Scolmore ESP Aperta A1IPMW User manual

A1IPMW & A1IPMB
Quick Start Guide
The latest product manuals and software is available online:
https://www.espuk.com/technical_support
REV: D23
Aperta IP PoE Monitor with App

1. Installation
Connect the Monitor to a switch/network or alternatively directly to a Door Station using the RJ45 port [1].
If the connected network does not support PoE, then DC12V1A needs to be applied to the 12V & GND
terminals [2].
*All system cabling has been tested with Cat5E UTP PVC Cable.
**Maximum distance of 100m to PoE switch is supported.
Cables
Mounting
Plate
Rawl
Plugs
Connect to a normally open switch to trigger
the monitor’s doorbell facility
UNUSED
GND
12V
Alternative power connections
BELL
GND
NC
NO
COM
B
A
[1]
[2]
Monitor Lock Connections
RS485
IP/PoE connection
Connect to a
door chime

2. Monitor Installation Mode Configuration
The A1IPMW and A1IPMB can be used on both Villa and Apartment systems, but they require to be config-
ured into the correct “Build” mode.
Ensure the monitor has been powered up, using either the DC12V input [1] or PoE Input [2].
One the monitor has fully initialised click on “System Settings”, and then enter the code “31415” and press
“OK”.
• Select “Villa” for Single Way Systems
• Select “Build” for Multi Way Systems.
Then adjust the Device type using the onscreen arrows, and then press “OK”.
3. Villa Monitor Installation
• if a monitor is being used with Villa Outdoor Station that is at factory default, then the Monitor will not
need configuring, and will operate once fully initialised.
• If the monitor is to be used with a configured Villa Outdoor Station, then do the following:
1. Once the monitor has fully initialised; Click on “System Settings”,
and then enter the code “666666” and press “OK”.
2. Then select “Extension”, and then enter the Rooms Extension [01~06]
Note:
Ensure there is always a monitor with the Extension “01” on the system.
Ensure Section 2 has been completed, to ensure the monitor is set to the Villa Mode.
A Maximum of 6 monitors on a single system is recommended.
If more are required, please contact ESP Technical for further information.
01Ext.
Please enter an extension number:
Extension
4. Multi Monitor Installation
One the monitor has fully initialised and section 2 has been completed; click on “System Settings”, and then
enter the code “666666” and press “OK”.
Then select “Extension”, and then enter the Rooms Extension.
EX. 1st Building, Room 0005, Extension 1
01Bd.0005Room01Ext.
Note:
Ensure there is always a monitor with the Extension “01” on the system.
A Maximum of 200 addresses on a single system is recommended.
If more are required, please contact ESP Technical for further information.
01Bd.0001Room01Ext.
Please enter an extension number:
Extension

Contact Details
Elite Security Products UK, Unit 7 Target Park, Shawbank Road, Lakeside, Redditch, Worcestershire, B98 8YN
Tel: [phone] Fax: [phone] Email: [email protected]
Registered in England, Company Registration Number: 02769392, VAT Registration: GB614686525
For more product information please visit www.espuk.com E&OE - Errors and Omissions Excepted. D23
6. App Connectivity
Preparation For Use
Ensure that the smart phone you are using is connected to the same
Wi-Fi network that you would like to attach the monitor to.
Ensure that you have a mobile device running iOS 8 or higher,
Android 4.1x or higher, and a 2.4GHz Wi-Fi connection.
Download the Click Smart+ App on you mobile device from the
App Store or Google Play.
Sign in or Register following the instructions on the Click Smart+ App.
1. Once the Monitor has been powered up, it will automatically create a hotspot name “SmartLife-xxxxx”
(the last 6 digits will match this monitor’s MAC address)
2. On the desired Smart Phone go into the Wi-Fi settings an connect the above SmartLife network.
If the network has not been detected refer to step 3, otherwise continue onto step 4
3. On the Monitor go into Video Intercom > Cloud Intercom > Wifi Connection, and finally press “Valid”.
This will turn on AP mode, and the monitor will reboot, and once rebooted create the SmartLife hotspot.
4. Open the Click Smart+ app on your phone, press “Add Device”, go into “ESP” on the left hand side, and
select “Aperta IP PoE Monitor with App”.
5. Ensure that AP Mode is selected in the top right corner, and follow the onscreen instructions.
5. System Diagram Examples