SCORPION 10" PLUS User manual

SCORPION " PLUS
Rugged Tablet PC
QUICK-START GUIDE
EN
For more information about the product and a detailed
description, please visit:
https://www.scorpion-rugged.de/en/products/scorpion-10-plus/
BRESSNER Technology GmbH
Industriestrasse 51
82194 Groebenzell
Phone: [phone]
E-mail: [e-mail]

SCOPE OF DELIVERY
This package includes:
1. SCORPION 10" PLUS - Rugged Tablet
2. 3-in-1 AC power adapter USB 5V/3A (EU, UK, US)
3. USB charging cable (Micro USB Male to USB A-Male)
4. Carrying strap
5. USB OTG cable (Micro USB Male to USB A-Female)
6. Hand strap
EN
3
1
5
4
6
2

1. Kensington lock
2. Audio-Out 3,5mm
3. Mini-HDMI
4. Micro USB OTG/Power
5. USB 2.0
6. DC input
7. Volume -
8. Volume +
9. Programmable button P
10. Power On/O
11. Scan button F
12. 2MP front camera
13. Corning® Gorilla® Glass
14. Docking port
15. LAN
16. DB-9 serial COM
17. Speaker
18. 5MP rear camera
19. Barcode scanner (optional)
20. Replaceable battery
(SIM and SD card slot are located
below the battery)
21. Fingerprint sensor
FEATURES
Version 1.03
Technical specifications are subject to change

BATTERY REMOVAL
EN
1
Please follow the instructions, when removing battery!
2
3
Step 1
Carefully remove the six screws on the back of the device
with a flat-head screwdriver.
Step 2
Carefully remove the battery cover and then unlock the two
latches by sliding them apart as shown in the illustration.
Step 3
Carefully remove the battery, insert a spare battery and
reverse the steps to reseal the tablet.

How to insert the SIM card(s) correctly:
SIM CARD
Version 1.03
Technical specifications are subject to change
In order to reach the SIM card slot the device’s battery must be removed first (please follow the instructions on the le side). Aer
removing the battery, insert the micro SIM card into its designated slot (see illustration), until it locks in. Please make sure that the
gold contacts of the SIM card are on the bottom side. Aerwards repeat step 1 to 3 on the le side in reverse order to reseal the
device properly.

SCANNER SETUP
EN
Honeywell 2D scanner N3680 (optional)
Datasheet
http://bit.ly/n3680-datasheet-en
Technical Details
The N3680 barcode scan engine is a revolutionary, fully decoded,
compact 2D imager from Honeywell. It inherits the legendary Adaptus™
6.0 decoding performance in our most compact design. The N3680 2D
imager represents a fine balance between size, performance and ease
of integration – ensuring an excellent end-user experience.
Not only does the N3680 2D imager support a wide variety of
symbologies, including 1D, 2D and PDF417 barcodes, it also includes
advanced features that support reading poorly printed barcodes and
can even read barcodes directly from smartphone screens. This makes
the N3680 2D imager a perfect choice for reading mobile coupons and
loyalty cards, mobile ticketing, paperless boarding passes and barcode
payment systems for mobile wallet applications.
Operation and configuration of the scanner
The user manual for the Honeywell scanner series N36XX provides a lot of information about the functionality and configuration
of the scanner module. Use the included programming codes to transfer the desired configuration settings to the scanner. These
programming codes can be scanned directly from the User’s Guide. To do this, follow the instructions in each chapter. At the end
of the manual you will also find a “Programming Chart” with the numbers 0-9 to be able to scan sequences of numbers if required.
Attention - The configuration data is stored directly in the scanner module and not in the operating system. Consequently, you can
use this type of scanner programming regardless of the installed operating system.
Examples of typical configuration settings:
Setting the language of the keyboard layout, activating/deactivating code types, configuring prefixes and suixes, activating inverse
codes, adjusting the position and size of the scanned section, loading factory defaults, etc.
EZConfig for Windows
For extensive and complex configurations please install the utility “EZConfig” from Honeywell. This utility is a browser-based
interface for reading, editing and restoring scanner configuration data. It also allows you to save a complete configuration as a file
(*.exm). This can then be transferred to the scanner of another device via EZConfig. Android devices, on the other hand, have a pre-
installed scanner app for setting up the most frequently used scanner configurations.
If you still need help setting up the scanner please contact our support: [phone] - 44
User’s Guide
http://bit.ly/n36xx-user-guide-rev-b
EZConfig - Setup
http://bit.ly/ezconfig-setup
EZConfig - Tutorial
http://bit.ly/ezconfig-tutorial

FAQ
Frequently asked questions
Version 1.03
Technical specifications are subject to change
What should I do if the device or the scope of delivery does not meet my order or if individual components /
accessories are missing?
If you find that your order is incomplete or even faulty, our in-house support department will gladly attend to you. If you need
help or assistance, please fill out the support form on our website to open a support case:
https://www.bressner.de/en/support-en/
Alternatively, the form can also be completed as a PDF file and faxed to the following number: [phone]
You can also contact our technical support on weekdays from 8AM - 5PM by phone: [phone] - 44
What do I do if the device or individual components / accessories are defective?
In case of a defect in equipment, individual components or the accessories supplied, a return shipment or repair can be arranged.
BRESSNER Technology provides its own RMA form for this purpose. Please read the instructions on our website regarding the RMA
procedure carefully before filling out the form and returning it.
You can find the form on our website at: https://www.bressner.de/en/rma/
You can also contact our RMA department on weekdays from 8AM - 5PM by phone: [phone] - 24
Where do I find my Windows license key / license sticker?
For systems with replaceable batteries, the sticker with the license key is located in the battery compartment. For systems with
a permanently installed battery, the sticker is on the back of the device. In special cases there may be no license sticker at all, in
which case the license key is rooted in the BIOS (OEM 3.0 activation).
I only see a small sticker, but not the license key?
In this case it is the ePKEA version of the license sticker, which means the Bressner OEM product key is integrated into the image.
The key itself is not visible to the user (in plain text).
The Windows setup (OOBE) asks for a license key. How can I activate Windows?
Please skip this step without entering a key, the Windows product key was already stored by us in the installation. When the OOBE
is completed and an internet connection is established for the first time, Windows 10 activates automatically within a few minutes.
Important information about Windows 10 IoT Enterprise LTSB 2016 (V1607) / LTSC 2019 (V1809)
Please read and observe the following instructions concerning the operating system(s):
• The LTSB / LTSC versions deliberately do not receive any feature updates, the original versions are always retained.
▫Avoidance of lengthy update processes, faulty updates or incompatibilities with new versions
▫Secure operation, since security updates and patches are performed via Windows update or manual installation
▫Soware update from LTSB/LTSC to standard Win10 version not possible (only by new installation with new licensing)
• 10 years guaranteed support by Microso from date of introduction
• Full driver and soware compatibility (except UWP apps) with all popular Windows 10 versions (Home/Pro/Enterprise)
• Domain integration possible
• Slim basic installation without superfluous add-ons
• Systems can be used worldwide (special regulations of dierent countries do not apply to IoT Embedded Licensing)
• Low-cost licensing model in three price levels, depending on processor performance (Entry, Value, High-End)
• ATTENTION: The LTSB/LTSC versions deliberately do not contain a Microso Store andthe installation of Microso (UWP) apps
is not possible. The only exception is the Microso CameraApp, which was preinstalled on the device by Bressner Technology
in order to be able to use the camera(s). Windows 10-compatible programs, on the other hand, can be installed with no issue
(examples for browsers: Microso Edge Browser, IE11, Firefox, Chrome, Opera, etc.)
• Systems with IoT Embedded Licensing are not covered by support contracts with Microso (Enterprise Licensing)

SAFETY INSTRUCTIONS
Please read and observe carefully before using!
Environment:
Protect the device from temperatures outside the specified range. The device is protected against spray water but
must not be submerged in water or be exposed to water jets. Do not expose the unit to strong magnetic fields or
strong static electricity. Once water or liquid has entered the unit, turn it o and do not use until it is dried. Have it
checked by a qualified specialist.
Safety in operation:
Do not drop the device. Do not bend or twist it. This may result in a breakage of the display glass or of circuit
boards and mechanical parts. To avoid hearing damage, listen to music via headphones at a moderate volume
and never place the speaker outputs directly in front of your ear. Keep packaging materials and small parts away
from children. There is a danger of suocation. Never open the case of the appliance or the charger (risk of electric
shock, short-circuit and fire). Do not put objects through slots or openings on the appliance or charger (risk of
electric shock, short circuit, and fire). Do not attempt to open the unit, the unit may be destroyed and you will lose
warranty.
Cleaning:
Never clean the surface of the appliance with solvents, detergents or other chemical products. Use a so, dry cloth
instead.
Power supply:
Always use the original charger or one with suitable current and voltage rating to prevent damage to the device.
If you use an universal charger, consider the polarity of the charger as well as the current and the voltage rating.
Do not unplug the charger from the wall outlet by pulling the cable. Do not use chargers with damaged cables or
plugs.
Disposal:
Dispose used electronic equipment at the appropriate collection points. Please note that your device has a battery
and therefore it must not be disposed with normal household waste. Please consult your local or municipal
authorities for the correct disposal route of your device and battery.
Battery:
Batteries are wearing parts whose life cycle depends on handling.
Please also note the following:
• Fully charge the battery every six months
• Avoid exposing the device or the battery to excessive heat
• Do not expose the battery to mechanical stress
• Do not damage batteries with sharp or pointed objects
• Do not throw batteries into fire - they may explode
• Do not pour any liquids over the battery
• Avoid short-circuiting the battery, as it may result in overheating and ignition of the battery
• If liquid leaks from the battery and comes into contact with the eyes or skin, rinse immediately with clear water
and seek medical advice
• Incorrect replacement of the battery may result in a risk of explosion
• Replace battery only by the same or an equivalent type recommended by the manufacturer
• Please do not dispose used batteries with household waste. Use the service of specialist shops that carry out
the exchange.
EN