680KG FOLDING 360º ROTATING ENGINE
STAND WITH GEARED HANDLE DRIVE
MODEL NO: ES680D
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to when
using this equipment.
9Before using the stand ensure it is in good working order.
9Ensure the stand legs and arms are locked with respective pins and R clips before use.
9Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
8DO NOT use unit if damaged.
9Keep the stand clean for best and safest performance.
9Use only with legs folded down and pinned.
9Locate the stand in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate
lighting.
9 Useonarm,levelsurfacecapableofsustainingthestandandtheload.
9 Maintaincorrectbalanceandfooting.Ensuretheoorisnotslipperyandwearnon-slipshoes.
9 Ensureallnon-essentialpersonskeepasafedistancewhilstthestandisinuse.
9 Lockmountingplateinpositionwithlockingpinbeforexingaloadandensuretheloadiscentredandsecurelymountedonthe
mounting plate.
9When an engine is mounted, take the weight of the engine on the handle before removing the locking pin.
9Ensure the stand and load are stable.
9To move a loaded stand, steady the load and push from behind the main post of the stand so that the castor wheels are ahead of the
load.
8DO NOT pull the unit backwards, or push from the side, as this may cause the stand to tip.
8DO NOT concentrate a heavy load to either side or end of the Engine Stand. This can cause the balance to shift suddenly, tipping
the Engine Stand and its load which can quickly cause severe injury and property damage!
9Ensure surface over which the stand is to travel is strong enough to take the stand and load and that it is not cracked, uneven,
sloped or obstructed.
8DO NOT allow untrained persons to use the stand.
8DO NOTexceedtheratedcapacityof680kg.
8DO NOT use to support humans or animals.
8DO NOT climb on the Engine Stand.
▲DANGER! DO NOT work under an engine mounted on the stand.
8DO NOT use the stand for purposes other than those for which it is designed.
9When not in use store stand in a safe, dry, childproof area.
9 Useextremecautionwhilerotatingthehandcranktorotatetheloadasalarge,top-heavyengineorsimilarobjectcouldresultina
sudden imbalance condition and cause the Engine Stand to suddenly tip.
▲DANGER! While rotating, always stand behind the crank end of the stand and make constant observations of the casters. If any
indication of instability occurs, STOP IMMEDIATELY!
▲DANGER! PINCH/CRUSH HAZARD!ThisEngineStandhasmoveablecomponentsthatcancrushandpinch.Keepngersand
hands away from pinch points when operating.
2. INTRODUCTION
Thisenginestandacceptsawidevarietyofenginesandtransmissions.TheGearedHandleDriveallowsforeasyandaccurate360ºrotationin
order to access all parts of the engine. Mounting head has four fully adjustable arms with bolt holes to accommodate various load sizes. Fitted
withscrewlocktoensureloadissecured.Swivelcastorsprovideexcellentmanoeuvrability.Assembledwithclevispinsandclipssothestand
can be folded for storage. Maximum Load Length: 700mm.
3. SPECIFICATION
Model No:.................................................................ES680D
Capacity:...................................................................... 680kg
Original Language Version
© Jack Sealey Limited
Refer to
instructions Wear protective
gloves
Wear safety
footwear Wear protective
clothing Warning:
Pinch crush
hazard
ES680DIssue:205/09/23
Size(WxDxH): ..................................1080x895x890mm
Max.LoadLength:.......................................................700mm
