Sea Tel 9711-92 User manual

Sea Tel, Inc.
4030 Nelson Avenue
Concord, CA 94520
Tel: [phone]
Fax: [phone]
Web: http://www.cobham.com/seatel
Sea Tel Europe
Unit 1, Orion Industrial Centre
Wide Lane, Swaythling
Southampton, UK S0 18 2HJ
Tel: [phone]
Fax: [phone]
Web: http://www.cobham.com/seatel
Sea Tel Inc is also doing business as Cobham SATCOM - Maritime
April 8, 2014 Document. No. 139192 Revision A2
INSTALLATION AND OPERATION MANUAL
FOR SEA TEL MODEL
9711-92 KU-BAND TX/RX ANTENNA
WARNING: RF RADIATION HAZARD
This stabilized antenna system is designed to be used with transmit/receive equipment
manufactured by others. Refer to the documentation supplied by the manufacturer which
will describe potential hazards, including exposure to RF radiation, associated with the
improper use of the transmit/receive equipment. Note that the transmit/receive
equipment will operate independently of the stabilized antenna system. Prior to work on
the stabilized antenna system, the power to the transmit/receive system must be locked
out and tagged.
When the transmit/receive system is in operation, no one should be allowed anywhere
within the radiated beam being emitted from the reflector.
The ultimate responsibility for safety rests with the facility operator and the
individuals who work on the system.

ii
These commodities, technology or software were exported from the United
States in accordance with the Export Administration Regulations. Diversion
contrary to U.S. law is prohibited.
Sea Tel Marine Stabilized Antenna systems are manufactured in the United
States of America.
Sea Tel is an ISO 9001:2008 registered company.
Certificate Number 13690 issued March 14, 2011.
R&TTE
CE
This Sea Tel Marine Stabilized Antenna Pedestal with DAC-2202 or DAC-2302 Antenna
Control Unit complies with the requirements of directive 1999/5/EC of the European
Parliament and of the Council of 9 March 1999 on Radio equipment and Telecommunication
Terminal Equipment. A copy of the R&TTE Declaration of Conformity for this equipment is
contained in this manual.
This Sea Tel Ku Band antenna will meet the spectral density, stabilization accuracy and, when properly
connected to the modem, the automatic cessation of transmission requirements of the 2009 version of FCC 47
C.F.R. § 25.222. Please refer to the declaration included in this manual.
Copyright Notice
Copyright © 2013 Sea Tel Inc All Rights Reserved. The information contained in this document is proprietary to Sea Tel,
Inc.. This document may not be reproduced or distributed in any form without prior written consent of Sea Tel, Inc. The
information in this document is subject to change without notice. Sea Tel Inc, is also doing business as Cobham Antenna
Systems.
This document has been registered with the U.S. Copyright Office.
Revision History
REV
ECO#
Date
Description
By
A
N/A
June 3, 2013
Production release.
MDN
A1
N/A
December 18, 2013
Update installation text and installation arrangement drawing.
MDN
A2
N/A
April 8, 2014
Corrected para 13.1 text
MDN

Document Number 130445 Revision J
24-Jan-2013
Sea Tel Inc.
4030 Nelson Ave., Concord
California, 94520, USA
T: [phone]
F: [phone]
FCC Declaration of Conformity
1. Sea Tel, Inc. designs, develops, manufactures and services marine stabilized antenna systems for
satellite communication at sea. These products are in turn used by our customers as part of their Ku-
band Earth Station on Vessels (ESV) networks.
2. FCC regulation 47 C.F.R. § 25.222 defines the provisions for blanket licensing of ESV antennas
operating in the Ku Band. This declaration covers the requirements for meeting § 25.222 (a)(1) by
the demonstrations outlined in paragraphs (b)(1)(i) and (b)(1)(iii). The requirements for meeting §
25.222 (a)(3)-(a)(7) are left to the applicant. The paragraph numbers in this declaration refer to the
2009 version of FCC 47 C.F.R. § 25.222.
3. Sea Tel hereby declares that the antennas listed below will meet the off-axis EIRP spectral density
requirements of § 25.222 (a)(1)(i) with an N value of 1, when the following Input Power spectral
density limitations are met:
*0.6 Meter Ku Band, Models 2406 and USAT-24 are limited to -21.6 dBW/4kHz
*0.75 Meter Ku Band, Models 3011 and USAT-30 are limited to -21.6 dBW/4kHz
0.9 Meter Ku Band, Model 3612 is limited to -20.3 dBW/4kHz
1.0 Meter Ku Band, Models 4003/4006/4009/4010 are limited to -16.3 dBW/4kHz
1.0 Meter Ku Band Model 4012 is limited to -16.6 dBW/4kHz
1.2 Meter Ku Band, Models 4996/5009/5010/5012 are limited to -14.0 dBW/4kHz
1.5 Meter Ku Band, Models 6006/6009/6012 are limited to -14.0 dBW/4kHz
2.4 Meter Ku Band, Models 9797 and 9711QOR are limited to -14.0 dBW/4kHz
4. Sea Tel hereby declares that the antennas referenced in paragraph 3 above, will maintain a
stabilization pointing accuracy of better than 0.2 degrees under specified ship motion conditions,
thus meeting the requirements of § 25.222 (a)(1)(ii)(A). Those antennas marked with * will
maintain a stabilization pointing accuracy of better than 0.3 degrees. The Input Power spectral
density limits for these antenna have been adjusted to meet the requirements of§ 25.222 (a)(1)(ii)(B).
5. Sea Tel hereby declares that the antennas referenced in paragraph 3 above, will automatically cease
transmission within 100 milliseconds if the pointing error should exceed 0.5 degrees and will not
resume transmission until the error drops below 0.2 degrees, thus meeting the requirements of §
25.222 (a)(1)(iii).
6. Sea Tel maintains all relevant test data, which is available upon request, to verify these declarations.
Peter Blaney, Chief Engineer
Sea Tel, Inc
Concord, CA

Table of Contents
v
1. INTRODUCTION ..........................................................................................................................................................................................1-1
1.1. GENERAL SYSTEM DESCRIPTION................................................................................................................................................................. 1-1
1.2. PURPOSE ..........................................................................................................................................................................................................1-1
1.3. OTHER INPUTS TO THE SYSTEM.................................................................................................................................................................. 1-1
1.4. SYSTEM COMPONENTS ................................................................................................................................................................................. 1-1
1.5. DUAL ANTENNA CONFIGURATION............................................................................................................................................................. 1-2
1.6. DUAL ANTENNA ARBITRATOR.....................................................................................................................................................................1-3
1.7. OPEN ANTENNA-MODEM INTERFACE PROTOCOL (OPENAMIP™) SPECIFICATION:........................................................................ 1-3
1.7.1. Overview: ........................................................................................................................................................................................1-3
1.7.2. Interface requirements:.........................................................................................................................................................1-4
2. SITE SURVEY..................................................................................................................................................................................................2-1
2.1. SITE SELECTION ABOARD THE SHIP .......................................................................................................................................................... 2-1
2.2. ANTENNA SHADOWING (BLOCKAGE)AND RF INTERFERENCE .............................................................................................................. 2-1
2.3. MOUNTING FOUNDATION ...........................................................................................................................................................................2-2
2.3.1. Mounting on Deck or Deckhouse......................................................................................................................................2-2
2.3.2. ADE Mounting Considerations...........................................................................................................................................2-2
2.3.3. Sizing of the support pedestal............................................................................................................................................2-2
2.4. MOUNTING HEIGHT AND FORE-AFT LOCATION ..................................................................................................................................... 2-3
2.5. MAST CONFIGURATIONS .............................................................................................................................................................................2-4
2.5.1. Vertical Masts ..............................................................................................................................................................................2-4
2.5.2. Raked Masts..................................................................................................................................................................................2-4
2.5.3. Girder Masts .................................................................................................................................................................................2-5
2.5.4. Truss Mast .....................................................................................................................................................................................2-5
2.6. SAFE ACCESS TO THE ADE.......................................................................................................................................................................... 2-5
2.7. BELOW DECKS EQUIPMENT LOCATION ..................................................................................................................................................... 2-5
2.8. CABLES.............................................................................................................................................................................................................2-6
2.8.1. ADE/BDE Coaxial Cables........................................................................................................................................................2-6
2.8.2. Antenna Power Cable ..............................................................................................................................................................2-6
2.8.3. Air Conditioner Power Cable ...............................................................................................................................................2-6
2.8.4. ACU Power Cable/Outlet........................................................................................................................................................2-7
2.8.5. Gyro Compass Cable................................................................................................................................................................2-7
3. INSTALLATION.............................................................................................................................................................................................3-1
3.1. GENERAL CAUTIONS &WARNINGS ........................................................................................................................................................... 3-1
3.2. UNPACKING THE BASE FRAME AND REFLECTOR CRATE ......................................................................................................................... 3-2
3.2.1. Installing the Ku-Band Co-Pol/Cross-Pol Feed Assembly ....................................................................................3-5
3.3. ASSEMBLING THE ADE.................................................................................................................................................................................3-9
3.3.1. Preparing for Assembly of the ADE .................................................................................................................................3-9
3.3.2. Sub-assemble the Base Frame Assembly...................................................................................................................3-10
3.3.3. Sub-assemble the bottom panels of the 144” Radome Assembly................................................................3-11
3.3.4. Sub-assemble the upper panels of the 144” Radome Assembly ...................................................................3-14
3.3.5. Sub-assemble the bottom panels onto the base frame .....................................................................................3-18
3.3.6. Installing the Marine Air Conditioner..........................................................................................................................3-19
3.3.7. Sub-assemble the Antenna Pedestal............................................................................................................................3-19
3.3.8. Close the 144” Radome Assembly.................................................................................................................................3-23
3.3.9. Prepare the 144” Radome ADE for Lift........................................................................................................................3-25
3.4. INSTALLING THE ADE ................................................................................................................................................................................3-26
3.4.1. Hoist...............................................................................................................................................................................................3-26
3.4.2. Install Antenna/Radome/Baseframe ............................................................................................................................3-26

Table of Contents
vi
3.5. INSTALLING THE BELOW DECKS EQUIPMENT. .......................................................................................................................................3-27
3.5.1. General Cautions & Warnings..........................................................................................................................................3-27
3.5.2. Preparing BDE Location...................................................................................................................................................... 3-27
3.5.3. System Configuration..........................................................................................................................................................3-27
3.5.4. Installing the Below Deck Equipment......................................................................................................................... 3-28
3.6. CONNECTING THE BELOW DECKS EQUIPMENT .....................................................................................................................................3-28
3.6.1. Connecting the ADE AC Power Cable......................................................................................................................... 3-28
3.6.2. Connecting the BDE AC Power Cables....................................................................................................................... 3-28
3.6.3. Connecting the ADE IF Coaxes...................................................................................................................................... 3-28
3.6.4. Connect the Modem TXIF Coax.................................................................................................................................... 3-28
3.6.5. Antenna Control Unit Connections.............................................................................................................................. 3-28
3.6.6. Radio Control Serial Cable................................................................................................................................................. 3-29
3.6.7. Terminal Mounting Strip (TMS) Connections ......................................................................................................... 3-29
3.6.8. Other BDE connections ...................................................................................................................................................... 3-32
3.7. FINAL CHECKS..............................................................................................................................................................................................3-32
3.7.1. Visual/Electrical inspection...............................................................................................................................................3-32
3.7.2. Electrical - Double check wiring connections......................................................................................................... 3-32
3.8. POWER-UP...................................................................................................................................................................................................3-32
3.9. CABLE TERMINATIONS...............................................................................................................................................................................3-33
3.9.1. At The Radome........................................................................................................................................................................3-33
3.9.2. ACU & TMS ................................................................................................................................................................................ 3-33
3.9.3. Other BDE ..................................................................................................................................................................................3-33
3.10. FINAL ASSEMBLY.........................................................................................................................................................................................3-33
3.10.1. Remove Stow Braces/Restraints..................................................................................................................................... 3-33
3.10.2. Verify all assembly and Wiring connections............................................................................................................ 3-33
3.11. POWER-UP THE ADE.................................................................................................................................................................................3-33
3.11.1. Initialization.............................................................................................................................................................................. 3-33
3.11.2. Home Flag Position...............................................................................................................................................................3-33
3.11.3. BDE ................................................................................................................................................................................................3-33
3.11.4. Balancing the Antenna........................................................................................................................................................3-34
3.11.5. Fine Balance and Monitoring Motor Drive Torque .............................................................................................. 3-34
3.12. SETUP ............................................................................................................................................................................................................3-36
4. BASIC SETUP OF THE ACU ..................................................................................................................................................................4-1
4.1. OPERATOR SETTINGS.....................................................................................................................................................................................4-1
4.2. SETUP PARAMETER DISPLAY AND ENTRY MENUS.................................................................................................................................4-1
4.3. DEFAULT SETUP PARAMETERS FOR YOUR ANTENNA...............................................................................................................................4-1
4.4. TRACK DISP .................................................................................................................................................................................................4-2
5. SETUP – SHIPS GYRO COMPASS...................................................................................................................................................... 5-1
5.1. GYRO TYPE ......................................................................................................................................................................................................5-1
5.2. UPDATING THE GYRO TYPE PARAMETER ................................................................................................................................................5-1
5.3. IF THERE IS NO SHIPS GYRO COMPASS.....................................................................................................................................................5-1
6. SETUP - BAND SELECT .........................................................................................................................................................................6-1
6.1. TRACK DISP .................................................................................................................................................................................................6-1
7. SETUP – TRACKING RECEIVER – VSAT.......................................................................................................................................7-1
7.1. DETERMINING THE IF TRACKING FREQUENCY (MHZ)...........................................................................................................................7-1
7.2. KHZ...................................................................................................................................................................................................................7-1
7.3. FEC...................................................................................................................................................................................................................7-1
7.3.1. L-Band SCPC Receiver.............................................................................................................................................................7-1

Table of Contents
vii
7.4. TONE ................................................................................................................................................................................................................7-1
7.4.1. VSAT Application........................................................................................................................................................................7-1
7.5. VOLT.................................................................................................................................................................................................................7-2
7.5.1. VSAT Application........................................................................................................................................................................7-2
7.6. SAT SKEW ....................................................................................................................................................................................................7-2
7.7. NID..................................................................................................................................................................................................................7-2
8. SETUP – HOME FLAG OFFSET.............................................................................................................................................................8-1
8.1. ELECTRONIC CALIBRATION OF RELATIVE ANTENNA POSITION (HOME FLAG OFFSET) ................................................................... 8-1
8.1.1. You Found a Large AZ TRIM value: ..................................................................................................................................8-1
8.1.2. You Observe “Home” Pointing is LEFT of the Bow-line: .........................................................................................8-2
8.1.3. You Observe “Home” Pointing is RIGHT of the Bow-line: .....................................................................................8-2
8.1.4. To Enter the HFO value in the DAC_2202:...................................................................................................................8-3
9. SETUP – TARGETING................................................................................................................................................................................9-1
9.1. AUTO TRIM.................................................................................................................................................................................................9-1
9.2. MANUALLY OPTIMIZING TARGETING........................................................................................................................................................ 9-1
9.3. EL TRIM .........................................................................................................................................................................................................9-2
9.4. AZ TRIM........................................................................................................................................................................................................9-2
9.5. SAVE NEW PARAMETERS.............................................................................................................................................................................. 9-2
10. SETUP – SEARCHING.............................................................................................................................................................................10-1
10.1. SEARCHING OPERATION .............................................................................................................................................................................10-1
10.1.1. Default Standard (Box) Search Pattern.......................................................................................................................10-1
10.1.2. Inclined Orbit Search Pattern..........................................................................................................................................10-2
10.1.3. No Gyro Search Pattern ......................................................................................................................................................10-3
10.2. CHANGING THE SEARCH PARAMETERS ....................................................................................................................................................10-4
10.2.1. AUTO THRES .............................................................................................................................................................................10-4
10.2.2. EL STEP SIZE ............................................................................................................................................................................10-4
10.2.3. AZ STEP SIZE ...........................................................................................................................................................................10-4
10.2.4. STEP INTEGRAL.......................................................................................................................................................................10-4
10.2.5. SEARCH INC..............................................................................................................................................................................10-5
10.2.6. SEARCH LIMIT.........................................................................................................................................................................10-5
10.2.7. SEARCH DELAY ........................................................................................................................................................................10-5
10.2.8. SWEEP INC ................................................................................................................................................................................10-5
10.3. SAVE NEW PARAMETERS............................................................................................................................................................................10-5
11. SETUP – BLOCKAGE & RF RADIATION HAZARD ZONES ..............................................................................................11-1
11.1. RADIATION HAZARD AND BLOCKAGE MAPPING (AZ LIMIT PARAMETERS)...................................................................................11-1
11.2. SAVE NEW PARAMETERS............................................................................................................................................................................11-4
12. SETUP – MODEM CONNECTIONS, SETUP AND TEST .....................................................................................................12-1
12.1. JUMPER SELECTION .....................................................................................................................................................................................12-1
12.2. IDIRECT MODEMS ......................................................................................................................................................................................12-2
12.3. COMTECH MODEMS...................................................................................................................................................................................12-2
12.4. HUGHES MODEMS ......................................................................................................................................................................................12-3
12.5. STM MODEMS............................................................................................................................................................................................12-3
12.6. CONNECTIONS (ACU TO SATELLITE MODEM)......................................................................................................................................12-3
12.6.1. iDirect Modems .......................................................................................................................................................................12-3
12.6.3. Hughes Modems .....................................................................................................................................................................12-3
12.6.4. STM Modems...........................................................................................................................................................................12-4
12.7. SYSTEM TYPE PARAMETER.....................................................................................................................................................................12-4
12.8. BLOCKAGE SIMULATION TEST -DAC-2202 ......................................................................................................................................12-5

Table of Contents
viii
12.8.1. Blockage Simulation Test - SW2 Trigger State: Logic Level LOW ................................................................ 12-5
12.8.2. Blockage Simulation Test - SW2 Trigger State: Logic Level HIGH .............................................................. 12-6
12.9. TESTING THE SATELLITE MODEM LOCK INPUT -DAC-2202.........................................................................................................12-6
12.10. SAVE NEW PARAMETERS ...........................................................................................................................................................................12-7
13. SETUP –OPTIMIZING KU-BAND POLARITY AND CROSS-POL ISOLATION..................................................... 13-1
13.1. POLARITY ANGLE (POLANG) PARAMETERS ..........................................................................................................................................13-1
13.2. OPTIMIZING AUTO-POLARIZATION ON RECEIVE SIGNAL ...................................................................................................................13-1
13.3. OPTIMIZING AUTO-POLARIZATION CROSS-POL ISOLATION .............................................................................................................13-2
13.4. SAVE NEW PARAMETERS ...........................................................................................................................................................................13-2
14. SETUP – OTHER PARAMETERS ....................................................................................................................................................... 14-1
14.1. SETUP PARAMETER DISPLAY AND ENTRY MENUS................................................................................................................................14-1
14.2. 5V OFFSET &SCALE..............................................................................................................................................................................14-1
14.3. REMOTE COMMAND............................................................................................................................................................................14-1
14.4. REMOTE MONITOR...............................................................................................................................................................................14-1
14.5. TO DISABLE/ENABLE DISHSCAN®..........................................................................................................................................................14-1
14.6. SATELLITE REFERENCE MODE ...................................................................................................................................................................14-1
14.7. REMOTE PARAMETERS .......................................................................................................................................................................14-2
15. ANTENNA SPECIFIC OPERATION................................................................................................................................................15-1
15.1. SYSTEM POWER-UP ....................................................................................................................................................................................15-1
15.2. ANTENNA INITIALIZATION........................................................................................................................................................................15-1
15.3. REFLECTOR A/REFLECTOR BSELECTION ...............................................................................................................................................15-2
15.4. TRACKING /BAND SELECTION..................................................................................................................................................................15-2
15.5. MANUALLY TARGETING ADIFFERENT SATELLITE ................................................................................................................................15-2
16. FUNCTIONAL TESTING .......................................................................................................................................................................16-1
16.1. ACU /ANTENNA SYSTEM CHECK ...........................................................................................................................................................16-1
16.2. LATITUDE/LONGITUDE AUTO-UPDATE CHECK .....................................................................................................................................16-1
16.3. HEADING FOLLOWING................................................................................................................................................................................16-1
16.4. AZIMUTH &ELEVATION DRIVE................................................................................................................................................................16-1
16.5. FOUR QUADRANT TRACKING TEST..........................................................................................................................................................16-2
16.6. BLOCKAGE SIMULATION TEST..................................................................................................................................................................16-3
16.7. TEST BROADBAND OPERATION ................................................................................................................................................................16-3
16.8. TEST VOICE OVER IP (VOIP) OPERATION ............................................................................................................................................16-3
17. INSTALLATION TROUBLESHOOTING........................................................................................................................................ 17-1
17.1. TROUBLESHOOTING THE ACU..................................................................................................................................................................17-1
17.1.1. ACU display is blank..............................................................................................................................................................17-1
17.1.2. ACU Status displays "REMOTE NOT RESPONDING"............................................................................................ 17-1
17.2. TROUBLESHOOTING SHIPS GYRO COMPASS PROBLEMS ......................................................................................................................17-2
17.2.1. STEP-BY-STEP........................................................................................................................................................................... 17-2
17.2.2. 1:1 SYNCHRO............................................................................................................................................................................17-2
17.2.3. 360:1 Synchro..........................................................................................................................................................................17-3
17.3.1. Theory Of Stabilization Operation ................................................................................................................................ 17-3
17.3.2. Series 9711 Antenna Initialization ............................................................................................................................... 17-4
17.3.3. Troubleshooting using DacRemP .................................................................................................................................. 17-4
17.3.4. Antenna Loop Error Monitoring..................................................................................................................................... 17-5
17.3.5. Reference Sensor Monitoring.......................................................................................................................................... 17-6
17.3.6. Open Loop Rate Sensor Monitoring............................................................................................................................. 17-8
17.3.7. Fine Balance and Monitoring Motor Drive Torque .............................................................................................. 17-9
17.3.8. Open Loop Motor Test ......................................................................................................................................................17-10

Table of Contents
ix
17.3.9. To Disable/Enable DishScan® ......................................................................................................................................17-11
17.3.10. Satellite Reference Mode ................................................................................................................................................17-11
17.3.11. To Read/Decode an ACU Error Code 0008 (Pedestal Function Error):...................................................17-11
17.3.12. Remote GPS LAT/LON Position:....................................................................................................................................17-14
18.MAINTENANCE .........................................................................................................................................................................................18-1
18.1. WARRANTY INFORMATION........................................................................................................................................................................18-1
18.2. TORQUE AND LOCTITE SPECIFICATIONS.................................................................................................................................................18-2
18.3. GENERAL MAINTENANCE ...........................................................................................................................................................................18-2
18.3.1. Balancing the Antenna.........................................................................................................................................................18-2
18.3.2. Fine Balance and Monitoring Motor Drive Torque...............................................................................................18-3
18.3.3. To Reset/Reinitialize the Antenna:.................................................................................................................................18-4
18.4. 400MHZ MODEM CONFIGURATION......................................................................................................................................................18-5
18.5. 400 MHZ LED INDICATORS.....................................................................................................................................................................18-6
18.6. 400 MHZ MODEM SIGNALS ....................................................................................................................................................................18-6
18.6.1. Pedestal M&C ...........................................................................................................................................................................18-6
18.6.2. Radio M&C..................................................................................................................................................................................18-7
18.6.3. Channel Identification.........................................................................................................................................................18-7
18.7. TROUBLESHOOTING 400MHZ MODEM COMMUNICATION FAULTS................................................................................................18-8
18.7.1. 400MHz Modem Queries: ..................................................................................................................................................18-8
18.7.2. Modem Query Methods......................................................................................................................................................18-8
18.7.3. Isolating a 400 MHz Modem Fault Procedure:....................................................................................................18-10
18.8.1. Installing the Ku-Band Co-Pol/Cross-Pol Feed Assembly ..............................................................................18-13
18.8.2. Calibrating the Ku-Band Co-Pol/Cross-Pol Feed Assembly ...........................................................................18-18
18.9. PEDESTAL CONTROL UNIT CONFIGURATION (MK2) ........................................................................................................................18-21
18.9.1. To configure the PCU; .......................................................................................................................................................18-21
18.9.2. Model Configuration Numbers.....................................................................................................................................18-21
19. STOWING THE ANTENNA..................................................................................................................................................................19-1
19.1. INSTALLING THE STOW RESTRAINTS .......................................................................................................................................................19-1
20. BLUETOOTH INSTALLATION & OPERATION ........................................................................................................................20-1
20.1. PREREQUISITES.............................................................................................................................................................................................20-1
20.2. INSTALLING THE ADE BLUETOOTH HARDWARE....................................................................................................................................20-1
20.3. INSTALLING THE BDE BLUETOOTH HARDWARE ....................................................................................................................................20-2
20.4. DIAGNOSTIC MODE ....................................................................................................................................................................................20-2
20.5. REMOVING THE ADE BLUETOOTH HARDWARE .....................................................................................................................................20-3
20.6. REMOVING THE BDE BLUETOOTH HARDWARE......................................................................................................................................20-3
20.7. INSTALLING SOFTWARE VIA BLUETOOTH ...............................................................................................................................................20-3
20.8. NORMAL OPERATION MODE......................................................................................................................................................................20-4
21. 9711-92 TECHNICAL SPECIFICATIONS ..................................................................................................................................21-1
21.1. 9711-92 SPECIFICATIONS.......................................................................................................................................................................21-1
21.2. CABLES...........................................................................................................................................................................................................21-8
21.2.1. Antenna Control Cable (Provided from ACU-MUX)..............................................................................................21-8
21.2.2. Antenna Transmit & Receive IF Coax Cables (Customer Furnished)..........................................................21-8
21.2.3. Multi-conductor Cables (Customer Furnished)......................................................................................................21-9
21.2.4. AC Power Cable (Pedestal and Rf Equipment)........................................................................................................21-9
21.2.5. AC Power Cable (Optional Marine Air Conditioner) .............................................................................................21-9
21.2.6. Gyro Compass Interface Cable (Customer Furnished) ......................................................................................21-9
22. DRAWINGS ...................................................................................................................................................................................................22-1
22.1. 9711-92 MODEL SPECIFIC DRAWINGS ................................................................................................................................................22-1

Table of Contents
x
22.2. 9711 GENERAL DRAWINGS......................................................................................................................................................................22-1
This Page Intentionally Left Blank

9711-92 Ku-Band TXRX Introduction
1-1
1. Introduction
WARNING: RF Radiation Hazard -This stabilized antenna system is designed to be used with
transmit/receive equipment manufactured by others. Refer to the documentation supplied by the
manufacturer which will describe potential hazards, including exposure to RF radiation, associated with
the improper use of the transmit/receive equipment. Note that the transmit/receive equipment will
operate independently of the stabilized antenna system.
The ultimate responsibility for safety rests with the facility operator and the individuals who
work on the system.
1.1. General System Description
Your system includes a fully stabilized antenna that has been designed and manufactured so as to be inherently
reliable, easy to maintain, and simple to operate. The equipment essentially permits unattended operation except for
start-ups or when changing to different transponders, or satellites.
1.2. Purpose
This shipboard Transmit-Receive (TXRX) system provides you with two-way satellite voice/data broadband
communications while underway on an ocean-going vessel. This can be used to provide a wide variety of telephone,
fax and high speed data applications. Your antenna system can transmit to and receive from any desired C-band
satellite which has adequate signal coverage in your current geographic area. This input will be distributed to your
satellite modem and then to all of your other below decks computer, fax and telephone equipment.
1.3. Other Inputs to the System
Multi-conductor cables from Ship’s Gyro Compass, GPS, phone, fax and computer equipment may be connected in the
system.
1.4. System Components
The Series 11 TXRX system consists of two major groups of equipment; an above-decks group and a below-decks
group. Each group is comprised of, but is not limited to, the items listed below. All equipment comprising the Above
Decks is incorporated inside the radome assembly and is integrated into a single operational entity. For inputs, this
system requires only an unobstructed line-of-sight view to the satellite, Gyro Compass input and AC electrical power.
For more information about these components, refer to the Basic System Information section of this manual.
A. Above-Decks Equipment (ADE) Group
1. Stabilized antenna pedestal
2. Antenna Reflector
3. Feed Assembly with LNB(s)
4. C-Band RF Equipment which may include C-Band High Power Amplifier(s)
5. Radome Assembly
B. Below-Decks Equipment Group
1. Antenna Control Unit
2. Splitter with desired number of outputs (one output to the ACU and one output to the Satellite Modem are
required).
3. Satellite Modem and other below decks equipment required for the desired communications purposes.
4. Spectrum Analyzer (Optional)
5. Control, RF and Other cable connections

Introduction 9711-92 Ku-Band TXRX
1-2
Figure 1 -1 Series 11 TXRX Simplified Block Diagram
1.5. Dual Antenna Configuration
Sometimes, due to very large blockage conditions, you may need to install a dual antenna configuration to provide
uninterrupted services. Two full antenna systems are installed and the ACU control outputs are connected to an
arbitrator switch panel which then is connected to the below decks equipment. NOTE: The RXIF from EACH antenna
MUST be connected to the RF IN (J6) on the rear panel of its respective ACU then RFOUT (J7) is connected to the RXIF
input of the Dual Antenna Arbitrator. This connection scheme is required for ACU “A” to be able to control Antenna
“A” (and ONLY Antenna “A”) AND ACU “B” to be able to control Antenna “B” (and ONLY Antenna “B”).
You will program the blockage zone(s) for each of the two antennas (refer to Setup – Blockage Zones). The blockage
output from the ACU is fed to the Terminal Mounting Strip so that the output of each ACU can be connected to the
arbitrator panel to control it. The blockage output is available on SW2 terminal of the Terminal Mounting Strip to
provide a transistor “short” to ground when the antenna is within a blockage zone programmed into the ACU. When
not blocked the SW2 terminal will be an “open”.
When one antenna is blocked, its blockage output will command the arbitrator panel to switch services to the modem
from that antenna to the other antenna. The arbitrator panel provides a logic latch to prevent excess switching when
the ship heading is yawing, therefore, causing if the antenna to be repeatedly blocked – unblocked – blocked.

9711-92 Ku-Band TXRX Introduction
1-3
1.6. Dual Antenna Arbitrator
The Dual Antenna Arbitrator panel can pass LNB voltages (and handle 250-400 ma of current) and the RXIF signals on
the RX connections. TXIF, Reference and BUC supply voltage can pass through this arbitrator panel to the antenna, but
it is not recommended that BUC power be supplied through the dual channel rotary joint of the antenna (a BUC power
supply is provided on all Series 09 antenna pedestals).
The blockage (SW2) output, GPS output and modem lock input from the two terminal mounting strips (antenna “A”
and antenna “B”) are wired through the arbitrator panel to the satellite modem. When antenna “A” is blocked, the
arbitrator PCB will toggle the coax switches so that antenna “B” provides signal to the BDE distribution (multi-switch or
modem). When antenna “A” is no longer blocked the arbitrator will do nothing (because it is a latch circuit). When
antenna “B” is blocked the panel will switch so that antenna “A” is again providing signal the BDE distribution.
To provide a seamless switching transition, refer to the arbitrator installation instructions to balance the TX and RX
signal levels between the two antennas.
1.7. Open Antenna-Modem Interface Protocol (OpenAMIP™) Specification:
1.7.1. Overview:
OpenAMIPTM, an ASCII message based protocol invented and Trademarked by iDirect is a specification for
the interchange of information between an antenna controller and a satellite modem. This protocol allows
the satellite modem to command the ACU (via TCP port 2002) to seek a particular satellite as well as allowing
exchange of information necessary to permit the modem to initiate and maintain communication via the
antenna and the satellite. In general, OpenAMIPTM is not intended for any purpose except to permit a
modem and the ACU to perform synchronized automatic beam switching. It is NOT a status logging system
or a diagnostic system. In addition, OpenAMIPTM is intended for a typical installation whereby a specific
satellite modem and Antenna system are properly configured to work together. The protocol does not make
specific provisions for auto-discovery or parameter negotiation. It is still the responsibility of the installer to
ensure that the parameters of both the satellite modem (proper option files) and the ACU/PCU (setup
parameters) are actually compatible for the intended satellite(s).

Introduction 9711-92 Ku-Band TXRX
1-4
1.7.2. Interface requirements:
1.7.2.1. Hardware
Sea Tel Antenna Control Units Model DAC-2202 or DAC-2302.
Any Satellite modem manufacturer that is compatible with OpenAMIPTM
CAT5 Patch cable
1.7.2.2. Software
Sea Tel model DAC-2202:
ACU software version 6.06 or greater
CommIF module software version 1.10f or greater
Sea Tel model DAC-2302:
ACU software version 7.06 or greater
CommIF module software version 1.10f or greater

9711-92 Ku-Band TXRX Site Survey
2-1
2. Site Survey
There are three objective of the site survey. The first is to find the best place to mount the antenna and the BDE. The second is
to identify the length and routing of the cables and any other items or materials that are required to install the system. The third
is to identify any other issues that must be resolved before or during the installation.
2.1. Site Selection Aboard The Ship
The radome assembly should be installed at a location aboard ship where:
•The antenna has a clear line-of-sight to view as much of the sky (horizon to zenith at all bearings) as is
practical.
•X-Band (3cm) Navigational Radars:
•The ADE should be mounted more than 0.6 meters/2 feet from 2kW (24 km) radars
•The ADE should be mounted more than 2 meters/8 feet from 10kW (72 km) radars
•The ADE should be mounted more than 4 meters/12 feet from 160kW (250km) radars
•S-Band (10cm) Navigational Radars:
•If the ADE is/has C-Band it should be mounted more than 4 meters/12 feet from the S-band Radar.
•The ADE should not be mounted on the same plane as the ship's radar, so that it is not directly in the
radar beam path.
•The ADE should be mounted more than 2.5 meters/8 feet from any high power MF/HF antennas
(<400W).
•The ADE should be mounted more than 4 meters/12 feet from any high power MF/HF antennas
(1000W).
•The ADE should also be mounted more than 4 meters/12 feet from any short range (VHF/UHF) antennae.
•The ADE should be mounted more than 2.5 meters/8 feet away from any L-band satellite antenna.
•The ADE should be mounted more than 3 meters/10 feet away from any magnetic compass installations.
•The ADE should be mounted more than 2.5 meters/8 feet away from any GPS receiver antennae.
•Another consideration for any satellite antenna mounting is multi-path signals (reflection of the satellite
signal off of nearby surfaces arriving out of phase with the direct signal from the satellite) to the
antenna. This is particularly a problem for the onboard GPS, and/or the GPS based satellite compass.
•The ADE and the BDE should be positioned as close to one another as possible. This is necessary to
reduce the losses associated with long cable runs.
•This mounting platform must also be robust enough to withstand the forces exerted by full rated wind
load on the radome.
•The mounting location is robust enough that it will not flex or sway in ships motion and be sufficiently
well re-enforced to prevent flex and vibration forces from being exerted on the antenna and radome.
•If the radome is to be mounted on a raised pedestal, it MUST have adequate size, wall thickness and
gussets to prevent flexing or swaying in ships motion. In simple terms it must be robust.
If these conditions cannot be entirely satisfied, the site selection will inevitably be a “best” compromise between the
various considerations.
2.2. Antenna Shadowing (Blockage) and RF Interference
At the transmission frequencies of C and Ku band satellite antenna systems, any substantial structures in the way of
the beam path will cause significant degradation of the signal. Care should be taken to locate the ADE so that it has
direct line-of-sight with the satellite without any structures in the beam path through the full 360 degree ships turn.
Wire rope stays, lifelines, small diameter handrails and other accessories may pass through the beam path in limited
numbers; however, even these relatively insignificant shadows can produce measurable signal loss at these
frequencies.

Site Survey 9711-92 Ku-Band TXRX
2-2
2.3. Mounting Foundation
2.3.1. Mounting on Deck or Deckhouse
While mounting the ADE on a mast is a common solution to elevate the ADE far enough above the various
obstructions, sometimes the best mounting position is on a deck or deckhouse top. These installations are
inherently stiffer than a mast installation as the design of the deck/deckhouse structure is prescribed by the
ship’s classification society. In the deck/deckhouse design rules, the minimum plating and stiffener guidelines
are chosen to preclude high local vibration amplitudes.
Most installations will have a base frame with multiple attachment points around the perimeter of the base
frame to mount the ADE onto a deck or deckhouse structure of the ship. The base frame may be mounted
using the supplied legs & braces to raise the ADE above the deck for radome hatch access. The base frame
may be directly attached to the deck, in which case the access panel in the floor of the base frame cannot be
utilized. In this case, the installation must allow acces through a door in one of the side panels or an access
opening directly under the hacth. Some care must be taken to ensure the mounting pedestal is properly
aligned with the stiffeners under the deck plating.
Alternately, a specifically designed and stiffened mast may be used to mount the base frame above the deck;
although, this should only be attempted if sufficient deck space high on the ship is not available.
2.3.2. ADE Mounting Considerations
Mounting the radome directly on the deck, or platform prevents access to the hatch in the base of the
radome unless an opening is designed into the mounting surface to allow such entry. If there is no access to
the hatch the only way to service the antenna is to remove the radome top.
Ladder rungs must be provided on all mounting stanchions greater than 3-4 feet tall to allow footing for
personnel safety when entering the hatch of the radome.
The recommended cable passage is through the bottom (near center) of the radome base, down through the
ADE support pedestal (if used), through the deck and into the interior of the ship.
2.3.3. Sizing of the support pedestal
The following should be taken into account when choosing the height of a mounting support stand:
1. The height of the pedestal should be kept as short as possible, taking into account recommendations
given in other Sea Tel Guidelines.
2. The minimum height of the pedestal above a flat deck or platform to allow access into the radome
for maintenance should be 0.6 meters (24 inches).
3. The connection of the ADE mounting plate to the stanchion and the connection of the pedestal to
the ship should be properly braced with triangular gussets (see graphic above). Care should be taken
to align the pedestal gussets to the ship’s stiffeners as much as possible. Doublers or other
reinforcing plates should be considered to distribute the forces when under-deck stiffeners are
inadequate.
4. The diameter of the pedestal stanchion shall not be smaller than 100 millimeters (4 inches). Where
the ADE base diameter exceeds 1.5 meters (60 inches), additional stanchions (quantity greater than
3) should be placed rather than a single large stanchion.
5. Shear and bending should be taken into account in sizing the ADE mounting plate and associated
gussets.
6. Shear and bending must be taken into account when sizing the pedestal to ship connection.
7. All welding should be full penetration welds –V-groove welds with additional fillet welds – with
throats equivalent to the thickness of the thinnest base material.
8. For an ADE mounted greater than 0.6 meters (24 inches) above the ship’s structure, at least one (1)
foot rung should be added. Additional rungs should be added for every 0.3 meter (12 inches) of
pedestal height above the ship’s structure.
9. For an ADE mounted greater than 3 meters (9 feet) above the ship’s structure, a fully enclosing cage
should be included in way of the access ladder, starting 2.3 meters (7 feet) above the ship’s
structure.

9711-92 Ku-Band TXRX Site Survey
2-3
2.4. Mounting Height and Fore-Aft Location
Installations with mast or deck vibrations at frequencies between 2 and 15 Hertz have been identified by Sea Tel as
causing problems with the isolation systems of the ADE. Preventing problems prior to installation due to these
vibrations is one of the primary considerations in choosing where to mount the antenna.
In some installations, though, the combination of mounting height, fore-aft location and ship motion can impart
significant accelerations on the entire ADE. Installations where the ADE is situated high on the ship – usually at the
top of a mast – places the ADE is a position where the low frequency ship motion in roll and/or pitch creates two
accelerations – tangential and radial. These accelerations vary in a periodic function, out-of-phase from the ship
response to the wave motions.
Radial acceleration is the acceleration acting on the mass of the ADE pulling away from the center of the axis (roll or
pitch). In this sense, it would be a force trying to ‘pull’ the ADE away from the ship. We normally are not too
concerned with radial acceleration, since it must become far greater than gravity to have a detrimental effect on the
ADE.
Tangential acceleration is the acceleration acting on the mass of the ADE pulling across the center of the axis (roll or
pitch). This acceleration becomes a force trying to pull the ADE to the side. The tangential acceleration has an effect
on both the strength of the ADE pedestal and the tracking accuracy of the control algorithm.
The effect of tangential acceleration is felt by the structure of the ADE before it truly affects the tracking accuracy.
For instance, Sea Tel normally accepts that a tracking error of 0.1 degrees RMS at 0.5 G to be within acceptable error
margins. A 0.5 G tangential acceleration on the ADE means that ½ of the weight of the ADE is acting sideways on the
pedestal structure.
The higher up you mount the antenna above the pivot point of the ship the higher the tangential acceleration (g-
force) exerted on the antenna will be (see chart below). When the g-force exerted on the antenna is light, antenna
stabilization and overall performance will not be affected.
If the g-force exerted on the antenna is high enough (> 1 G), antenna stabilization and overall performance will be
affected.
If the g-force exerted on the antenna is excessive (1-2 Gs), the antenna will not maintain stabilization and may even
be physically damaged by the g-force.

Site Survey 9711-92 Ku-Band TXRX
2-4
2.5. Mast Configurations
Sea Tel recommends the ADE be mounted on the ship in a location which has both a clear line-of-sight to the target
satellites in all potential azimuth/elevation ranges and sufficient support against vibration excitement. If possible,
mounting the ADE pedestal directly to ship deckhouse structures or other box stiffened structures is preferred.
However, in many cases, this imposes limits on the clear line-of-sight the antenna system has.
Often the solution for providing the full azimuth/elevation range the antenna needs is to mount the ADE on the ship’s
mast. Unfortunately, masts do not consider equipment masses in design and often have harmonic frequencies of their
own.
For these large systems, the mast for the ADE should be designed specifically for the ADE. Other equipment may be
mounted alongside, but the mast should be configured to accept the mass, loads and resonance of the ADE primarily.
The following sections describe various mast configurations and some considerations for mast design.
2.5.1. Vertical Masts
Vertical masts are a very ancient and common mast design. In essence, it is the mast derived from the sailing
mast and adapted for mounting the ever-increasing array of antennae which ships need to communicate with
the world. This drawing of a vertical mast shows
the preferred mounting of the ADE center-line
above the plane of the radar. Alternatively the ADE
is mounted below the plane of the radar signal
Vertical masts are most commonly found on cargo
ships – they are simple, inelegant and functional.
They are also fairly stiff against torsional reaction
and lateral vibrations, as long as the ADE is
mounted on a stiff pedestal near the vertical
centerline of the mast. If centerline mounting is
impractical or otherwise prohibited, the mast
platform the ADE is mounted on should be checked
for torsional vibration about the centerline of the
mast and the orthogonal centerline of the platform.
If the estimated natural frequency of the mast or platform is less than 35 Hertz, the mast or platform should
be stiffened by the addition of deeper gussets under the platform or behind the mast.
2.5.2. Raked Masts
Raked masts are found on vessels where the style
or appearance of the entire vessel is important.
Again, the inclined mast is a direct descendant from
the masts of sailing ships – as ship owners wanted
their vessels to look more unique and less
utilitarian, they ‘raked’ the masts aft to make the
vessel appear capable of speed. This drawing
shows a raked mast, again with the preferred ADE
mounting above the radar and alternate with the
ADE below the radar.
Raked masts pose special problems in both
evaluating the mast for stiffness and mounting of
antennae. As can be seen in the drawing, all
antennae must be mounted on platforms or other
horizontal structures in order to maintain the
vertical orientation of the antenna centerline. This
implies a secondary member which has a different
natural frequency than the raked mast’s natural frequency. In order to reduce the mass of these platforms,
they tend to be less stiff than the main box structure of the raked mast. Thus, they will have lower natural
frequencies than the raked mast itself. Unfortunately, the vibratory forces will act through the stiff structure
of the raked mast and excite these lighter platforms, to the detriment of the antenna.

9711-92 Ku-Band TXRX Site Survey
2-5
2.5.3. Girder Masts
Girder masts are large platforms atop a pair of
columns. Just like girder constructions in buildings,
they are relatively stiff athwart ship – in their
primary axis – but less stiff longitudinally and
torsionally. An example of a girder mast is shown in
this drawing, with the preferred ADE mounting
outboard and above the radar directly on one of the
columns and alternate with the ADE centered on
the girder above the plane of the radar.
The greatest weakness of girder masts is in torsion –
where the girder beam twists about its vertical
centerline axis. As with all mast designs discussed so far, mounting the antenna in line with the vertical
support structure will reduce the vibration tendencies. Mounting the antenna directly above the girder
columns provides ample support to the antenna pedestal and locates the antenna weight where it will
influence the natural frequency of the mast the least.
2.5.4. Truss Mast
Truss masts are a variant on the girder mast
concept. Rather than a pair of columns supporting a
girder beam, the construction is a framework of
tubular members supporting a platform on which
the antennae and other equipment are mounted. A
typical truss mast is shown in this photograph.
Like a girder mast, truss masts are especially stiff in
the athwart ship direction. Unlike a girder mast, the
truss can be made to be nearly as stiff in the
longitudinal direction. Truss masts are particularly
difficult to estimate the natural frequency – since a
correct modeling includes both the truss structure
of the supports and the plate/diaphragm structure
of the platform. In general, the following guidelines
apply when determining the adequate support for
mounting an antenna on a truss mast:
1. Antenna ADE pedestal gussets should align
with platform stiffeners which are at least
200 millimeters in depth and 10 millimeters in thickness.
2. When possible, the antenna ADE pedestal column should align with a vertical truss support.
3. For every 100 kilograms of ADE weight over 250 kilograms, the depth of the platform stiffeners
should be increased by 50 millimeters and thickness by 2 millimeters.
Sea Tel does not have a recommended arrangement for a truss mast – the variability of truss mast designs
means that each installation needs to be evaluated separately.
2.6. Safe Access to the ADE
Safe access to the ADE should be provided. Provisions of the ship’s Safety Management System with regard to men
aloft should be reviewed and agreed with all personnel prior to the installation. Installations greater than 3 meters
above the deck (or where the access starts at a deck less than 1 meter in width) without cages around the access
ladder shall be provided with means to latch a safety harness to a fixed horizontal bar or ring.
The access hatch for the ADE shall be oriented aft, or inboard, when practical. In any case, the orientation of the ADE
access hatch shall comply with the SMS guidelines onboard the ship. Nets and other safety rigging under the ADE
during servicing should be rigged to catch falling tools, components or fasteners.
2.7. Below Decks Equipment Location
The Antenna Control Unit, Terminal Mounting Strip and Base Modem Panel are all standard 19” rack mount, therefore,
preferred installation of these items is in such a rack. The ACU mounts from the front of the rack. The Terminal
Mounting Strip and Base Modem Panel mount on the rear of the rack.

Site Survey 9711-92 Ku-Band TXRX
2-6
The Satellite Modem, router, VIOP adapter(s), telephone equipment, fax machine, computers and any other associated
equipment should be properly mounted for shipboard use.
Plans to allow access to the rear of the ACU should be considered.
2.8. Cables
During the site survey, walk the path where the cables will be installed. Pay particular attention to how cables will be
installed; such as what obstacles they will be routed around, difficulties that will be encountered and the overall length
of the cables. The ADE should be installed using good electrical practice. Sea Tel recommends referring to IEC 60092-
352 for specific guidance in choosing cables and installing cables onboard a ship. Within these guidelines, Sea Tel will
provide some very general information regarding the electrical installation.
In general, all cable shall be protected from chaffing and secured to a cableway. Cable runs on open deck or down a
mast shall be in metal conduit suitable for marine use. The conduit shall be blown through with dry air prior to passing
cable to ensure all debris has been cleared out of the conduit and again after passing the cable to ensure no trapped
moisture exists. The ends of the conduit shall be sealed with cable glands (preferred), mastic or low VOC silicon
sealant after the cables have been passed through.
Cables passing through bulkheads or decks shall be routed through approved weather tight glands.
2.8.1. ADE/BDE Coaxial Cables
The first concern with the coaxial cables installed between the ADE & BDE is length. This length is used to
determine the loss of the various possible coax, Heliax or fiber-optic cables that might be used. You should
always provide the lowest loss cables to provide the strongest signal level into the satellite modem.
Signal cable shall be continuous from the connection within the ADE radome, through the structure of the
ship to the BDE. Splices, adapters or dummy connections will degrade the signal level and are discouraged.
Be careful of sharp bends that kink and damage the cable. Use a proper tubing bender for Heliax bends.
Penetrations in watertight bulkheads are very expensive, single cable, welded penetrations that must be
pressure tested.
Always use good quality connectors that are designed to fit properly on the cables you are using. Poor
quality connectors have higher loss, can allow noise into the cable, are easily damaged or fail prematurely.
In as much as is possible, don’t lay the coaxes on power cables. Try to have some separation from Inmarsat &
GPS cables that are also passing L-band frequencies or radar cables that may inject pulse repetition noise –as
error bits - into your cables.
2.8.2. Antenna Power Cable
Be cautious of length of the run, for voltage loss issues, and assure that the gauge of the wires is adequate for
the current that is expected to be drawn (plus margin). Antenna power is recommended (but not required) to
be from a UPS, generally the same one that supplies power to the below decks equipment.
Power cables shall comply with the provisions of IEC 60092-350 and -351 as practical. Power cables may be
routed through the same conduit as the signal cable from the junction box to the base of the ADE. Power
cables shall pass through separate radome penetrations from the signal cable.
The power cable shall be continuous from the UPS (or closest circuit breaker) to the ADE connections within
the radome. The power circuits shall be arranged so that ‘active,’ ‘common’ and ‘neutral’ (ground) legs are all
made or broken simultaneously. All circuit legs shall be carried in the same cable jacket.
2.8.3. Air Conditioner Power Cable
If your system includes a marine air conditioner, run an AC power cable to it from a breaker, preferably from a
different phase of the electrical system than that which supplies power to the ADE & BDE. Be EXTREMELY
cautious of length of the run for voltage loss and gauge of the wires for the current that is expected to be
drawn.
Power cable shall comply with the provisions of IEC 60092-350 and -351 in so far as practicable. Power
cable may be routed through the same conduit as the signal cable from the junction box to the base of the
ADE. Power cables shall pass through separate radome penetrations from the signal cable.
The power cable shall be continuous from the closest circuit breaker to the ADE connections within the
radome. The power circuits shall be arranged so that ‘active,’ ‘common’ and ‘neutral’ (ground) legs are all
made or broken simultaneously. All circuit legs shall be carried in the same cable jacket.