wood. These rays or streaks are a unique characteristic of natural oak and are there not a defeat.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Parts of the assembly will be
easier with 2 people.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• To ensure an easier assembly,
we strongly advise that all fittings
are only finger tightened during
initial assembly. Only upon
completion of the assembly
should all fixing points be fully
tightened.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Make sure you have enough
space to layout the parts before
starting.
• Dispose of all packaging
carefully and responsibly.
• Place the product on flat and
steady surface during use.
• Keep these instructions for
future use.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Important - Please read these instructions fully before starting assembly

Please check you have all the parts listed below
Components - Parts
2
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
2
1Side panel (left)
(55 x 126.5cm)
4Bottom panel (52.3 x 87cm) 2
3Top panel (57 x 99cm)
5Lower support rail (4 x 87cm)
7
6Front support rail (2 x 87cm)
8Back panel x 2 (63.1 x 90cm)
11 Hanging rail (2.3 x 86.5cm)
9Door (left) (43.2 x 126cm)
10
12 Base unit (97 x 56 x 60cm)
Side panel (right)
(55 x 126.5cm)
Rear support rail (2 x 87cm)
Door (right) (43.2 x 126cm)

Please check you have all the fittings listed below
Components - Fittings
3
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
30mm Bolt x 2
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
A
25mm x Bolt x 2
Tools required
Door hinge x 6
Bracket x 2
15mm Screw x 40
ABC
Metal dowel x 10 Locking nut x10 50mm Bolt x 6
12mm Screw x 28
DE
GJ
K
F
H
Door handle x 2
Wall fixings (screw & strap)
x 2 sets
L M
Allen key x 1
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150
1 2 345 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
7mm Suitable drill bit
(for use with wall plug)
Drill
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Drawer handle x4 25mm Bolt x 4
NP
Note:
Pre-assembled Note:
Pre-assembled

2
A
A
A
A
A
A
A
A
A
A
2
Assembly Instructions
4
Step 1
Preparing panels
Lay left side panel and
right side panel flat on
the floor with the main
fixing holes facing up
.
Screw metal dowels
into panels ,
as shown.
Note:Insert metal
dowels as far as shown.
Do not over tighten.
A
A
1
2
21

B
B
B
B
B
4
5
6
7
1
Assembly Instructions
5
Step 2
Attaching support
rails and bottom panel
a: Locate front support
rail and rear support
rail onto left side panel
as shown.
Insert locking nuts into
the support rails as
shown.
Use a screwdriver to turn
locking nuts clockwise
to secure.
b: Locate lower support
rail into position.
Insert locking nuts and
turn clockwise to secure.
c: Locate bottom panel
into position.
Note:Ensure the fixing
holes are facing down
and the magnets are at
the front.
Insert locking nuts and
tum clockwise to secure.
B
B
B
B
B B
6
7
1
5
4
Magnets
at front
Top
Bottom

B
B
B
B
B
A
A
A
A
A
4
5
1
7
2
6
Assembly Instructions
6
Step 3
Attaching right side
panel
Carefully align right side
panel and locate into
position.
Insert locking nuts as
shown and turn
clockwise to secure.
B B
2
B

C
C
C
C
C
D
C
1
2
3
D
Assembly Instructions
7
Step 4
Attaching top panel
Carefully turn the unit
over onto it's front.
Locate top panel into
position.
a: Secure in position
using fixings into side
panels and .
b: Finally secure the top
panel using fixings
into top panel .
D
C
3
12
3

E
8
8
3
2
Assembly Instructions
Step 5
Important:
Unit MUST
be 'square' when
back panels are attached.
!
Attaching back panel
Attach back panels to
the back of the wardrobe
using screws .
E
8
8

F
F
G
F
G9
10
G
F F
9
F
F
F
F
G
G
G
G
Assembly Instructions
9
Step 6
Preparing doors
Separate the two halves
of hinges .
Assemble one half of
hinges to left door
using fixings .
Repeat for right door .
F
F
10
9
G