Scolmore ESP Aperta A1IPVDS User manual

A1IPVDS
Quick Start Guide
The latest product manuals and software is available online:
https://www.espuk.com/technical_support
REV: D23
Aperta IP PoE Single Way Outdoor Station IP65 HD
with Proximity Reader

1. Installation
Connect the Door Station to a switch/network or alternatively directly to a Monitor using the RJ45 port [1].
If the connected network does not support PoE, then DC12V1A needs to be applied to the 12V & GND
terminals [2].
*All system cabling has been tested with Cat5E UTP PVC Cable.
**Maximum distance of 100m to PoE switch is supported.
[1]
Alternative power connections
[2]
GND
12V
485A
485B
GND
RS485
NO12V+
NC
COM
NO
CTL
DET
GND
(Red)
(Orange)
(Green)
(Yellow)
(Brown)
(White)
(Black)
IP/PoE connection
Fail Secure Lock (+)
Video Door Station
Lock Connections
Exit button
Sensor Ground

2. Single Device Installation
1. Ensure both the Door Station & Compatible monitor are connected VIA a PoE Switch or Directly
connected VIA an Ethernet cable.
2. Factory reset both Door Station & Monitor:
A. Door Station Reset - Press call button for 60 Seconds, when a ringtone plays it has successfully
reset.
B. Monitor Reset - Go to “System Settings” type in “666666” & “OK”, click on “System Reset”, the
monitor will then restart.
3. After both devices have restarted the 2 devices will now be connected to each other.
3. Multi Device Installation
1. Ensure only the first Door Station & Compatible monitor are connected VIA a PoE Switch or Directly
connected VIA Ethernet cable.
2. Factory reset both Door Station & Monitor
A. Door Station Reset - Press call button for 60 Seconds, when a ringtone plays it has successfully
reset.
B. Monitor Reset - Go to “System Settings” type in “666666” & “OK”, click on “System Reset”, the
monitor will then restart.
Note: If a device has not been configured it does not need to be reset
3. After both devices have restarted the 2 devices will now be connected to each other.
4. Ensure the master monitor is set to Villa; please refer to step in the A1IPMW/B Quick Start Guide.
5. Programming the first Door Station:
On the monitor go to “System Settings”, type in “666666” & “OK”, and click on “Door”.
Once on the “Door” page, at the top select “Villa”, type in 01 for the Ext. Field, and complete the rest of
the fields to your requirements, and finally press “OK”.
6. Programming an additional Door Station:
Connect the next Villa Door Station, and then on the monitor go to “System Settings”, type in “666666” &
“OK”, and click on “Door”.
Once on the “Door” page, at the top select “Villa”, type in the next available address for the Ext. Field,
and complete the rest of the fields to your requirements, and finally press “OK”.
7. Add the Master monitor:
Once all Outdoor Stations have been configured, on the monitor that will serve as the master monitor, go
to “System Settings”, type in “666666” and the press “OK”.
Click on “Extension”, and change the extention to 01, and press “OK”.
8. Adding multiple monitors:
On the additional monitor(s) go to “System Settings”, type in “666666” and the press “OK”.
Click on “Extension”, and change the extention to a number between 02~06, and press “OK”.
Note:
Do not use an extention number that has already been used, and ensure that there is always monitor that has the extension 01.
A Maximum of 2 Outdoor Stations on a single system is recommended. If more are required, please contact ESP Technical for further information

Contact Details
Elite Security Products UK, Unit 7 Target Park, Shawbank Road, Lakeside, Redditch, Worcestershire, B98 8YN
Tel: [phone] Fax: [phone] Email: [email protected]
Registered in England, Company Registration Number: 02769392, VAT Registration: GB614686525
For more product information please visit www.espuk.com E&OE - Errors and Omissions Excepted. D23
4. Public PIN Code
1. Entering administration mode:
When in standy, press [ + Admin Passcode + #], if the doorbell bleeps twice, and the call button is
slowly flashing, you have successfully entered administration mode.
2. Setting the Public Unlock PIN:
Once in Administration Mode press;
[0+ 11+ #+ New PIN + #+ New PIN + #].
If the Door Station bleeps twice the PIN has been set successfully.
3. To Exit press or wait 30 seconds until the Door Station bleeps 3 times.
4. Using the Public Unlock PIN:
When in standby enter the New Public Unlock PIN set in step 3, and press “#”.The Door Station will
announce “The door is open, please come in”, if the incorrect PIN is entered it will bleep 4 times.
Note:
Default Admin Passcode is 666666.
Public PIN code must be 6 digits
5. User Cards / Fobs
Add User Cards / Fobs
1. In standby mode, swipe the “Add Fob” 3 times within 15 seconds.
The call button will rapidly flash to indicate it is in the add card mode.
2. Swipe the unregistered fob on the RFID read area, if the Door Station bleeps twice, this means that fob
has been added successfully.
3. Once all cards have been added, finally swipe the add fob a final time to exit the add fob mode.
Delete User Cards / Fobs
1. In standby mode, swipe the Delete fob” 3 times within 15 seconds.
The call button will rapidly flash to indicate it is in the delete fob mode.
2. Swipe the registered fob in the RFID read area, if the Door Station bleeps twice, this means that the fob
has been deleted successfully.
3. Once all cards have been added, finally swipe the delete fob a final time to exit the delete fob mode.
Note:
Add cards are denoted by a “+” on the card, and Delete Cards are denoted by a “-” on the card.
Only 13.56 MHz Fob/Cards are supported.