SCORPION 10X PRO User manual

QUICK-START GUIDE
EN
BRESSNER Technology GmbH
Industriestrasse 51
82194 Groebenzell
Phone: [phone]
E-Mail: [e-mail]
SCORPION 10X PRO
Rugged Android Tablet Device

OVERVIEW
EN
Package content:
• 1 x SCORPION 10X PRO
• 1 x power adapter (19V/45W)
1. Mic
2. LED indicator
3. Light sensor
4. 2MP IR camera (support Windows hello)
5. Touch Screen
6. Power on/o button
7. Programmable Button (2D Scanner)
8. Programmable Button
9. Volume down
10. Volume up
11. Touch modus switch
12. Home
13. Speaker

OVERVIEW
Version 1.00
Technical specifications are subject to change
14. Bumper protector
15. Fan cover
16. Ventilation
17. Dummy cover of peripheral kits
18. 8MP rear camera
19. Stylus
20. Batttery box
21. Docking connector
22. Access cover for MicroSD, and expansion GPS antenna
23. Access cover for HDMI, audio jack, USB 3.0 and charging connector
24. Service door (access to Nano SIM, SSD card, WIFI card, and LTE card)

CHARGING
EN
1. Power-on/power-o
When the tablet is shipped from the factory, the battery pack is in shipping mode for reducing battery consumption during ship-
ment. You must take the battery pack out of shipping mode before the battery pack can be charged and used.
To release the battery from shipping mode, please follow the steps:
Fully charge the battery when you charge for the first time!
Pry open the rubber cover protecting the charging port and plug in the charging cable supplied with the tablet.

CHARGING
Version 1.00
Technical specifications are subject to change
Press the power button for 1 second to turn on the system. The battery is released from shipping mode aer powering on the
tablet. If you want to power o the tablet, long press the power button for 4 seconds.
Note: For the best touch performance, remove the protective plastic overlay from the LCD screen by peeling it away from one of
the corners. Be sure to use a so pointing device or finger tip to avoid scratching the screen during normal use.

BATTERY
EN
2. Replacing the battery
You can replace the battery either when the tablet is turned o or when the tablet is still running on battery power. Changing a
tablet battery without powering o the tablet is called “hot swapping”.
To hot swap the battery, please follow the steps:
• Press the “Home” button of the tablet for two seconds to enter hot swapping mode, the display will get dimmer.
• The LED indicator starts to blink and you will hear the beeping sound. This is the time to replace the battery. You have four
minutes to hot swap the battery.
NOTE: The system will remind you aer three minutes by rapid beeping sound. If you do not insert the charged battery within four
minutes, the tablet will turn o automatically.
Place the tablet face down on a flat surface. Next, slide the small latch down first then slide the big latch le as shown to unlock
the battery cover.
Place a coin or your fingernails at the battery cover notch and gently li the battery box to release it from the tablet.

SERVICE DOOR
Version 1.00
Technical specifications are subject to change
Remove the screws (x4) and rubber pads (x4)
of the service door.
Gently li the service door.
A swap battery is attached to the service door. Disconnect the
connector from the motherboard as the picture shown.
Fully release the service door from the system.
2. Replacing the battery

SIM CARD
EN
4. Installing SIM Card
Remove the screws (x4) and rubber pads (x4) of the service door.
Gently li the service door and be careful not to pull o the
cables connecting to the motherboard.
With the SIM card’s gold contacts
facing down and its cut-o corner
facing in, insert the SIM card all the
way into the SIM card slot. Then
push the SIM card in until it clicks
into place.
Attach the rubber pad on the rear of the SIM card to ensure that
the SIM card fits securely into the slot.
rubber pad
To install the SIM card, you need to remove the SSD card first by
removing the screw (x1).

PERIPHERAL KITS
Version 1.00
Technical specifications are subject to change
5. Installing peripheral kits
You can expand the capabilities of tablet by connecting the peripheral devices: 2D scanner kit, Long distance 2D scanner kit, COM
kit, LAN kit, and USB kit.
Connect the 2D scanner module to the FPC connector on the tablet, then attach the module in place and fasten the screws (x2)
to secure it.
scanner connecter FPC connector
To install the 2D scanner kit, remove the screws (x2) and rubber pads (x2) to release the dummy cover first.

PERIPHERAL KITS
EN
Attach the 2D scanner cover and fasten the screws (x2). Last, put on the rubber pads (x2).
COM, LAN, and USB kits installation steps are the
same as 2D scanner kit, but the slight dierence is
you need to place a foam tape pad under the FPC
connector on the tablet before connecting the kits.
This will ensure the kits can be easily connected to
the FPC connector.
COM kit
LAN kit
USB kit
Adjust the height dierence
between dierent kits by placing
a foam tape pad here.