Scott MDX i65 User manual

GB–1
IMPORTANT
Since CD circuitry may cause interference to other radio tuners nearby, switch this unit off when
not in use or move it away from the affected radio tuner.
NOTE:
This digital apparatus does not exceed the Class A/Class B (whichever is applicable) limits for
radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of
Industry Canada. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and if not installed and used in accordance with the instruction, may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television, which can be determined by turning the equipment off and the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio / TV technician for help.
SAFETY
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGESARE PRESENT INSIDE THE
ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL
ONLY.
Mains plug is used as the disconnected device and it shall remain readily
operable. To be completely disconnected the power input, the mains plug of the
apparatus shall be disconnected from the mains completely. The mains plug
should not be obstructed OR should be easily accessed during intended use.
“The apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.”
–no naked flame sources such as lighted candles should be placed on the apparatus;
–attention should be drawn to the environmental aspects of battery disposal;
–the use of apparatus in moderate climates.
LASER:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference. Should the unit require maintenance, contact an qualified service personnel.
Use of controls, adjustments or the performance of procedures other than those specified may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.

GB–2
SAFETY
DO NOT STARE INTO BEAM
LASER
Type Semiconductor laser GaAIAs
Wave length 650nm
Output Power 7mW
Beam divergence 60 degree

GB–3
SAFETY
CAUTION :
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN
THIS OWNER’S MANUALAND THOSE MARKED ON THE UNIT. KEEP THESE
INSTRUCTIONS. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result
in electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you
observe the following procedures for installation, use and servicing. This unit does not contain
any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS
VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions
After unpacking this product, read the owner manual carefully.
2. Keep these instructions
Retain this booklet for future reference.
3. Heed all warnings.
4. Follow all the operating and other instructions.
5. Do not use this apparatus near water.
6. Clean only with a damp cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturers
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11.Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when the power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
14. Disc Tray
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal
injury.
15. Burden
Do not place a heavy object on, or step on the product. The object may fall, causing serious
personal injury and serious damage to the product.

GB–4
SAFETY
16. Disc
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may
cause serious personal injury and product malfunction.
17. Damage Requiring Service
Unplug this product from the wall refer servicing to qualified service personnel under the
following conditions:
a.) When the power-supply cord or plug is damaged.
b.) If liquid has been spilled, or objects have fallen into the product.
c.) If the product has been exposed to rain or water.
d.) If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions. Improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician
to restore the product to its normal operation.
e.) If the product has been dropped or damaged in any way.
f.) When the product exhibits a distinct change in performance - this indicates a need for
service.
18. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
Remark :
Power Indication
1. The mains plug is used as the disconnect device and it shall remain readily
operable to be completed disconnect the power input, disconnected from
the mains.
2. Since the mains plug is used as disconnect.
Device and the stand-by indicator would light-up to indicate power on. If the
stand-by indicator turns off (no color), the apparatus is completely
disconnected from the mains.
Notes : See Marking on Bottom / Rear Cabinet
PLAYER ZONES
For the purpose of distribution of DVD Discs, the world has been separated into 6 zones. The
zone your player is intended for is indicated on the “Zone Label”. This should be the same as the
label on discs available in your region. If you have any difficulties in playing a disc, make sure that
the disc is for the same zone as your player.

GB–5
INSTALLATION
Install your DVD player on a stable flat surface. The unit should be situated with enough space
around it so that proper heat ventilation is assured. Allow 20 cm clearance from the rear and the
top of the unit, and 10 cm from each side.
Caution :
Do not install this equipment in confined space with poor ventilation.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation,and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited
.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation,and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited
.
Apparatus Claims of U.S. Patent Nos.4,631,603;
4,819,098; 4,907,093;5,315,448;and 6,516,132
licensed for limited viewing uses only.
Apparatus Claims of U.S. Patent Nos.4,631,603;
4,819,098; 4,907,093;5,315,448;and 6,516,132
licensed for limited viewing uses only.
Consumers should note that not all high definition televison sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case of 525 or 625 progressive scan picture problems,
it is recommended that the user switch the connection to the standard definition output. If there are
questions regarding our TV set compatibility with this model 525p and 625p DVD player, please contact
our customer service center.

Consumers should note that not all high definition televison sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case of 525 or 625 progressive scan picture problems,
it is recommended that the user switch the connection to the standard definition output. If there are
questions regarding our TV set compatibility with this model 525p and 625p DVD player, please contact
our customer service center.

Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.

Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.

CONNECTIONS
1) Connecting to TV
Only the component cable and the audio cable need be connected if your TV has COMPONENT
input as this will give a higher quality picture. Otherwise use the SCART or Video input of the TV.
COMPONENT CABLE CONNECTING

GB–6
CONNECTIONS
SCART CABLE CONNECTING
VIDEO CABLE CONNECTING

GB–7
CONNECTIONS
2) Connecting to the standard speaker boxes
CONNECTING TO SPEAKER BOXES
Notes:
To enjoy the SURROUND SOUND with the above connection, you need to set the
corresponding preference in setup menu. Press SETUP key on the remote control to access
menu, then press PRESET / or PRESET / , or TUN / or TUN / key to
select AUDIO OUT and the ANALOG, SPDIF/RAW or SPDIF/PCM, press / ENTER key to
confirm your setting. To exit setup menu, press SETUP key once.

GB–8
CONNECTIONS
3) Connecting to AM and FM antenna
A.) Adjusting the position of the FM antenna
While listening to an FM program, extend the antenna and move it in various directions until the
clearest signal is received. Then secure the antenna with push pins in the position with the least
distortion.
B.) Adjusting the position of the AM antenna
Connect the AM antenna wire to antenna marked “ ” with the white wire.
Connect the AM antenna wire to antenna marked “ ” with the black wire.
While listening to an AM program, set the antenna in the direction and position where you receive
the clearest sound. Position it as far away as possible from the unit, TVs, speaker cables and
power cords (main leads).

GB–9
MAIN UNIT
1. – Turns the system on or standby. Remember to remove the power of the system, if you
are not going to use the system for a period of time.
2. FM/AM – Selects TUNER as input source, switches the DVD Micro System on from standby
with TUNER selects as the input source. Switches between the FM and AM frequency bands.
3. SOURCE – Switches the DVD Micro System on from standby with DISC, USB, CARD, AUX IN
select as the input source.
Switches among the DISC, USB, CARD , AUX IN as input source.
4. – To open or close the disc tray.
5. PLAY/PAUSE – In DISC , USB or CARD mode: starts disc playback; pauses playback.
6. STOP - Ends DISC , USB or CARD playback.
7. VOLUME – – Adjusts Volume down.
8. VOLUME + – Adjusts Volume up.
9. / PRESET – – In Disc playback mode, press to skip backward to the other track/chapter; In
Tuner mode, press briefly to select a preset station down. Press and hold down to start the
station search mode backwards.
10. / PRESET + – In Disc playback mode, press to skip forward to the other track/chapter; In
Tuner mode, press briefly to select a preset station up. Press and hold down to start the
station search mode forwards.
11. IR – Infrared sensor for remote control.
12. – Headphones jack for connecting a stereo head phone set with a jack plug (no including).
The loudspeakers are switched off automatically.
13. USB – USB connector.
14. CARD – CARD connector.

GB–10
REMOTE CONTROLS
10
2
8
15
13
24
28
21
14
9
1
27
16
12
7
3
6
18
23 25
31
33
34
37
38
41
42
5
11
20
17
26
19
29
30
32
35
36
39
40
43
44
22
4
1. – Turns the system on or standby. Remember to remove the power, if you are not going to
use the system for a long time.
2.OPEN / CLOSE – To open / close the disc tray.
3. DVD – Selects Disc mode from other source modes; In Standby mode, turns the system on at
Disc mode directly.
4. TUNER – Selects Tuner AM, FM band from other source modes; In Standby mode, turns the
system on at turn AM or FM band directly.
5. AUX – Selects AUX mode from other source modes; In Standby mode, turns the system on at
AUX mode directly.
6. USB – Selects USB mode from other source modes; In Standby mode, turns the system on at
USB mode directly.
7. CARD – Selects CARD mode from other source modes; In Standby mode, turns the system on
at CARD mode directly.
8. DIGITS (0~9) – Numerical buttons for various inputs. In DISC, USB, CARD mode, selects
tracks or files directly. In TUNER mode, selects preset station position directly.
9. +10 – If the number of track of files is over 10, press >>+10 << to set ten digit, then
press numerical key to select primacy number.

GB–11
REMOTE CONTROLS
10. PROG – In Disc, USB, CARD mode, enters or exits the function for track memory (PROGRAM).
In tuner mode, opens the function for storing radio stations in preset channel positions
confirms your setting.
11. OSD/INFO – Press briefly to view the current state for title No, chapter No, elapsing time (on
top TV screen). Press twice to exit the state menu (if CD disc) or view angle/subtitle state are
on or off (if DVD disc). Press thrice to exit the state menu (if DVD disc). Press and hold down
more than two seconds to enter DIMMER mode for VFD display. In FM mode, press the key to
display RDS information.
12. CLOCK – Press the CLOCK key to display current time briefly, press and hold down more
than 2 seconds to enter the clock setting.
13. TIMER – Press the TIMER key to switch the timer ON or OFF, press and hold down to enter
the timer setting mode.
14. SLEEP – Press the SLEEP key to view sleep time if the sleep time is set; press and hold down
more than 2 seconds to enter the sleep time setting mode.
15. SETUP – Calls up the set-up menu of the DVD Micro System on the television screen when
the system is switched to DISC, USB or CARD mode.
16. TUN / – Moves the cursor left in the set-up menu (on the TV screen). In DISC, USB,
CARD playback mode, press and hold down to starts reverse in search; In TUNER mode,
switches the frequency down; In CLOCK setting mode, selects the hour or minute for
adjustment.
17. TUN / – Moves the cursor right in the set-up menu (on the TV screen). In DISC, USB,
CARD playback mode, press and hold down to starts fast forward in search; In TUNER mode,
switches the frequency up; In CLOCK setting mode, selects the hour or minute for adjustment.
18. PRESET / – Moves the cursor up in the set-up menu or MP3, MPEG 4 filelist (on the TV
screen). In TUNER mode, switches forward through the preset stations step by step. In
CLOCK or TIMER setting mode, adjusts the values such as hour, minute, volume source.
19. PRESET / – Moves the cursor up in the set-up menu or MP3, MPEG 4 filelist (on the TV
screen). In TUNER mode, switches backward through the preset stations step by step. In
CLOCK or TIMER setting mode, adjusts the values such as hour, minute, volume source.
20. / ENTER – Activates the selected setting and confirms the entry in the set-up menu. In DISC,
USB or CARD mode, starts disc playback, pause playback.
21. – During playback, press once briefly interrupt playback (resume). Press twice to end
playback (stop).
22. VOLUME / – Adjust the volume up and down.
23. TITLE – Calls up the DVD setting according to the track of a DVD.
24. SUBTITLE – For selecting and displaying subtitles of the DVD during playback according to
the DVD prerequisites. Select to change subtitles during DivX playback.
25. MENU – Calls up the DVD settings according to the menu of the DVD.
26. AUDIO – Press briefly to choose the audio language you prefer according to the DVD
prerequisites.
27. STEP – Switches to freeze frame forwards during DVD/ MPEG 4 and VCD/S-VCD playback,
switches through freeze frames step by step.
28. SLOW – Press each time briefly to switch to play in slow motion among 1/2,1/3,1/4,1/5, 1/6,
1/7.
29. NEXT / – In DISC, USB or CARD mode, press to skip forward the other track /chapter
30. PREV / – In DISC, USB or CARD mode, press to skip forward the other track /chapter.

GB–12
REMOTE CONTROLS
31. GOTO – In DVD mode, press to select the desired title or chapter; In CD, VCD disc mode,
press to the desired starting point for playback (If VCD disc, PBC must be set as off).
32. REPEAT – In CD, MP3, WMA, SVCD and VCD disc mode, repeatedly selects the disc repeat
modes: REPEAT (repeat the current track), REPEAT ALB (album repeat) for MP3 and WMA
disc; REPEAT ALL (repeat all tracks of disc) ; Repeat off (remark: For VCD20 or SVCD, it is
available when PBC is set as off mode); In DVD disc mode, repeatedly selects the playback
mode, RPT CHP (repeat current chapter), RPT TITLE (repeat current title).
33. BOOKMARK/PBC - Switches the PBC (Play Back Control) function on and off in VCD/S-VCD
mode. Calls up the menu for setting bookmark in DVD mode.
34. INTRO – In CD/VCD/SVCD disc, press briefly to select chapter /track for playback in intro
order.
35. RDS/A-B – In DISC , USB or CARD mode, marks a section, which is then constantly
repeated.In FM mode, press the key to select the type of program that they broadcast.
36. RAND – In DISC, USB or CARD mode, playback track/chapter in random order.
37. P-SCAN – In DISC, USB or CARD mode, switches the output format of the picture of signal
amongINTERLACE-YUV,TV-RGB, P-SCANYPBPR.
38. ST/MONO – In VCD/SVCD disc, selects channel of audio output; Switches between STEREO
andMONO.
39. ANGLE – Selects the DVD setting appropriately during playback of various camera angles for
certain scenes of passages on the DVD.
40. ZOOM – You press ZOOM button to enlarge or zoom out the video image during play DVD/
VCD and JPEG Picture disc.
41. MUTE – Press MUTE button to reduce sound to an inaudible level, and “ MUTING ” will be
displayed on screen. Press the button again to resume, and “ MUTING ” has gone off.
42. DEMO – Press briefly to activate the DEMO function ON and OFF in standby mode.
43. BASS – Press briefly to switch the BBS (Bass Boost) function among BASS 1, BASS 2 or
BASS OFF.
44. EQ – Selects a different sound effect among FLAT, CLASSIC, ROCK, JAZZ and POP.

GB–13
BASIC SETUP
1. General Steps of Setup Menu
a.) In DISC, USB or CARD mode, press the SETUP key on the remote control , the main setup
menu appears as below. When the main menu displayed, the DVD system will auto pause.
RATING
DEFAULT
EXIT SETUP
SYSTEM SETUP
SCREEN SAVER
SCREEN SAVER
VIDEO
TV TYPE
PASSWORD
PASSWORD
TV SYSTEM
TV SYSTEM
b.) Press TUN / and TUN / key to highlight the icon of the desired page, then press
PRESET / or TUN / key to activate that page; For example, if you want to setup the
audio page, press TUN / key to highlight the audio icon, the audio page will be displayed
on the screen.
AUDIO SETUP
EXIT SETUP
OP MODE
DYNAMIC RANGE
DYNAMIC RANGE
LINE OUT
LINE OUT
RF REMOD
RF REMOD
DUAL MONO
c.) Press PRESET / key to highlight the desired option. Press / ENTER or TUN /
key to select, the choices of that option appear on the right; For example, press PRESET /
key to highlight the BRIGHTNESS option, then press / ENTER key to select, the
brightness choices appear on the right.
VIDEO SETUP
EXIT SETUP
BRIGHTNESS
CONTRAST
HUE
SATURATION
SHARPNESS
12
10
8
6
4
2
0
ANGLE SWITCH
ANGLE SWITCH
d.) Press PRESET / key to highlight the Exit Setup option, then press / ENTER key or
SETUP key again to exit Setup Menu.

GB–14
BASIC SETUP
2. Setup Items Introduction
SYSTEMSETUP
• TV SYSTEM
According to the Color System of the TV, you can choose the TV System.
–NTSC : Choose this settings if your DVD player is connected to a NTSC TV.
–PAL : Choose this settings if your DVD player is connected to a PAL TV.
–PAL-M : Choose this settings if your DVD player is connected to a PAL M TV.
–AUTO : Choose this settings if your DVD player is connected to a multi-system TV.
SYSTEM SETUP
SCREEN SAVER
SCREEN SAVER
VIDEO
TV TYPE
PASSWORD
RATING
DEFAULT
EXIT SETUP
TV SYSTEM NTSC
PAL
PAL M
AUTO
• SCREEN SAVER
If the screen saver is on, when your DVD player is in Stop, Open, or No Disc state, or there is a
frame frozen for more than 3 minutes, the screen saver will be displayed. This feature can
protect the screen from damage.
–ON : Choose this setting to activate the screen saver.
–OFF : Choose this setting to cancel the screen saver
SYSTEM SETUP
VIDEO
TV TYPE
PASSWORD
RATING
DEFAULT
EXIT SETUP
ON
OFF
SCREEN SAVER
TV SYSTEM
TV SYSTEM
• VIDEO
–INTERLACE-YUV : Choose this setting if your DVD player is connected to a TV with Y, Cb, Cr
video cables.
–TV-RGB : Choose this setting if your DVD player is connected to a TV with an SCART cable.
–P-SCAN : Choose this setting if your DVD player is connected to a progressive scan TV with Y,
Pb, Pr video cables.

GB–15
BASIC SETUP
SYSTEM SETUP
TV TYPE
PASSWORD
RATING
DEFAULT
EXIT SETUP
INTERLACE-YUV
TV-RGB
TV SYSTEM
TV SYSTEM
VIDEO
P-SCAN YPBPR
SCREEN SAVER
SCREEN SAVER
Notes :
–If composite Video is connected to your TV, the submenu INTERLACE-YUV must be selected.
–If the component cable (Y, Pb/Cb, Pr/Cr) is connected to your TV for interlace TV or progressive
scan TV, the submenu P- SCAN YPBPR must be selected.
Remark : The mechanism switch need to move to the YUV position on the back
panel.
–If the scart cable is connected to your TV, the submenu TV-RGB must be selected.
Remark : The mechanism switch need to move to the RGB position on the back
panel.
• TV TYPE
–16 : 9 (Wide Screen): Choose this setting if your DVD player is connected to a wide screen TV.
If you choose this setting and you don’t have a wide screen TV, the images on the screen may
appear distorted due to vertical compression.
–4 : 3 LB (Letter Box): Choosing this setting if your DVD player is connected to a normal ratio TV.
You’ll see the movies in their original aspect ratio (height-to-width ratio). You’ll see the entire
frame of the movie, but it will take up a smaller portion of the screen vertically. The movie might
appear with black bars at the top and bottom of the screen.
–4 : 3 PS (Pan & Scan): Choosing this setting if your DVD player is connected to a normal ratio
TV. You can fill the movie to the entire screen of your TV. This might mean that parts of the
picture (the left and right edges) won’t be seen.
SYSTEM SETUP
PASSWORD
RATING
DEFAULT
EXIT SETUP
4:3PS
4:3LB
SCREEN SAVER
TV SYSTEM
TV SYSTEM
TV TYPE
16:9
VIDEO
Notes :
The image display ratio is related to the recorded disc format. Some disc can not display
images in the aspect ratio you choose.
If you play a disc recorded in 4:3 format on a wide screen TV, black bars will appear on the
left and right side of the screen.
You must adjust the screen setting depending on the type of the television you have.

GB–16
BASIC SETUP
• PASSWORD
The password option is initialized locked, and you cannot set the ratings limit or change the
password. In order for the Ratings feature work, the password mode must be turned on. If you
want to set the ratings limit, you will need to enter the default password, which is 00000, then
press / ENTER key to confirm. To change the password, you will be prompted for the old
password, then be prompted for a new. Enter a 5-digit number (this is your password).
SYSTEM SETUP
RATING
DEFAULT
EXIT SETUP
SCREEN SAVER
TV SYSTEM
TV SYSTEM
PASSWORD
VIDEO
TV TYPE
• RATING
Press PRESET / or PRESET / key to RATING option , you can setup the parental rating
when password is unlock. The following settings are available 1 to 8.
SYSTEM SETUP
DEFAULT
EXIT SETUP
SCREEN SAVER
TV SYSTEM
TV SYSTEM
RATING
VIDEO
TV TYPE
PASSWORD
1G
1 G
2
3PG
4 PG13
5
6R
7 NC-17
8
Notes:
–1 G : Suitable for all ages.
–2 : Level 2.
–3 PG : Only with parental guidance.
–4 PG13 : Not suitable for children under 13 age, from 13 to 18 only under parental guidance.
–5 : Level 5
–6 R : May contain violence or sex scene, can only be viewed under 18 under with parental
guidance.
–7 NC-17 : Only for adults, not for those under 17.
–8 : Only for adults.
If the password option is locked, your can’t set the rating limit, the rating limit doesn’t work when
the password option unlocked.

GB–17
BASIC SETUP
• DEFAULT
Choose this option to resume all the setup options to default settings.
SYSTEM SETUP
EXIT SETUP
SCREEN SAVER
TV SYSTEM
TV SYSTEM
DEFAULT
VIDEO
TV TYPE
PASSWORD
RESTORE
RATING
LANGUAGESETUP
• OSD LANGUAGE
Highlight the OSD LANGUAGE option, and press PRESET / or PRESET / key to choose
the OSD language you prefer. Press / ENTER key to confirm, and it will display OSD in that
language; There are 7 optional OSD languages: English, German, Spanish, French and Portu-
guese, Italian or Swedish.
LANGUAGE SETUP
AUDIO LANG
AUDIO LANG
SUBTITLE LANG
SUBTITLE LANG
MENU LANG
MENU LANG
EXIT SETUP
OSD LANGUAGE ENGLISH
GERMAN
SPANISH
FRENCH
PORTUGUESE
ITALIAN
SWEDISH
• AUDIO LANG
Highlight the AUDIO LANG option, and press PRESET / or PRESET / key to choose the
audio language you prefer. Press / ENTER key to confirm. If the disc you are playing has that
language available, it will output audio in that language; There are 8 optional audio languages:
Chinese, English, Japan, French, Spanish, Portuguese, Latin and German.
LANGUAGE SETUP
AUDIO LANG JAPAN
FRENCH
SPANISH
PORTUGUESE
OSD LANGUAGE
OSD LANGUAGE
LATIN
SUBTITLE LANG
SUBTITLE LANG
MENU LANG
MENU LANG
EXIT SETUP
ENGLISH
CHINESE
GERMAN

GB–18
BASIC SETUP
• SUBTITLE LANG
Highlight the SUBTITLE LANG option, and press PRESET / or PRESET / key to choose
the subtitle language you prefer. Press / ENTER key to confirm. If the disc you are playing has
that language available, it will displays subtitles in that language; There are 7 optional audio
languages: Chinese, English, Japan, French, Spanish, Portuguese and German.
LANGUAGE SETUP
MENU LANG
MENU LANG
EXIT SETUP
EXIT SETUP
SUBTITLE LANG
CHINESE
ENGLISH
JAPAN
FRENCH
SPANISH
PORTUGUESE
OSD LANGUAGE
OSD LANGUAGE
GERMAN
OFF
AUDIO LANG
AUDIO LANG
• MENU LANG
Highlight the MENU LANG option, and press PRESET / or PRESET / key to choose the
menu language you prefer. Press / ENTER key to confirm. If the disc you are playing has that
language available, it will displays menu in that language; There are 8 optional menu languages :
Chinese, English, Japan, French, Spanish, Portuguese ,German or Latin.
LANGUAGE SETUP
EXIT SETUP
EXIT SETUP
MENU LANG
CHINESE
ENGLISH
JAPAN
FRENCH
SPANISH
PORTUGUESE
OSD LANGUAGE
OSD LANGUAGE
GERMAN
LATIN
AUDIO LANG
AUDIO LANG
SUBTITLE LANG
SUBTITLE LANG
DIGITALSETUP
• AUDIO OUT
Highlight the AUDIO OUT option, and press PRESET / or PRESET / key to choose the
audio output mode you prefer. Press / ENTER key to confirm; There are 3 optional audio output
modes:SPDI/ OFF, SPDIF/RAW, andSPDIF/ PCM.
–SPDIF / OFF : From the Coaxial Output jack and the Optical Output jack, no signal is output.
–SPDIF / RAW : Choose this setting if your DVD player is connected to a power amplifier with a
coaxial cable or an optical cable; When playing a disc recorded with Dolby Digital, DTS and
MPEG audio formats, the corresponding digital signals will be output from the Coaxial Output
jack or Optical Output jack. This player’s digital output jacks are designed for a connection to a
Dolby Digital, DTS, or MPEG receiver or decoder.

GB–19
BASIC SETUP
–SPDIF / PCM: Choose this setting if your DVD player is connected to a 2-channel digital stereo
amplifier; When playing a disc recorded with Dolby Digital and MPEG audio formats, audio signals
will be modulated into a 2-channel PCM signal, and it will be output from the Coaxial Output jack
or Optical Output jack.
DIGITAL SETUP
EXIT SETUP
AUDIO OUT
KEY
SPDIF/OFF
SPDIF/RAW
SPDIF/PCM
• KEY
Press PRESET / or PRESET / key to move the scroll and adjust the key.
DIGITAL SETUP
EXIT SETUP
KEY
AUDIO OUT
AUDIO OUT
#
+4
+2
0
-2
-4
b
VIDEOSETUP
• BRIGHTNESS
Press PRESET / or PRESET / key to move the scroll and adjust the brightness.
VIDEO SETUP
EXIT SETUP
BRIGHTNESS
CONTRAST
HUE
SATURATION
SHARPNESS
12
10
8
6
4
2
0
ANGLE SWITCH
ANGLE SWITCH
• CONTRAST
Press PRESET / or PRESET / key to move the scroll and adjust the contrast.
VIDEO SETUP
EXIT SETUP
SATURATION
SHARPNESS
12
10
8
6
4
2
0
BRIGHTNESS
CONTRAST
HUE
ANGLE SWITCH
ANGLE SWITCH