Scott Aerator AquaSweep User manual

We at Scott Aerator thank you for your purchase. It is our goal to ensure that you are completely
satised with your new AquaSweep and that it continues to operate smoothly for many years
to come. Please take a few moments to read through this document for proper assembly,
installation and maintenance to maximize the operating life of the unit.
This Kit Includes
1 - AQUASWEEP HOUSING
1 - OSCILLATOR ASSEMBLY
1 - DOCK PLATE
1 - STAINLESS STEEL BASKET
1 - PACKET OF LUBRICATING COMPOUND
2 - THUMB SCREWS
3 - SMALL SELF TAPPING SCREWS
4 - LARGE SELF TAPPING SCREWS
Tools Needed
ONE 3/8" WRENCH OR SOCKET SCREWDRIVER
ONE PHILLIPS STYLE SCREW DRIVER
TWO 1/2" WRENCHES (OR PLIERS)
AquaSweep
Dock Mount
with Oscillator

Assembly Instructions
1. Begin the assembly of your AquaSweep dock mount model by removing the stainless-steel bolt from the
yoke assembly. Fig. 1
2. Adjust the gray AquaSweep housing to the desired angle for water ow, and secure in place with the
stainless-steel bolt. Fig. 1
3. The next step is to fasten the stainless-steel basket to the intake side of the gray AquaSweep housing.
This is easily done by aligning the 3 basket eyelets with the 3 pre-drilled holes on the housing and fastening
with the 3 small self-tapping screws provided. Fig. 2
4. Secure the dock plate to your wooden or metal dock, utilizing the 4 large self-tapping screws. Fig. 3
5. Once the dock plate has been secured, the stainless-steel pole of the oscillator can be inserted through the
dock plate sleeve. Simply loosen the 2 thumb screws from the dock plate sleeve, insert the pole from the
top through the sleeve adjusting to the desired height, and then re-tighten the 2 thumb screws. Fig. 3
6. Now, slide the yoke assembly over the bottom of the stainless-steel pole and secure with the bolt provided.
Fig. 3
7. The AquaSweep dock mount model easily adjusts for varying water levels by loosening the 2 thumb screws
from the dock plate and raising or lowering the AquaSweep assembly. Please note, the 2 thumb screws
are coated with a special lubricating compound specically designed for stainless-steel to ensure proper
function. An extra packet of this compound has been included with your AquaSweep purchase; periodic
lubrication of the 2 thumb screws is required for years of problem free use and for warranty validation.
8. Finally, power can be supplied to your AquaSweep utilizing a standard 110 volt receptacle protected by
a GFCI. Extension cords should not be used for the Aquasweep. Run an extension cord to the Oscillator
assembly, connecting it to a plug protected by a GFCI. Disconnect power when swimmers are present.
Dock Plate
Yoke
Adjustment
Fig. 1 Fig. 3
18"
Fig. 2 Basket
Installation

Auto Function:
Press both left limit switches and at the same time and the device will begin pre-set operation.
Auto Function Operates from 90°L - 270°R.
Left and Right Limit
Adjust the AquaSweep to the desired rotation.
Use and buttons to set the left limit
and and to set the right limit
of the AquaSweep pattern. The display shows
“Lxxx” and “Rxxx” where “xxx” is limit angle in
degrees corresponding to the chart shown at right.
Speed
The and buttons will adjust the speed of the left/right movement. “SP xx” will display
where xx is the speed in degrees per minute. 1 degree per minute will take about six hours to complete a sweep
(one end to the other and back) if the left/right limits are 180 degrees apart. At 90 degrees per minute this will
take a little less than four minutes. The sweep speed can be set to zero, turning o the oscillator.
Timer
The and buttons set how long the device runs then how long it is idle in hours. For instance, it can run
for six hours then sleep for six hours. Pressing both together will toggle between “PAUSE” mode (system o
indenitely) and “RUN” mode (normal operation). Press the and buttons together to pause the system.
Display will show “PAUSE”. Press any button to exit pause mode. Setting the o time to zero will keep the
system from turning o.
ON
TIME
RATE
RATE OFF
TIME
10°
90°
20°
30°
40°
50°
60°
180° 190° 200°
210°
220°
230°
240°
250°
260°
270°
350°
60
°
°
Dock
70°
80°
100°
110°
120°
130°
140°
150°
160°
170°
280°
290°
300°
310°
320°
330°
340°
Max Left/Right
10° - 350°

13245 Barry Street, Holland, MI 49424
scottaerator.com
[e-mail]
800-WATER-45 (800-928-3745)
[phone]