Dahua VTO12 Series User manual

VTO12XX Series User's Manual
V1.2.0

i
Welcome
Thank you for purchasing our product!
This quick start guide is designed to be a reference tool for your system.
Please keep it well for future reference!

ii
Important Safeguards and Warnings
Please read the following safeguards and warnings carefully before using the product in
order to avoid damages and losses.
Note:
Do not expose the device to lampblack, steam or dust. Otherwise it may cause
fire or electric shock.
Do not install the device at position exposed to sunlight or in high temperature.
Temperature rise in device may cause fire.
Do not expose the device to humid environment. Otherwise it may cause fire.
The device must be installed on solid and flat surface in order to guarantee
safety under load and earthquake. Otherwise, it may cause device to fall off or
turnover.
Do not place the device on carpet or quilt.
Do not block air vent of the device or ventilation around the device. Otherwise,
temperature in device will rise and may cause fire.
Do not place any object on the device.
Do not disassemble the device without professional instruction.
Warning:
Please use battery properly to avoid fire, explosion and other dangers.
Please replace used battery with battery of the same type.
Do not use power line other than the one specified. Please use it properly.
Otherwise, it may cause fire or electric shock.
Special Announcement
This manual is for reference only.
All the designs and software here are subject to change without prior written
notice.
 All trademarks and registered trademarks are the properties of their respective
owners.
If there is any uncertainty or controversy, please refer to the final explanation of
us.
 Please visit our website for more information.

iii
Table of Contents
1Product Overview............................................................................................... 1
1.1 Model List........................................................................................................ 1
1.2 Structure......................................................................................................... 1
1.2.1 VTO1210A-X/VTO1220A...................................................................... 1
1.2.2 VTO1210B(W)-X/VTO1220B(W)........................................................... 6
1.3 VTO1210C-X ................................................................................................ 10
2Install VTO ....................................................................................................... 14
2.1 VTO1220A/VTO1210A-X.............................................................................. 14
2.1.1 Screw.................................................................................................. 14
2.1.2 Installation Steps................................................................................. 14
2.1.3 Wiring.................................................................................................. 15
2.2 VTO1210B(W)-X/VTO1220B(W)................................................................... 15
2.2.1 Screw.................................................................................................. 15
2.2.2 Installation Steps................................................................................. 16
2.2.3 Wiring.................................................................................................. 16
2.3 VTO1210C-X ................................................................................................ 17
2.3.1 Screw.................................................................................................. 17
2.3.2 Installation Steps................................................................................. 17
2.3.3 Wiring.................................................................................................. 17
3Debug VTO........................................................................................................ 1
3.1 Digital System................................................................................................. 1
3.1.1 System.................................................................................................. 1
3.1.2 Configure VTO...................................................................................... 2
3.1.3 Digital VTH............................................................................................ 4
3.1.4 Result Test............................................................................................ 4
3.2 Analog System................................................................................................ 4
3.2.1 System.................................................................................................. 4
3.2.2 Configure VTO...................................................................................... 5
3.2.3 Analog VTH........................................................................................... 7

iv
3.2.4................................................................................................................... 8
4Basic Functions.................................................................................................. 1
4.1 Call.................................................................................................................. 1
4.2 Modify Local Config......................................................................................... 1
4.2.1 Enter Project Settings Interface............................................................. 1
4.2.2 Modify IP, Gateway and Subnet Mask................................................... 1
4.2.3 Modify Volume Config........................................................................... 2
4.3 Issue Card....................................................................................................... 2
4.4 Password Function.......................................................................................... 2
4.4.1 Unlock from VTH and Center ................................................................ 2
4.4.2 Unlock from Local ................................................................................. 2
4.4.3 Unlock via IC card................................................................................. 3
4.5 VTO Web Function.......................................................................................... 3
4.5.1 Web Login............................................................................................. 3
5Web Function..................................................................................................... 4
5.1 Login............................................................................................................... 4
5.2 System Config................................................................................................. 4
5.2.1 Local Config.......................................................................................... 5
5.2.2 LAN Config ........................................................................................... 7
5.2.3 Indoor Manager..................................................................................... 7
5.2.4 Allocator Manager................................................................................. 9
5.2.5 Network Config ..................................................................................... 9
5.2.6 Video Set............................................................................................ 10
5.2.7 Change Password............................................................................... 11
5.2.8 User Manage ...................................................................................... 11
5.2.9 IPC Information................................................................................... 12
5.2.10 Publish Information.......................................................................... 12
5.3 Info Search.................................................................................................... 13
5.3.1 Call Record......................................................................................... 13
5.3.2 Alarm Record...................................................................................... 14

v
5.3.3 Swiping Card Record.......................................................................... 14
5.4 Status Statistics............................................................................................. 15
5.5 Logout........................................................................................................... 15
Appendix 1 Specifications ....................................................................................... 16

1
1 Product Overview
1.1 Model List
This manual is designed for multiple product models, please read and check carefully for
your product model and its functions.
Product Model
Housing
Material
Color
Unlock via
IC Card
Keyboard
Control Module
VTO1210A-X
Metal
Metal
grey
Support
Numeric
keyboard
Built-in
VTO1220A
Metal
Metal
grey
Support
Numeric
keyboard
Built-in
VTO1210B(W)-X
Fireproof
ABS
Black
Support
Touch
keyboard
Built-in
VTO1220B(W)
Fireproof
ABS
Black
Support
Touch
keyboard
Built-in
VTO1210C-X
Metal
Metal
grey
Support
Numeric
keyboard
Built-in
1.2 Structure
1.2.1 VTO1210A-X/VTO1220A
1.2.1.1 Front Panel
Plug to power, system boots up and wait for 1 minute, screen turns on. System enters
working interface, see Figure 1- 1 VTO1210A-X/VTO1220A.

2
Figure 1- 1 VTO1210A-X/VTO1220A
Please refer to the following sheet for detailed information.
SN
Name
Function
1
Logo
Decoration logo.
2
Photo Sensor
It can detect the environment light. It is a
compensation light option.
3
Compensation Light
It can compensate the camera light in
the low illumination environments.
4
Microphone
Audio input

3
5
Key Panel
1. Button.
a) Backspace function. It is to delete
the previous symbol.
b) Hang up function. It is to hang up
the call.
2. Number button. Input the number 0 to
9.
3. button. When you are using the
password to open the door. Press this
button once to begin input. After you
input the password, please press it again
to complete the operation.
4. Call button. After you input the
room number, press it to begin a dial up.
5. Call center button. Press it to
call the center directly.
6
Speaker
Output audio
7
Card Induction zone
Use the card to open the door.
8
LCD
Here you can view prompt information,
date, time and etc.
Note:
1. ―Call: Room No. + ↑ ‖. Please input the
room number first and then press the
button to dial；
2.‖Call Center: Press button‖. Please
press the button to call center.
3.―Password：+ password + ‖，
If you want to open the door via the
password, please press the button
and then input the room number and
password. Please press the button
to confirm.
9
Camera
It is to monitor the video of the door.

4
1.2.1.2 Rear Panel
Figure 1- 2 VTO1210-A-X/VTO1220A
Please refer to the following sheet for detailed information.
SN
Port Name
Function
1
Network Port
Connect to the RJ45 port.
2
Access Control Input
Port
Connect to signal from the door sensor,
door on/off signal.
3
Analog Signal Port
Connect to the analog signal of the

5
(VTO1210A-X only)
distributor.
corresponds
to
4
Vandal Proof Alarm
Button
It can generate an alarm when there is
a vandal operation.
5
RS422 Port
(Reserved)
Connect to RS422 or RS485
Communication Device.
or
6
Power Port
Connect to 12V DC.

6
7
Access Control
Output Port
Control NO/NC of door lock.
1.2.2 VTO1210B(W)-X/VTO1220B(W)
1.2.2.1 Front Panel
Plug to power, system boots up and wait for 1 minute, screen turns on. System enters
working interface, see Figure 1- 3 VTO1210B(W)-X/VTO1220B(W).

7
Figure 1- 3 VTO1210B(W)-X/VTO1220B(W)
Please refer to the following sheet for detailed information.
SN
Name
Function
1
Logo
Printed logo.
2
Microphone
Audio input
3
Compensation Light
It can compensate the camera light in
the low illumination environments.
4
Approaching
Induction
It can detect approaching body.
5
Speaker
Output audio

8
6
Key Panel
1. Button.
a) Backspace function. It is to delete
the previous symbol.
b) Hang up function. It is to hang up
the call.
2. Number button. Input the number 0 to
9.
3. button. When you are using the
password to open the door. Press this
button once to begin input. After you
input the password, please press it again
to complete the operation.
4. Call button. After you input the
room number, press it to begin a dial up.
5. Call center button. Press it to call
center directly.
7
Card Induction Zone
Use the card to open the door.
8
LCD
Here you can view prompt information,
date, time and etc.
Note:
1. ―Call: Room No. + ‖. Please input
the room number first and then press the
button to dial；
2.‖Call Center: Press button‖. Please
press the button to call center.
3.―Password：+ password + ‖，If
you want to open the door via the
password, please press the button
and then input the room number and
password. Please press the button
to confirm.
9
Camera
It is to monitor the video of the door.

9
1.2.2.2 Rear Panel
Figure 1- 4 VTO1210B(W)-X/VTO1220B(W) rear structure
Please refer to the following sheet for detailed information.
SN
Port Name
Function
1
Vandal Proof Alarm Button
It can generate an alarm when there is a vandal operation.
2
Network Port
Connect to the RJ45 port.
3
Access Control Input Port
Connect to signal from the door sensor, door on/off signal.
4
Power Port
Connect to 12V DC power.
5
Access Control Output Port
Open or close the NO/NC lock.

10
6
Analog Signal Port
Connect to the analog signal of the distributor.
7
RS485 Port
Connect to RS422 or RS484 communication device.
or
1.3 VTO1210C-X
1.3.1.1 Front Panel
Plug to power, system boots up and wait for 1 minute, screen turns on. System enters
working interface, see Figure 1- 5 VTO1210C-X.

11
Figure 1- 5 VTO1210C-X
Please refer to the following sheet for detailed information.
SN
Name
Function
1
Logo
Printed logo.
2
Microphone
Audio input
3
Compensation Light
It can compensate the camera light in
the low illumination environments.
4
Speaker
Output audio
5
Key Panel
1. Button.
c) Backspace function. It is to delete
the previous symbol.
d) Hang up function. It is to hang up
the call.
2. Number button. Input the number 0 to
9.

12
3. button. When you are using the
password to open the door. Press this
button once to begin input. After you
input the password, please press it again
to complete the operation.
4. Call button. After you input the
room number, press it to begin a dial up.
5. Call center button. Press it to call
center directly.
6. button: In contacts interface,
press these buttons to page up and
down. They can be customized for
special function.
6
Card Induction Zone
Use the card to open the door.
7
LCD
Here you can view prompt information,
date, time and etc.
Note:
1. ―Call: Room No. + ‖. Please input
the room number first and then press the
button to dial；
2.‖Call Center: Press button‖. Please
press the button to call center.
3.―Password：+ password + ‖，If
you want to open the door via the
password, please press the button
and then input the room number and
password. Please press the button
to confirm.
8
Camera
It is to monitor the video of the door.
1.3.1.2 Rear Panel
VTO1210C-X rear panel is the same with VTO1210B(W)-X/VTO1220B(W), therefore

13
please refer to Ch 1.2.2.2.

14
2 Install VTO
Unit VTO on-site installation includes: wall embedded installation, door embedded
installation (with box/without box), standalone installation.
This chapter will introduce installation of VTO1220A/VTO1210A-X series,
VTO1210B(W)-X/VTO1220B(W) series and VTO1210C-X series.
2.1 VTO1220A/VTO1210A-X
2.1.1 Screw
Component
Screw No
Illustration
Quantity
ST3×18 Cross recessed pan head
tapping screws –white alloy
Screw a
6
M3×16 Cross slot recessed pan head
screws- zinc black
Screw b
1
White expansion pipe ￠6×30mm
None
6
2.1.2 Installation Steps
Step 1. Fix metal housing on wall with screw a.
Step 2. Fix device on the metal housing with screw b.