Sealey CP6018V User manual

© Jack Sealey Limited Original Language Version
INSTRUCTIONS FOR:
CORDLESS LITHIUM-ION HAMMER DRILL/DRIVER
18V SUPER TORQUE 1HR CHARGE - 2 BATTERIES
MODEL NO: CP6018V
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
Refer to
instruction
manual
Wear eye
protection
Wear ear
protection
Wear gloves
1. SAFETY
1.1. GENERAL SAFETY
9Disconnect the battery from the drill unit before changing accessories, servicing or performing any maintenance.
9Maintain the drill and battery in good condition. Check moving parts alignment on a regular basis.
9Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9Ensure the drill is switched off before installing the battery.
9Keep the drill battery and charger clean for best and safest performance.
9 Removeillttingclothing.Removeties,watches,ringsandotherloosejewelleryandcontainlonghair.
9 Evaluateyourworkingareabeforeusingthedrille.g.ceiling,oorsandenclosuresmaycontainelectricalitemsorwaterpiping.
9Ensure battery is correctly inserted into the drill handle and latched in place before attempting to switch on.
9Secure loose workpieces with a clamp, vice or other adequate holding device.
9Avoid unintentional starting.
9Wear approved safety eye protection (standard spectacles are not adequate).
9 Maintaincorrectbalanceandfooting.Ensuretheoorisnotslipperyandwearnon-skidshoes.
9Be aware that this drill does not need to be plugged into the mains power.
9Keep children and unauthorised persons away from the working area.
8DO NOTusethedrillwherethereareammableliquids,solidsorgases,suchaspaintsolvents,etc.
8DO NOT allow children to operate the drill.
8DO NOToperatethedrillifanypartsaremissingasthismaycausefailureorpossiblepersonalinjury.
8DO NOT hold unsecured workpiece in your hand.
8DO NOTcarrythedrillwithyourngeronthepowertrigger.
8DO NOT use the drill for a task it is not designed to perform.
8DO NOToperatethedrillwhenyouaretiredorundertheinuenceofalcohol,drugsorintoxicatingmedication.
8DO NOT get the drill, battery or charger wet or use in damp or wet locations.
9 Keepthedrill,batteryandchargerinasafe,dry,childproofareawherethetemperaturewillnotexceed104°F(40°C).
1.2. ELECTRICAL SAFETY
REGARDING DIRECT MAINS POWER USE WITH THE CHARGING BASE AND PLUG ONLY.
WARNING! It is the user’s responsibility to check the following:
1.2.1. Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer.
1.2.2. If the lamp is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
1.2.2.1. Electrical safety information. It is important that the following information is read and understood.
1.2.2.2. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.2.2.3. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.2.2.4. Important:Ensurethatthevoltageratingontheappliancesuitsthepowersupplytobeusedandthattheplugisttedwiththecorrect
 fuse-seefuseratingintheseinstructions.
8DO NOT pull or carry the appliance by the power cable.
8DO NOTpulltheplugfromthesocketbythecable.Removetheplugfromthesocketbymaintainingarmgripontheplug.
8DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
 qualiedelectrician.
CP6018VIssue:2(I)-14/01/16

1.2.3. Transformer Plug & BS Adaptor: The battery charger is supplied with a European standard Schuko plug. To use the battery charger
in the UK the BS adaptor must be used. Open the adaptor and insert the two pin plug on to the terminal connectors. Close the
adaptor over the plug mouldingandclampwithttedscrew.Seeillustrationontheright.
1.2.4. If the cable or plug is damaged during use, switch the electricity supply and remove from use.
1.2.5. ReplaceadamagedplugwithaBS1363/A13Amp3pinplug.Ifindoubtcontactaqualiedelectrician.
1.2.6. Class II products are wired with live (brown) and neutral (blue) only are marked with the Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
 Ensurethatthecableoutersheathextendsinsidethecablerestraintandthattherestraintistight.
8DO NOT connect either wire to the earth terminal.
1.2.7. Sealeyrecommendthatrepairsarecarriedoutbyaqualiedelectrician.
1.2.8. Battery Charger Safety Instructions
WARNING! DO NOT use the charging base to charge any battery other than that required for the tool. Other types of batteries may
explode!
9Inspect the plug, cable and the charging base for wear and damage to ensure items are safe before connecting to the mains power
supply. If worn or damaged DO NOTuse,immediatelyreplace,orcontactaqualiedelectrician.
9Check cables are always protected against short circuit and overload.
9Uncoil the power cable between the plug and the charging base before use.
8DO NOT pull or carry the charging base by the charger power lead, or pull the plug from the mains socket by the power lead.
8DO NOT use any other type of transformer with the charging base.
8DO NOTtrytoopenordis-assembletheplugorchargingbase.
8DO NOT use the plug to power any other electrical item.
9Disconnect the plug from the charging base and the mains power supply when not in use.
8DO NOTexposethechargingbasetodamporwetconditions(forindooruseonly).
8DO NOT pull or carry the charging base by the power lead.
8DO NOT operate the charging base if it has been dropped, or has received a sharp knock, or is damaged. Contact an authorised
service agent.
8DO NOTdismantlethechargingbaseasthismaycausedamageorpersonalinjuryandwillinvalidateyourwarranty.
8DO NOTinsertforeignobjectsormaterialintotheslotreservedforthebattery.
8DO NOTimmediatelychargeasecondbattery.Consecutivechargingwilloverheatthechargingbase.Allowtheunittocoolfor15
 minutesbeforechargingthenextbattery.
9Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9Ensure that cables are always protected against short circuit and overload.
8DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified
electrician.
1.2.9. Battery Safety Instructions
WARNING! Battery contains lithium-ion which is dangerous. Handle with care to avoid damage, re, corrosion or personal injury.
9 Chargebatterypriortoitsrstuse.Thebatterywillhavebeenshippedinalowchargestate.
To reduce the risk of burns or fire:
8DO NOT Attempt to open, disassemble, modify or service the battery pack.
8DO NOT Crush,puncture,shortexternalcontactsordisposeofinreorwater.
8DO NOT Exposetotemperaturesabove40°C(104°).
9Replace only with the battery pack designated for this product.
9Recycle or dispose of used battery as stipulated by local regulation.
9Use only the charging base provided to charge the drill battery.
8DO NOT attempt recharging the battery by means of an engine generator or a DC power source.
WARNING! Dispose of spent batteries correctly as they contain Lithium-ion. DANGER! DO NOT attempt to disassemble the battery.
For safety and environmental reasons DO NOT discard in domestic waste or by burning. ONLY discard or recycle according to local
authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person. If you come into contact with battery liquid take the following
immediate action:
a) Skin contact: Wash immediately with soap and water, then wash flesh in either lemon juice or vinegar.
b) Eye contact: Wash with a strong solution of boric acid, and seek immediate medical attention.
© Jack Sealey Limited Original Language Version CP6018VIssue:2(I)-14/01/16

2. INTRODUCTION
3. SPECIFICATION
Professionalheavy-dutyhammerdrillhasbeenergonomicallydesignedtoreduceoperatorfatigueandimprovecontrol.With18differenttorque
settings,makingthedrillsuitableforanumberofdifferentapplications.Built-inLEDlightenablesworktobecarriedoutindarkareas.13mmSingle
sleevechuckwithspindlelockforquickandeasybitchange.SuppliedwithtwoLithium-ionbatterieswhichallowforlongeroperationandaone
hour charge time.
Model No:.........................................................................CP6018V
Battery: .....................................................................18V1.5AhLi-ion 
No Load Speed: ..............................................................0-350/0-1400rpm 
Impact Rate: ................................................................0-4550/18200bpm 
Chuck Size .......................................................................... 13mm 
 MaximumTorque: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50Nm 
Replacement Battery: ............................................................. CP6018VBP 
Weight Including Battery: ................................................................2.4kg
Drilling Capacities:
Wood: .............................................................................. 32mm 
Metal: .............................................................................. 13mm 
Concrete: ........................................................................... 10mm
Chuck Size:
1
Battery "health" check
switch and LED's 4
3
5
2
6Fig. 1
8
Screwdriver bit holder
7Fig. 2
Dimples align with
grooves in drill neck
Rotatehandleanti-clockwisetot
drill neck, rotate handle clockwise to
clamp
Depth gauge thumb screw clamp
Handle
Fig. 3
Drill/screwandHammericons
Fig. 4
LED(torch)
"RELEASE/
GRIP"
Direction instruction.
Fig. 5
Fig. 7
Press down spring loaded
catch and slide out battery
in direction indicated.
Fig. 6
Slide off direction.
(replace opposite)
- +
Battery location
Green LED
Red
LED
© Jack Sealey Limited Original Language Version CP6018VIssue:2(I)-14/01/16

3. BATTERY CHARGING
Note:When new, the batteries will have been shipped in a low charge state. Fully charge the battery before using your tool
3.1 To remove the battery from the drill, see (Fig 6). DO NOT touch the metal battery terminals.
3.2 Take the base charger and plug it into the mains.
3.3 Thebatteryisdesignedtofitintothechargeronewayonly.Thisistoensurethatthepositive(+)andnegative(-)polaritiescorrespond.
Insert the battery fully and firmly to seatthebatteryintothechargingbase,asin(Fig.7).
3.4 WhenthebatteryisinsertedintothechargertheredLED(Fig.7)willilluminate,thisindicatesthebatteryischarging.
3.5 WhenthegreenLEDilluminates(Fig.7)batteryisfullycharged.Aonehourchargefromflat;lessfrompartiallycharged.
3.6 Remove the battery from the charger. Switch off and remove the plug from the mains. Push the battery back into the drill (Fig.6) until it
snaps into place. The drill is now ready for use.
Note: A special feature of the battery is a "health" indicator scale of charge. Depress the battery symbol switch on the battery, a scale of
 onetofourgreenLEDlightswillilluminatesee(Fig.1).
4. OPERATION
Note: If the drill is overloaded during use a protection device will operate to prevent damage. To continue, release the trigger and press again.
4.1 Withthedrillinthelockedmidpositionofthethreepositioncw/midlocked/acwdirectionchanger,see(Fig.2)legenditem9.
4.2 Openthechuckbyholdingthedrillandrotatingtheknurledchuckcollarinthedirectionmarked"RELEASE"acw(Fig.5)
4.3 Inserttherequireddrill/screwdriverbitintothefulllengthofthechuckandtightenbyholdingthedrillandrotatingtheknurledchuck 
 collarinthedirectionmarked"GRIP"cw(Fig.5).
4.4 Ensure correct drilling rotation direction by sliding the three position direction changer to the required position.
4.5 Thespeedofthedrilliscontrolledbythedrilltriggerappliedpressure,rangingfromzerotomaximumspeed.Thiscontrolis 
 independentofthe"HI"and"LOW"speedslidingswitchsituatedinthetopofthedrillbody.ThetorchLED(Fig.5)alsoilluminates.
4.6 Thetorquesetting"1"isminimumand"18"ismaximum.Acombinationofvariablespeedandtorquegivesmaximumdrillingefficiency.
 (Notavailableonhammerdrillsettingwhichhasafixedtorquerating)
4.7FortasksettingsDrillorHammerdrill,see(Fig.4)icons.
4.8 On completion of tasks, remove bit from drill, clean all items and store in carry case.
1
2
4
4
5
6
7
38
9
10
12
11
Legendofdrillparts-:
1 KeylessØ13mmchuck
2 Variablespeed&torchtrigger
3 "HI"and"LOW"speedoptions
4 Battery(2supplied)
5 Depthgaugerod
6 Handle
7 Speedandtorquesettingring
8 Threepositionswitchcw/locked/acw
9 MainschargerleadandShukotwopinplug
10 BSAdaptor(forSchukotwopin)
11 Drillclip
12 Carrycase
© Jack Sealey Limited Original Language Version CP6018VIssue:2(I)-14/01/16

WARNING! – Risk of Hand Arm Vibration Injury.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
ThistoolissubjecttothevibrationtestingsectionoftheMachineryDirective2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): .........14.22 m/s²
Uncertainty value (k):...........................1.5 m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that a
specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool.
NB: StatedVibrationEmissionvaluesaretype-testvaluesandareintendedtobetypical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
Werecommendaprogrammeofhealthsurveillancetodetectearlysymptomsofvibrationinjurysothatmanagementprocedurescanbemodified
accordingly.
Personal protective equipment.
Wearenotawareofanypersonalprotectiveequipment(PPE)thatprovidesprotectionagainstvibrationinjurythatmayresultfromthe
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and
maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use and
Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSE website
www.hse.gov.uk-Hand-ArmVibrationatWork.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable) into
approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and
Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling information.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [e-mail] or telephone [phone].
NOTE: It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without
prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guaranteeis12monthsfrompurchasedate,proofofwhichwillberequiredforanyclaim.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP327AR
www.sealey.co.uk
© Jack Sealey Limited Original Language Version CP6018VIssue:2(I)-14/01/16