Zamel VP-819B User manual

VIDEO ENTRY PHONE DISPLAY
VP-819B / VP-819W
Thank you for buying this product from Zamel.
Zamel shall not accept any liability for any results of damage
and / or accidents caused by non-intended use of the product.
Before attempting to install this product, please read and understand
the entire Operating Manual to comply with the intended use.
Do not open or tamper with the product without prior authorization.
Otherwise your warranty rights for this product will be void.

2
SAFETY
• Always follow this Manual for your safety and to prevent damage to the product.
• Do not connect more than one load to a single power outlet at a time. Risk
of overheating the wiring or re!
• Do not connect or interface this device with incompatible products. Otherwise
there is a risk of an electrical short circuit, resulting in damage to this product.
• Protect the display main board and screen from deformation by any stress.
Do not apply heavy loads. Otherwise there is a risk of re.
• Do not clean the display screen or housing with water or detergents. Risk
of damage to the display housing and/or screen, electrical short circuit, and/or
re! Clean the display with a soft, dry cloth made of cotton or microbre. This will
prevent scratching the display screen. Never use toilet paper or tissues.
• Do not install in a highly humid indoor environment. Risk of electrical short circuit
and re!
• Disconnect the power cord from the mains by holding the plug and not the cable.
Damage to the power cord cable may result in an electric short circuit or a re.
• Do not plug the power cord into the mains with wet hands. Electrocution hazard!
• Do not attempt to disassemble, repair or alter this product on your own. Risk
of electrocution, damage to the product and/or re!
• Do not install a current breaker on the mains connection of the device.
Electrocution hazard!
PRODUCT DESCRIPTION
• 7” colour LCD touch screen
• 4-core wiring
• Intuitive interface
• Internal calls (display-to-display
intercom mode)
• Public Address mode
• Gate and wicket opening control
• Supports up to two CCTV feeds
• Supports up to two entrance panels
• On-demand video feed monitoring
from entrance panels and all
• connected CCTV cameras
• Two-way voice communication
• High display screen resolution:
800 x 480
• Clear voice handset-free device
• Language selection
• Intuitive buttons
• 10-step voice volume control
• 10-step brightness, contrast
and saturation control
• 10-step ringtone volume control
• 12 polyphonic ringtones
TECHNICAL DATA
• Operating temperature: -30°C to +60°C
• Supply voltage: 110-240 V AC
/ 50-60 Hz; 14.5 V DC / 0.8 A
• Power input: 7 W (max); 0.7 W
(standby)
• Operating RH: 0% to 95%
• Display dimensions: 208 x 115 x 25 mm
• Weight: 430 g
WIRING PROFILE
• ≤ 50 m (4 x 0.5 mm2)
• ≤ 75 m (4 x 0.75 mm2)
• ≤ 100 m (4 x 1.0 mm2)
PRODUCT COMPONENTS
• 1 x Display unit
• 1 x Operating Manual
• 1 x Base stand
• 2 x Wall plugs
• 2 x M4 x 30 screws
• 2 x 5-pin male connector
• 1 x 4-pin male connector
• 1 x 4-pin male connector

3
WIRING CONNECTION DIAGRAM
AD: Audio
VD: Video
PWR: Power
GND: Ground
DATA: Data communication
CCTV: CCTV feed in
KEY1/KEY2: Control voltage
J4
J4
J4
J4
ROOM 1
ROOM 2
ROOM 3
ROOM 4
ELECTRIC
CATCH 2
ELECTRIC
CATCH 1
DISPLAY 1
DISPLAY 2

4
Note:
(a) Wiring connection diagram for an entrance panel with electric catch no. 2 + extra external
power supply.
(b) Wiring connection diagram for electric catch no. 1 with the display output power
(GND and KEY1 contacts).
(c) External power supply port J4 (optional)
(d) Wiring connection diagram for the NC06 gate control module (Connector P3 GND
and DATA to NC06; COM NO/NC to gate control)
AD: Audio
VD: Video
PWR: Power
GND: Ground
DATA: Data communication
CCTV: CCTV feed in
KEY1/KEY2: Control voltage
J4
J4
J4
J4
BLUE
YELLOW
WHITE
RED
ROOM 1
ROOM 2
ROOM 3
ROOM 4
ELECTRIC
CATCH 1
DISPLAY 1

5
• The second and each additional display may only output the video feeds from
the cameras to which they are connected.
• All displays can output the video feed of a CCTV camera connected
to the entrance panel port.
AD: Audio
VD: Video
PWR: Power
GND: Ground
DATA: Data communication
CCTV: CCTV feed in
KEY1/KEY2: Control voltage
J4
J4
J4
J4
ROOM 1
ROOM 2
ROOM 3
ROOM 4
DISPLAY 1

6
SYSTEM CONFIGURATION
The system can be installed in one of the congurations shown
in the diagrams below:
• 2 gate entrance panels + 4 displays + 2 CCTV cameras for each display
• 1 gate entrance panel + 1 CCTV camera + 4 displays + 2 CCTV cameras
for each display
MAIN DISPLAY
DOOR 1
DOOR 2
DISPLAY 2 DISPLAY 3 DISPLAY 4
CAMERA 1 CAMERA 1 CAMERA 1 CAMERA 1
CAMERA 2 CAMERA 2 CAMERA 2 CAMERA 2
1 stacja bramowa + 1 kamera CCTV + 4 wideo monitory + 2 kamery CCTV do
każdego monitora
DRZWI 1
KAMERA1
KAMERA2
KAMERA1 KAMERA1 KAMERA1
KAMERA2 KAMERA2 KAMERA2
DRZWI 2
6
DRZWI 1
KAMERA1
KAMERA2
KAMERA1 KAMERA1 KAMERA1
KAMERA2 KAMERA2 KAMERA2
KAMERA3
MONITOR
GLÓWNY MONITOR 4
MONITOR 3MONITOR 2
MONITOR
GLÓWNY MONITOR 4
MONITOR 3MONITOR 2
2 stacje bramowe + 4 wideo monitory + 2 kamery CCTV do każdego monitora
Istnieje możliwość zastosowania jednej z konfiguracji systemu zgodnie ze
schematami poniżej:
Konfiguracja systemu
MAIN DISPLAY
CAMERA 3
DOOR 1
DISPLAY 2 DISPLAY 3 DISPLAY 4
CAMERA 1 CAMERA 1 CAMERA 1 CAMERA 1
CAMERA 2 CAMERA 2 CAMERA 2 CAMERA 2

7
PRODUCT DESCRIPTION
1. Enter Menu / Conrm
2. Down arrow button: Select / Adjust
3. Up arrow button: Select / Adjust
4. Back / Hang Up
5. LCD
6. LED indicator
7. Answer / Call
8. Unlock
9. Open gate
10. Video feed display
11. Power On/Off switch
INSTALLING THE SYSTEM
1. Use the wiring connection diagram for the chosen system conguration
and verify that all wiring connections are correct.
2. Choose a suitable location in which to install the display unit. An installation
height between 1.5 and 1.6 m above the ground is recommended.
3. Verify that the power supply voltage is OFF before wiring the device.
4. Mount the back frame on the wall at the installation location.
5. Connect the wiring to the terminals, see the wiring connection diagram
for the chosen system conguration.
6. Install the display unit on the back frame.
7. Switch on the supply voltage of the device when completely installed.
1
2
3
4
5
6
7
8
9
10
11

8
WIRING SPECIFICATIONS
The system supports two electric catch release congurations: with the open
command sent by (i) an entrance panel or (ii) a system display (the display open
command output wire must have the shield connected to earth).
If the open command is sent by an entrance panel, use this wiring specication:
• If the entrance panel is < 30 m away from the video entry phone display,
use YTDYw 4 x 0.5 mm2wiring.
ENTRANCE PANEL
1
2
3
4
1
2
3
4
RED
BLUE
YELLOW
WHITE
RED
BLUE
YELLOW
WHITE
GREEN
BROWN
• If the entrance panel is > 30 m away from the video entry phone display,
use YTDYw 4 x 0.5 mm2wiring.
ENTRANCE PANEL
ELECTRIC
CATCH
1
2
3
4
1
2
3
4
RED
BLUE
YELLOW
WHITE
RED
BLUE
YELLOW
WHITE
GREEN
BROWN
If the open command is sent by a display, use this wiring specication:
• If the entrance panel is < 30 m away from the video entry phone display,
use YTDYw 6 x 0.5 mm2wiring.
ENTRANCE PANEL
ELECTRIC CATCH
RED
BLUE
YELLOW
WHITE
BROWN
RED
BLUE
YELLOW
WHITE
BLACK
GREEN
• If the entrance panel is < 30 m away from the video entry phone display,
use YTDYw 6 x 0.8 mm2wiring.
ENTRANCE PANEL
ELECTRIC CATCH
RED
BLUE
YELLOW
WHITE
BROWN
GREEN
RED
BLUE
YELLOW
WHITE
BLACK
GREEN
DISPLAY
DISPLAY
DISPLAY
DISPLAY
ELECTRIC
CATCH
GREEN

9
ANSWERING AN ENTRANCE PANEL CALL
When a visitor presses the Call button on the entrance panel, all connected indoor
displays will sound the call chime at the same time as the INCOMING CALL
message on each display screen.
Touch the icon to answer the call. Touch again to send the calling entrance
panel camera feed to all other displays. If the call is not answered by the time
the call chime stops, the display will enter the standby mode. Touch the icon
to release the electric catch of the calling entrance panel during the call. The display
will show DOOR OPEN. Touch the icon to open the gate. The display will show
GATE OPEN. If another user calls during your call, the display will show VISITOR
AT DOOR 2. Touch the icon to answer and switch to the second call.
Note: Touch and hold the icon during an entrance call or an internal call
(display-to-display intercom mode) to mute your microphone. The display will show
MUTE. Touch and hold again to unmute your microphone, which the display will
conrm with SPEAK. Operating a gate requires the NC06 gate control module
in the system.
VIDEO FEED MONITORING
With the display on standby, touch to monitor the video feed from entrance
panel no. 1. Touch again to switch to the next video feed.
The CCTV camera video feeds can only be monitored this way if the Port 4 status
is Enabled (see Table SYSTEM SETTINGS, item 10).
Touch to start a voice call with the visitor at the entrance panel from which you
are monitoring the video feed. Touch to unlock the door of the same entrance
panel.
When monitoring the video feed from Door1 / Door2 / Video1 / Video2, touch and
hold to change the screen aspect from 16:9 to 4:3.
PUBLIC ADDRESS MODE
The Public Address mode allows you to speak through all displays connected
to the video entry phone system. When the display is on standby, touch and hold
on the screen. The PUBLIC ADDRESS CALL message will be displayed.
All other displays in the system will display PUBLIC ADDRESS. You can now
speak and be received by other displays in the system. Touch to exit the public
address mode.

10
INTERNAL CALLS (DISPLAY-TO-DISPLAY INTERCOM MODE)
The intercom mode allows two-way voice calls between two specic displays
in the video entry phone system. Touch on the display on standby to call another
display in the system. If you have more than 2 displays in the video entry phone
system, choose the display you wish to call with or . Next, touch
to conrm and make the call. The user at the display being called can touch
to answer the call or to reject the call.
DISPLAY SOUND VOLUME / BRIGHTNESS / COLOUR
/ CONTRAST / IMAGE TYPE CONTROL
Touch or in the monitoring, incoming call, voice call, intercom, or public
address mode to open the sound volume menu. Next, touch to open
the Volume / Brightness / Colour / Contrast / Image Type menu. Operate
the controls with or .
DO NOT DISTURB MODE
You can enable or disable the DO NOT DISTURB mode in the display System
Settings menu. Touch and hold to enable or disable this mode.
DISPLAY MICROPHONE MONITORING
With the display on standby, touch and hold to start listening through
the microphone of another display in the voice entry phone system. If you have
more than 2 displays in the video entry phone system, choose the display you wish
to listen to by touching or and conrm with .
Note:
a) The user of the display that is listening will hear everything that the microphone
of the display being listened to captures. The display being listened to will not
output the sounds captured by the microphone of the display which is listening.
b) If you have more than 2 displays in the video entry phone system, verify that
the remote listening mode is enabled in the display to which you want to listen.
Go to System Settings and verify that Can Be Monitored is set to Enable.

11
SYSTEM SETTINGS
With the display on standby, touch and open the System Settings menu.
Item System functions Options Note
1 LANGUAGE Default setting: PL (Polish) (optional: EN for English).
2RING TIME Default setting: 30 s (10 to 60 s, adjustable in 5 s steps).
3RING VOLUME Default setting: 0.7, adjustable in a 01-10 range. (00)
mutes the sound.
4DO NOT DISTURB MODE
The mode is disabled by default during a call from
an entrance panel, display-to-display intercom (internal)
calls and the public address mode. The LED will ash
if this mode is enabled.
5MONITORING
The mode is disabled by default. The monitoring
of remote display microphones can be enabled
in the System Settings.
6 MONITOR UNLOCK
Touch to unlock the electric catch linked
to the entrance panel. Touch to open the gate linked
to the entrance panel.
7DEVICE ADDRESS Room 1 / 2 / 3 / 4
Choose ROOM 1
on the display that should
be the main (master)
display of the system.
The setting will be yellow
if the same device address
is set in two displays in the
video entry phone system.
8RING TYPE
Door 1 Ring Type Formats the embedded
ash memory of this display.
Door 2 Ring Type Formats the embedded
ash memory of this display.
Intercomm Ring Type Formats the embedded
ash memory of this display.
9RING REPEAT
ENABLE The ringtone will sound
repeatedly.
DISABLE The ringtone will sound
once.
10 PORT STATE None / CCTV1 / CCTV1&2
11 RESTORE DEFAULT Restores the display unit settings to default values.

12
ADVANCED SETTINGS
The Advanced Settings can be accessed by pressing and holding while
powering on the display. The Advances Settings include:
• Door unlock time
1-10; 20, 30, 40, 50, 60, 70, 80, 90, 99 s
• Gate status
Normally open electric catch contact (NO)
Normally closed electric catch contact (NC)
• Gate unlock time
0.2, 0.5, 1-5 s
• System type
Single-family
Multi-family
WARRANTY
24-month commercial warranty by the manufacturer
Reseller’s stamp and signature
with date of sale
1. ZAMEL Sp. z o.o. Gives a 24-month warranty for
the goods it sells.
2. The warranty given by ZAMEL Sp. z o.o. does not cover:
a) mechanical damage caused by transport,
loading/unloading or other circumstances;
b) damage caused by improper installation or operation
of the goods manufactured by ZAMEL Sp. z o.o.;
c) damage caused by any modications made by the BUYER
or any third party to the sold goods or to the equipment
required for the proper functioning of the sold goods;
d) damage caused by any force majeure
event or another fortuitous event beyond
any reasonable control of ZAMEL Sp. z o.o.;
e) the power supply (batteries) included (if any) with the
device as sold.
3. The BUYER shall make all warranty claims in writing at the point of sale or to ZAMEL Sp. z o.o.
4. ZAMEL Sp. z o.o. will examine each warranty claim as regulated by the applicable provisions of the Polish law.
5. The form of warranty claim resolution, i.e. replacement, repair or refund of the price of purchase, shall
be decided by ZAMEL Sp. z o.o.
6. This warranty does not exclude, limit or suspend any rights of the BUYER arising from the statutory
or regulatory laws concerning implied warranty for defects of sold goods.