Scout Wifi onboard User manual

www.scoutantenne.com Page 1/8

To avoid burning and voltage caused traumas, of the personnel working with the device, please follow these safety requirements:

The device is intended for supply from a Limited Power Source (LPS) that power consumption should not exceed

15VA and current rating of over current protective device should not exceed 2A.

The highest transient over voltage in the output (secondary circuit) of used PSU shall not exceed 36V peak.

The device can be used with the Personal Computer (rst safety class) or Notebook (second safety class). Associated

equipment: PSU (power supply unit) (LPS) and personal computer (PC) shall comply with the requirements of

standard EN 60950-1.

Do not mount or service the device during a thunderstorm.

To avoid mechanical damages to the device it is recommended to transport it packed in a damage-proof pack.

To avoid mechanical damage to the device it is recommended to transport it packed in a damageproof pack. When using the

device it should be placed so that its indicating LEDs would be visible as they inform in which working mode the device is in and if

it has any working problems.

Protection against over current, short circuiting and earth faults should be provided as a part of the building installation.

Signal level of the device depends on the environment in which it is working in. In case the device starts working insuciently, please

refer to qualied personnel in order to repair this product. We recommend forwarding it to a repair center or the manufacturer.

There are no exchangeable parts inside the device.

Protection in primary circuits of associated PC and PSU (LPS) against short circuits and earth faults of associated PC

shall be provided as part of the building installation.

Wi onBoard - 4G/LTE dual sim Router + 10 dB WiFi antenna

Code: PF AN NWIFI12

4G onBoard - 4G/LTE dual sim Router + 4 dB 4G/LTE antenna

Code: PF AN NWIFI13

4G onBoard Plus - 4G/LTE dual sim Router + 2x 4 dB 4G/LTE antenna

Code: PF AN NWIFI11

WiFi + 4G onBoard - 4G/LTE dual sim Router + 10 dB WiFi antenna + 4 dB 4G/LTE antenna

Code: PF AN NWIFI08

WiFi + 4G onBoard Plus - 4G/LTE dual sim Router + 10 dB WiFi antenna + 2x 4 dB 4G/LTE antenna

Code: PF AN NWIFI14

Quick start guide

(v2.19)

Thank you for purchasing a Scout product. This guide refers to all the WiFi/4G systems listed above, before installing the router

and the antenna(s) please read carefully all instructions. Customer comments are welcome.

FRONT VIEW

BACK VIEW

Mobile AUX antenna connector Mobile MAIN antenna connector

Reset button

WiFi antenna

connectors

LAN LEDs

WAN Ethernet portLAN Ethernet ports

Mobile

signal strength

indication LEDs

Power socket

Power LED Mobile connection status LED

WAN LED

1. Push the SIM holder button with the SIM needle.

2. Pull out the SIM holder.

3. Insert your SIM card into the SIM holder.

4. Slide the SIM holder back into the router.

5. Attach mobile and WiFi antennas.

6. Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter

into a power outlet.

7. Connect to the device wirelessly (SSID: RUT950_**** (unique to each device)) or use an Ethernet cable (connected

to LAN port).

HARDWARE INSTALLATION

POWER SOCKET PINOUT

1. Push the SIM holder button with the SIM needle.

2. Pull out the SIM holder.

3. Insert your SIM card into the SIM holder.

4. Slide the SIM holder back into the router.

5. Attach mobile and WiFi antennas.

6. Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter

into a power outlet.

7. Connect to the device wirelessly (SSID: RUT950_**** (unique to each device)) or use an Ethernet cable (connected

to LAN port).

HARDWARE INSTALLATION

POWER SOCKET PINOUT

WiFi + 4G onBoard - Quick start guide

www.scoutantenne.com Page 2/8

1. Push the SIM holder button with the SIM needle.

2. Pull out the SIM holder.

3. Insert you SIM card into the SIM holder.

4. Slide the SIM holder back into the router.

5. Connect 4G/LTE and WiFi antennas (see next page for the detailed description).

6. Connect the power adapter to the socket on the front device. Then plug the other

end of the power adapter into a power outlet.

7. Connect the device wirelessly (SSID: RUT950_****(unique to each device)) or use an

Ethernet cable (connected to LAN port).

Hardware installation

Power socket pinout

FRONT VIEW

BACK VIEW

Mobile AUX antenna connector Mobile MAIN antenna connector

Reset button

WiFi antenna

connectors

LAN LEDs

WAN Ethernet portLAN Ethernet ports

Mobile

signal strength

indication LEDs

Power socket

Power LED Mobile connection status LED

WAN LED

Router front view

Router back view

Antennas connection

www.scoutantenne.com Page 3/8

WiFi onBoard - connect the two internal 4G/LTE rubber antennas marked “Mobile” to the Mobile antenna connectors;

- connect the external WiFi antenna to one of the two WiFi antenna connectors;

- connect one internal WiFi rubber antenna to the other WiFi antenna connector.

Internal 4G/LTE

rubber antenna

Internal 4G/LTE

rubber antenna

Internal WiFi

rubber antenna

External WiFi

antenna

4G onBoard - connect one internal 4G/LTE rubber antenna marked “Mobile” to the Mobile AUX antenna connector;

- connect the external 4G/LTE antenna to the Mobile MAIN antenna connector;

- connect the two internal WiFi rubber antennas to the WiFi antenna connectors.

Internal 4G/LTE

rubber antenna

External 4G/LTE

antenna

Internal WiFi

rubber antenna

Internal WiFi

rubber antenna

(inversion allowed)

4G onBoard - connect the two external 4G/LTE antennas to the Mobile antenna connectors;

- connect the two internal WiFi rubber antennas to the WiFi antenna connectors.

External 4G/LTE

antenna

External 4G/LTE

antenna

Internal WiFi

rubber antenna

Internal WiFi

rubber antenna

Plus

WiFi + 4G onBoard - Quick start guide

www.scoutantenne.com Page 4/8

WiFi + 4G onBoard - connect one internal 4G/LTE rubber antenna marked “Mobile” to the Mobile AUX antenna connector;

- connect the external 4G/LTE antenna to the Mobile MAIN antenna connector;

- connect the external WiFi antenna to one of the two WiFi antenna connectors;

- connect one internal WiFi rubber antenna to the other WiFi antenna connector.

Internal 4G/LTE

rubber antenna

External 4G/LTE

antenna

Internal WiFi

rubber antenna

External WiFi

antenna

(inversion allowed)

WiFi + 4G onBoard - connect the two external 4G/LTE antennas to the Mobile antenna connectors;

- connect the external WiFi antenna to one of the two WiFi antenna connectors;

- connect one internal WiFi rubber antenna to the other WiFi antenna connector.

External 4G/LTE

antenna

External 4G/LTE

antenna

Internal WiFi

rubber antenna

External WiFi

antenna

(inversion allowed)

Plus

Antennas reference

External 4G/LTE

antenna

External WiFi

antenna

Internal WiFi

rubber antenna

Internal 4G/LTE

rubber antenna

WiFi + 4G onBoard - Quick start guide

TECHNICAL INFORMATION

1. To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL ﬁeld of your Internet browser.

2. Use login information shown in image A when prompted for authentication.

3. After you login, you will be prompted to change your password for security reasons. The new password must

contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is

mandatory and you will not be able to interact with the router's WebUI before you change the password.

4. When you change the router's password, the Conﬁguration Wizard will start. The Conﬁguration Wizard is a tool

used to setup some of the router's main operating parameters.

5. Go to the Status > Network page and pay attention to the Signal Strength indication (image B). To maximize

the cellular performance try adjusting the antennas or changing the location of your device to achieve the best

signal conditions.

*Order code dependent.

**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

Radio speciﬁcations

Bundled antennas speciﬁcations*

RF technologies

Max RF power

GSM, GPRS, EDGE, UMTS/HSPA+, LTE, GNSS, WiFi

33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi

GSM/WCDMA/LTE antenna 698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain** 3 dBi, omnidirectional, SMA male connector

WiFi antenna 2400~2483.5 MHz, 50 Ω, VSWR<2, gain** 5 dBi, omnidirectional, RP-SMA male connector

Mobile Information

Mobile

Data connection state

IMEI

IMSI

Sim card state

Signal strength

Connected

123456789012345

Ready

-79 dBm

http://192.168.1.1

Please enter username and password

Username

Password

admin

admin01

1. Scan for available networks with your wireless device (Smartphone, Tablet, Laptop), choose the wireless network RUT950_****

from the list and click Connect. Enter the WiFi password located on the device’s bottom label.

2. To enter the router’s Web interface (WebUI), type http://192.168.1.1 into the URL eld of your Internet browser.

3. Use login information shown in image A when prompted for authentication.

4. After you login, you will be prompted to change your password for security reasons. The new password must contain at least 8

characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory and you will not be

able to interact with the router’s WebUI before you change the password.

5. When you change the router’s password, the Conguration Wizard will start. The Conguration Wizard is a tool used to setup

some of the router’s main operating parameters.

6. Go to the Status > Network page and pay attention to the Signal Strength indication (image B). To maximize the cellular

performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

WAN setting

To set the WAN select Network > WAN from the main Menu.

The Operation Modes window lets you determine how the router will be connecting to the internet. You can chose between three

types of WAN – Mobile, Wired and Wi-Fi. You can also setup backup WAN options in case your main connection goes down.

You can choose one main WAN and one or two (or none) backup WAN options. To choose your main WAN just check the desired

option (wired, mobile or Wi-Fi) in the Main WAN column (rst from the left), to choose a backup WAN(s), check the desired option(s)

in the Backup WAN column (second from the left). Above is an example of a conguration that uses wired as Main WAN and

mobile as Backup WAN. The Operation Modes tab also displays each interfaces name, WAN IP address and Protocol in use.

To congure a WAN interface more in depth, click the Edit button located to the right of the desired interface. Each interface

congures separately, to avoid redundancy this chapter will only overview the conguration of the wired WAN interface, since

mobile contains less information and Wi-Fi is basically the same.

www.scoutantenne.com Page 5/8

Table of typical WAN congurations depending on the system setup

System Main WAN Backup WAN

WiFi onBoard WiFi (WAN3) -

4G onBoard Mobile (WAN2) -

4G onBoard Plus Mobile (WAN2) -

WiFi + 4G onBoard WiFi (WAN3) Mobile (WAN2)

WiFi + 4G onBoard Plus WiFi (WAN3) Mobile (WAN2)

WiFi + 4G onBoard - Quick start guide

www.scoutantenne.com Page 6/8

Scan for available networks

When the main WAN or the backup WAN is set on WiFi (WAN3) you can scan the surrounding area and attempt to connect to a

new wireless access point.

1. Enter the router’s Web interface (WebUI).

2. Go to the Network > WAN page and click the Scan button to scan the surrounding area as shown in picture below.

3. You will be redirected to the window shown below.

4. Pressing Start scan will initiate a scan for available WiFi Access Points in the area. After the scan nishes, you will see a list of

these Access points. Choose one according to your liking and press the Join Network button next to it.

5. Type in the password to access the selected network and press Save.

5. You’re now connected to the external wireless access point, the free Internet signal is available on board.

WiFi + 4G onBoard - Quick start guide

APP for Android and iOS

Teltonika Router is an application developed for Android and for iOS to easily setup, monitor and manage the

router (model Sea-Hub plus).

You can dawnload the app for free on Goggle Play and App Store.

Complete user manual

All the information ragarding the router (model Sea-Hub plus) are hosted by a Wiki page which contains user manuals, conguration

guides, certication information and much more.

Please nd it at the following internet address: https://wiki.teltonika.lt/view/RUT950

www.scoutantenne.com Page 7/8

Remote Management Solution (RMS)

The Remote Management System (RMS) is a Cloud-based IoT platform designed for intuitive and convenient remote monitoring,

conguration and control of the router (model Sea-Hub plus). In case you need assistance with your router conguration you can

allow Scout to manage and monitor your router at distance (the router must be connected to the Internet). To active the RMS

function please follow these steps:

1. Enter the router’s Web interface (WebUI).

2. Go to the System > Administration > RMS page and ag the “Enable remote monitoring” option, than click the Save button.

3. Ask Scout helpdesk (e-mail: [email protected]) to connect to your router. You must provide the router serial number

and router LAN MAC address. All the information are displayed in the same page (System > Administration > RMS).

WiFi + 4G onBoard - Quick start guide

RUT950 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the

communication module in prescribed applications and environments.

SAFETY INFORMATION

[EN] English Hereby, TELTONIKA declares that this RUT950 is in compliance with the essential requirements and other relevant provisions of

Directive CE/RED.

[BG] Bulgarian С настоящето, TELTONIKA декларира, че RUT950 е в съответствие със съществените изисквания и другитеприложими разпоредби на

Директива CE/RED.

[CZ] Czech TELTONIKA tímto prohlašuje, že RUT950 splňuje základní požadavky a všechna příslušná ustanoveni Směrnice CE/RED.

[DE] German Hiermit erklärt TELTONIKA dass sich das Gerät RUT950 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen

einschlägigen Bestimmungen der Richtlinie CE/RED beﬁndet.

[DK] Danish Undertegnede TELTONIKA erklærer herved, at følgende udstyr RUT950 overholder de væsentlige krav og øvrige relevante krav i direktiv CE/RED.

[EE] Estonian Käesolevaga kinnitab TELTONIKA seadme RUT950 vastavust direktiivi CE/RED põhinõuetele ja nimetatud direktiivist tulenevatele teistele

asjakohastele sätetele.

[ES] Spanish Por la presente, TELTONIKA declara que este RUT950 cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva CE/RED.

[FI] Finish TELTONIKA vakuuttaa täten että RUT950 tyyppinen laite on direktiivin CE/RED oleellisten vaatimusten ja sitä koskevien direktiivin muiden

ehtojen mukainen.

[FR] French TELTONIKA déclare que cette RUT950 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive CE /RED.

[GR] Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ TELTONIKA ΔΗΛΩΝΕΙ ΟΤΙ RUT950 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ

ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ CE/RED.

[HU] Hungarian A TELTONIKA ezzennel kijelenti, hogy a RUT950 típusú berendezés teljesíti az alapvető követelményeket és más CE/RED irányelvben

meghatározott vonatkozó rendelkezéseket.

[IT] Italian Con la presente TELTONIKA dichiara che questo RUT950 è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla

direttiva CE/RED.

[LT] Lithuanian Šiuo dokumentu UAB TELTONIKA deklaruoja, kad šis RUT950 atitinka esminius reikalavimus ir kitas CE/RED Direktyvos nuostatas.

[LV] Latvian Ar šo TELTONIKA deklarē, ka RUT950 atbilst Direktīvas CE/RED būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

[NL] Dutch Hierbij verklaart TELTONIKA dat het toestel l RUT950 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van

richtlijn CE/RED.

[NO] Norwegian TELTONIKA Erklærer herved at RUT950 er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv CE/RED.

[PL] Polish Niniejszym TELTONIKA deklaruje że RUT950 jest zgodny z zasadniczymi wymaganiami i innymi właściwymi postanowieniami Dyrektywy CE/RED.

[PT] Portuguese Eu, TELTONIKA declaro que o RUT950 cumpre os requisitos essenciais e outras provisões relevantes da Directiva CE/RED.

[RO] Romanian Prin prezenta, TELTONIKA declară că aparatul RUT950 este în conformitate cu cerinţele esenţiale şi cu alte prevederi pertinente ale Directivei

CE/RED.

[SE] Swedish Härmed intygar TELTONIKA att denna RUT950 är i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser

som framgår av direktiv CE/RED.

[SI] Slovenian TELTONIKA izjavlja, da je ta RUT950 v skladu z bistvenimi zahtevami in drugimi relevantnimi določili direktive CE/RED.