Sealey MK51.V2 User manual

Features fully adjustable arms to fit many styles of bonnets, wings, doors and bumpers. Main frame can adjust through 180°, to give required angle.
Fitted with two fixed Ø 180mm wheels and two braked Ø 125mm castors for easy manoeuvrability.
Specification
Overall Arm Width: .........935mm
Base Dimensions: ..........1110 x 780mm
Assemble panel stand according to the diagram overleaf.
INSTRUCTIONS FOR:
PANEL STAND -
DOOR, WING, BONNET & BUMPER
MODEL NO: MK51.V2
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
3. ASSEMBLY
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years
of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
 Only use on firm, level, unobstructed surfaces which are capable of supporting the stand and body panels.
 DO NOT overload.
 Always load evenly with the centre of gravity of the load as near the centre as possible.
 Apply the brakes before commencing work.
 DO NOT stand/ride on the stand, or allow others to do so.
 Replace or repair damaged parts. Use only recommended parts. Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING! Failure to comply with these instructions may result in loss of load, damage to the stand or other property and/or personal
injury.
WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions
and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.

01284 757500
01284 703534 [e-mail]
www.sealey.co.uk
Web
email
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
PARTS FOR:
PANEL STAND - DOOR/WING/BONNET/BUMPER
MODEL: MK51.V2
ITEM PART NO DESCRIPTION
1 MK51.V2-01 SIDE LEG (BASE TUBE)
2 MK51.V2-02 SCREW
3 MK51.V2-03 WASHER
4 MK51.V2-04 LOCK NUT
5 MK51.V2-05 SUPPORT FOR UPRIGHT (SET TUBE)
6 MK51.V2-06 KNOB
7 MK51.V2-07 UPRIGHT FRAME,SIDE (ERECT TUBE)
8 MK51.V2-08 SUPPORT FOR UPRIGHT (SET TUBE)
9 MK51.V2-09 UPRIGHT FRAME SUPPORT
(BOTTOM ERECT TUBE)
10 MK51.V2-10 UPRIGHT FRAME (TOP ERECT TUBE)
11 MK51.V2-11 LOCK PIN
12 MK51.V2-12 SIDE LEG (BASE TUBE)
ITEM PART NO DESCRIPTION
13 MK51.V2-13 WHEEL 175X37X13
14 MK51.V2-14 SNAP RING
15 MK51.V2-15 EXTENSION FRAME (CROSS TUBE)
16 MK51.V2-16 ADJUSTABLE ANGLE BRACKET
(ANGULAR DISC)
17 MK51.V2-17 EXTENSION FRAME
18 MK51.V2-18 WHEEL WITH BRAKE 122X25X11
19 MK51.V2-19 BASE SUPPORT (OBLIGUE TUBE)
20 MK51.V2-20 BASE SUPPORT (OBLIGUE TUBE)
21 MK51.V2-21 BUSHING
22 MK51.V2-22 SCREW (3/8x2-1/2")
Issue: 1
Issue Date: 080413