Sealey SL67S User manual

SL67S Issue:2-(5,10) 06/02/20
PLEASE SAVE THIS OWNER’S MANUAL AND READ
BEFORE USE. This manual will explain how to use
the unit safely and effectively. Please read and follow
these instructions and precautions carefully.
MODEL NO:
SL67S
Jump Starter Power
Pack 800A Peak Power
- Lithium

CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ............................ 3
PERSONAL PRECAUTIONS ............................................... 4
PREPARING TO USE THE UNIT......................................... 5
CONNECTING TO A BATTERY ........................................... 5
FEATURES............................................................................. 6
CHARGING THE JUMP STARTER...................................... 6
OPERATING INSTRUCTIONS............................................. 7
MAINTENANCE INSTRUCTIONS....................................... 9
STORAGE INSTRUCTIONS .............................................. 10
TROUBLESHOOTING ........................................................ 10
SPECIFICATIONS ................................................................11
SAFETY SYMBOLS
Refer to
instruction
manual
Warning!
Electricity
Warning!
Explosive
material
Wear eye
protection

• 3 •
1. IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
WARNING – RISK OF EXPLOSIVE GASES.
WORKING IN THE VICINITY OF A LEAD-
ACID BATTERY IS DANGEROUS. BATTERIES
GENERATE EXPLOSIVE GASES DURING
NORMAL OPERATION. IT IS IMPORTANT THAT
YOU FOLLOW THESE INSTRUCTIONS EACH TIME
YOU USE THE UNIT.
To reduce the risk of battery explosion, follow these
instructions and those published by the battery
manufacturer and the manufacturer of any equipment
you intend to use in the vicinity of a battery. Review
cautionary markings on these products and on the
engine.
WARNING! RISK OF ELECTRIC SHOCK OR FIRE.
1.1 Read the entire manual before using this product. Failure
to do so could result in serious injury or death.
1.2 Keep out of reach of children.
1.3 Do not put ngers or hands into any of the unit’s outlets.
1.4 Do not expose the unit to rain or snow.
1.5 Use only recommended attachments. Use of an
attachment not recommended or sold by Sealey for the
SL67S may result in a risk of re, electric shock or injury
to persons or damage to property.
1.6 To reduce the risk of damage to the electric plug or
cord, pull by the adaptor rather than the cord when
disconnecting the unit.
1.7 Do not operate the unit with damaged cables or clamps.
1.8 Do not operate the unit if it has received a sharp blow,
been dropped or otherwise damaged in any way; take it to
a qualied service person.
1.9 Do not disassemble the unit; take it to a qualied service
person when service or repair is required. Incorrect
reassembly may result in a risk of re or electric shock.
WARNING! RISK OF EXPLOSIVE GASES.
1.10 To reduce the risk of a battery explosion, follow
these instructions and those published by the battery
manufacturer and the manufacturer of any equipment
you intend to use in the vicinity of the battery. Review the
precautionary markings on these products and on the
engine.
1.11 Do not set the unit on ammable materials, such as
carpeting, upholstery, paper, cardboard, etc.
1.12 Never place the unit directly above battery being
jumped.

• 4 •
1.13 Do not use the unit to jump start a vehicle while charging the
internal battery.
2. PERSONAL PRECAUTIONS
WARNING! RISK OF EXPLOSIVE GASES. A SPARK
NEAR THE BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF A SPARK
NEAR THE BATTERY:
2.1 NEVER smoke or allow a spark or ame in the vicinity of a
battery or engine.
2.2 Remove personal metal items such as rings, bracelets,
necklaces and watches when working with a lead-acid
battery. A lead-acid battery can produce a short-circuit
current high enough to weld a ring to metal, causing a
severe burn.
2.3 Be extra cautious, to reduce the risk of dropping a
metal tool onto the battery. It might spark or short-circuit
the battery or other electrical part that may cause an
explosion.
2.4 Do not permit the internal battery of the unit to freeze.
Never charge a frozen battery.
2.5 To prevent sparking, NEVER allow clamps to touch
together or contact the same piece of metal.
2.6 Consider having someone nearby to come to your aid
when you work near a lead-acid battery.
2.7 Read the Material Safety Data Sheet available from www.sealey.
co.uk. In the event of an accident seek medical attention.
3. PREPARING TO USE THE UNIT
WARNING! RISK OF CONTACT WITH BATTERY
ACID. BATTERY ACID IS A HIGHLY CORROSIVE
SULPHURIC ACID.
3.1 Make sure the area around the battery is well ventilated
while the unit is in use.
3.2 Clean the battery terminals before using the jump starter.
During cleaning, keep airborne corrosion from coming
into contact with your eyes, nose and mouth. Use baking
soda and water to neutralize the battery acid and help
eliminate airborne corrosion. Do not touch your eyes,
nose or mouth.
3.3 Determine the voltage of the battery by referring to the
vehicle owner’s manual and make sure that the output
voltage is 12V.
3.4 Make sure that the unit’s cable clamps make tight
connections.

• 5 •
4. CONNECTING TO A BATTERY
WARNING! A SPARK NEAR THE BATTERY MAY CAUSE
A BATTERY EXPLOSION. TO REDUCE THE RISK OF A
SPARK NEAR THE BATTERY:
4.1 Plug the clamps into the unit, and then attach the output
cables to the battery and chassis as indicated below.
Never allow the output clamps to touch each other.
4.2 Position the DC cables to reduce the risk of damage by
the bonnet, door and moving or hot engine parts. NOTE:
If it is necessary to close the bonnet during the jump
starting process, ensure that the bonnet does not touch
the metal part of the battery clips or cut the insulation of
the cables.
4.3 Stay clear of fan blades, belts, pulleys and other parts that
can cause injury.
4.4 Check the polarity of the battery posts. The POSITIVE
(POS, P, +) battery post usually has a larger diameter
than the NEGATIVE (NEG, N, -) post.
4.5 Determine which post of the battery is grounded
(connected) to the chassis. If the negative post is
grounded to the chassis (as in most vehicles), see step
4.6. If the positive post is grounded to the chassis, see
step 4.7.
4.6 For a negative-grounded vehicle, connect the POSITIVE
(RED) clamp from the jump starter to the POSITIVE
(POS, P, +) ungrounded post of the battery. Connect
the NEGATIVE (BLACK) clamp to the vehicle chassis or
engine block away from the battery. Do not connect the
clamp to the carburettor, fuel lines or sheet-metal body
parts. Connect to a heavy gauge metal part of the frame
or engine block.
4.7 For a positive-grounded vehicle, connect the NEGATIVE
(BLACK) clamp from the jump starter to the NEGATIVE
(NEG, N, -) ungrounded post of the battery. Connect the
POSITIVE (RED) clamp to the vehicle chassis or engine
block away from the battery. Do not connect the clamp
to the carburettor, fuel lines or sheet-metal body parts.
Connect to a heavy gauge metal part of the frame or
engine block.
4.8 When nished using the jump starter, remove the clamp
from the vehicle chassis and then remove the clamp from
the battery terminal. Disconnect the clamps from the unit.

• 6 •
5. FEATURES
6. CHARGING THE JUMP STARTER
IMPORTANT! CHARGE IMMEDIATELY AFTER
PURCHASE, AFTER EACH USE AND EVERY 30
DAYS, OR WHEN THE CHARGE LEVEL FALLS
BELOW 85%, TO KEEP THE INTERNAL BATTERY
FULLY CHARGED AND PROLONG BATTERY LIFE.
6.1 CHECKING THE LEVEL OF THE INTERNAL
BATTERY
1. Slide the ON/OFF switch to the ON position. The LCD
display will show the battery’s percentage of charge. A fully
charged internal battery will read 100%. Charge the internal
battery if the display shows it is under 85%.
2. To reduce the risk of electric shock, unplug the unit’s
charging cable from a USB or wall charger before attempting
any maintenance or cleaning. Simply turning o󰀨 the controls
will not reduce this risk.
3. When charging the internal battery, work in a well ventilated
area and do not restrict the ventilation in any way.
1. Smart cable green and red
LEDs.
2. Smart cable/
battery clamps
3. ON/OFF switch
4. Micro USB input port
for recharging
5. 3.0A USB output port
6. 2.4A USB output port
7. Display button
8. LCD display
9. Jump start output socket
10. LED light
Not shown:
11. Micro USB-USB charging
cable (not shown)
12. Carrying bag (not shown)

• 7 •
6.2 CHARGING THE INTERNAL BATTERY
NOTE: Use a 2A USB charger (sold separately), or a 2A
USB charging port to quickly recharge the jump starter.
Using a charger with less than 2A will increase charge
time.
1. Plug the Micro USB end of the charging cable into the input
port. Next, plug the USB end of the charging cable into a
charger’s USB port.
2. Plug your charger into a live AC or DC power outlet.
3. The LCD display will light, the digit begins to ash and show
“IN”, indicating that charging has begun.
4. The jump starter will fully charge in 4-5 hours. When the
unit is fully charged, the display will show “100%”.
5. When the battery is fully charged, disconnect your charger
from the outlet, and then remove the charging cable from
the charger and the unit. Slide the ON/OFF switch to the
OFF position, if you are not using the unit immediately.
7. OPERATING INSTRUCTIONS
7.1 JUMP STARTING A VEHICLE ENGINE
IMPORTANT: Do not use the jump starter while charging its
internal battery.
IMPORTANT: Using the jump starter without a battery
installed in the vehicle will damage the vehicle’s electrical
system.
NOTE: The internal battery must have a charge of at
least 40% to jump start a vehicle.
1. Turn the ignition OFF.
2. Plug the battery clamp cable into the jump starter’s output
socket.
3. Lay the DC cables away from any fan blades, belts, pulleys
and other moving parts. Make sure all of the vehicle’s
electrical devices are turned o󰀨.
4. For a negative-grounded vehicle, connect the POSITIVE
(RED) clamp from the jump starter to the POSITIVE
(POS, P, +) ungrounded post of the battery. Connect
the NEGATIVE (BLACK) clamp to the vehicle chassis or
engine block away from the battery. Do not connect the
clamp to the carburettor, fuel lines or sheet-metal body
parts. Connect to a heavy gauge metal part of the frame
or engine block.
5. For a positive-grounded vehicle, connect the NEGATIVE
(BLACK) clamp from the jump starter to the NEGATIVE
(NEG, N, -) ungrounded post of the battery. Connect the
POSITIVE (RED) clamp to the vehicle chassis or engine
block away from the battery. Do not connect the clamp
to the carburettor, fuel lines or sheet-metal body parts.
Connect to a heavy gauge metal part of the frame or
engine block.

• 8 •
6. Slide the ON/OFF switch to the ON position. The green
LED on the smart cable should light.
NOTE: If the vehicle battery is extremely discharged, the
initial current draw from the jump starter may activate short
circuit protection in the smart cable. When the condition is
corrected, the smart cable will automatically reset.
7. After a proper connection has been made, crank the
engine. If the engine does not start within 5-8 seconds, stop
cranking and wait at least 1 minute before attempting to
start the vehicle again.
NOTE: If the car does not crank a second time, check
the smart cable to see if the green LED is lit. If an LED
is ashing, refer to section 10. When the condition is
corrected, the smart cable will automatically reset.
NOTE: Cold weather may a󰀨ect the performance of the
jump starter’s lithium battery. If you hear only a click and
the engine does not turn over, try the following:
With the jump starter connected to the car battery and the
green LED illuminated on the smart cable, turn on all lights
and electrical accessories for one minute. This draws current
from the jump starter and warms the battery. Now try to crank
the engine. If it does not turn over, repeat the procedure.
Extremely cold weather may require two or three battery
warmings before the engine will start.
IMPORTANT: DO NOT attempt to jump start your vehicle
more than three consecutive times. If the vehicle will not
start after three attempts, consult a service technician.
8. After the engine starts, unplug the battery clamps from the
jump starter socket and then disconnect the black clamp
(-) and the red clamp (+), in that order. Slide the ON/OFF
switch to the OFF position.
9. Recharge the unit as soon as possible after each use.
7.2 CHARGING A MOBILE DEVICE, USING THE USB
PORTS
The SL67S includes two USB ports. One provides up
to 2.4A at 5V DC; the other is Quick Charge 3.0™, which
provides up to 5V at 3A, 9V at 2A or 12V at 1.5A.
1. Consult your mobile device manufacturer for proper
charging power specications. Connect a mobile device
cable to the appropriate USB port.
2. Slide the ON/OFF switch to the ON position. Charging
should begin automatically. The display will show which
port is in use.
3. Charging time will vary, based on the mobile device’s
battery size and the charging port used.
NOTE: Most devices will charge with either USB port, but
may charge at a slower rate.
4. When nished using the USB port, disconnect the charging
cable from your mobile device and then disconnect the

• 9 •
charging cable from the unit. Slide the ON/OFF switch to
the OFF position.
5. Recharge the unit as soon as possible after each use.
NOTE: If no USB device is connected, power to the USB
ports will automatically shut o󰀨 after 30 seconds.
7.3 USING THE LED LIGHT
1. Slide the ON/OFF switch to the ON position.
2. Hold down the display button for 3 seconds.
3. Once the LED light is on, press and release the display
button to cycle through the following modes:
• Steady glow
• Flash for an SOS signal
• Flash in strobe mode
4. When nished using the LED light, press and hold the
display button until the light turns o󰀨.
5. Slide the ON/OFF switch to the OFF position.
6. Recharge the unit as soon as possible after each use.
8. MAINTENANCE INSTRUCTIONS
1. After use and before performing maintenance, unplug
and disconnect the unit.
2. Use a dry cloth to wipe all battery corrosion and other dirt
or oil from the battery clamps, cords, and the outer case.
3. Do not open the unit, as there are no user-serviceable
parts.
9. STORAGE INSTRUCTIONS
1. Charge battery to full capacity before storage.
2. Store this unit at temperatures between -4°F-+140°F
(-20°C-+60°C).
3. Never completely discharge the battery.
4. Charge after each use.
5. Charge at least once every month, if not in frequent use,
to prevent over-discharge.

• 10 •
10. TROUBLESHOOTING Jump Starter
PROBLEM SOLUTION
The jump starter’s display
will not turn on.
Make sure the unit is charged.
Connect to a power source, to
reset.
Make sure the ON/OFF switch is
set to the ON position.
The thermometer
symbol
is ashing.
The unit is too hot or cold. The
thermometer symbol will disappear
when the condition is removed.
The jump starter will not
recharge.
Make sure the power source is
live.
The jump starter turns
on, but won’t jump start
my vehicle.
Check connections.
Verify the charge level of the jump
starter is at least 40%.
Do not attempt to jump start
your vehicle more than three
consecutive times. If the vehicle
still does not start, consult a
qualied service technician.
When cable is connected
only to the battery: Solid
Red LED, (Green LED
o󰀨); beeps once per
second.
The vehicle battery voltage is
lower than 10.5V. User can
connect to the jump starter and
turn key to jump start the vehicle.
When the cable is
correctly connected to
both battery and jump
starter: Green LED
blinking: RED LED o󰀨; no
beep.
“Fake” high battery voltage is
detected but reverse protection
did not activate. User can turn
key to jump start the vehicle.

• 11 •
Smart Cable LED and Alarm Behavior
BEHAVIOUR REASON
Green LED blinking; Red
LED o󰀨; no beep.
Cable is connected to battery only.
Cable is connected to jump starter
only.
Green LED solid; Red
LED o󰀨; no beep.
Cable is connected correctly to
both battery and jump starter.
Solid Red LED, Green
LED o󰀨; beeps once per
second.
Low voltage protection.
Solid Red LED, Green
LED o󰀨; beeps twice per
second.
Reverse polarity protection.
Alternating Red and
Green ashing LEDs; no
beep.
Reverse charging protection.
Solid Red LED, Green
LED o󰀨; rapid beeping.
Short circuit protection.
Solid Red and Green
LEDs; no beep.
Auto shut-o󰀨, due to inactivity.
Disconnect and reconnect clamps
to the vehicle battery.
Solid Red and Green
LEDs; beeps once per
second.
Temperature protection.
NOTE: When the condition is corrected, the smart cable will
automatically reset.
11. SPECIFICATIONS
Auxiliary output: .............................................................
USB (x2) - 5V/2.4A, 5V/Quickcharge 3.0
Cable & clamp length:........................................440mm
Capacity:......................... 10Ah @ 3.2V, 2.5Ah@ 12.8V
Max. current:..........................................................800A
Max. starting capacity: ......................4L petrol/2L diesel
Size (W x D x H): ............................... 84 x 34 x 173mm
Voltage: ................................................................... 12V

• 12 •
Sealey Group, Kempson Way, Suffolk
Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500 01284 703534
[e-mail] www.sealey.
co.uk
WEEE REGULATIONS
Dispose of this product at the end of its working life in
compliance with the EU Directive on Waste Electrical
and Electronic Equipment (WEEE). When the product
is no longer required, it must be disposed of in an
environmentally protective way. Contact your local
solid waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of
them as waste. All tools, accessories and packaging
should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the
environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids
(if applicable) into approved containers and dispose of
the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such
we reserve the right to alter data, specifications and component
parts without prior notice.
Important: No Liability is accepted for incorrect use of this
product.
Warranty: Guarantee is 2 years from purchase date for the unit,
1 year for the battery. Proof of purchase is required for any claim.
Parts support is available for this product. To obtain parts,
please log on to
www.sealey.co.uk, email [e-mail] or telephone
01284 757500

• 13 •
EC DECLARATION
OF CONFORMITY
Description and Function:������������������������������������������������������������������������������������������������������������������������������������������������������������������������
Model/Type:���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
Manufacturing Date/Serial Number where applicable: ����������������������������������������������������������������������������������������������������������������������������
This declaration of conformity is issued under the sole responsibility of the manufacturer:
Jack Sealey Ltd, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
Declaration of Conformity in accordance with the above Directive(s)�
Technical le compiled by: Jack Sealey Ltd
Being the responsible person appointed by the manufacturer.
Signed�������������������������������������������������������������������������������������������
Date�����������������������������������������������������������������������������������������������
Name���������������������������������������������������������������������������������������������
Position�����������������������������������������������������������������������������������������
Place: Bury St Edmunds
Jump Starter Power Pack 800A Peak Power – Lithium
SL67S v1
2014/30/EU EMC Directive
2011/65/EU RoHS Directive
References to harmonised standard(s)
EN 55032:2015�����������������������������������������������������������������������������
EN 61000-3-2:2014 ����������������������������������������������������������������������
EN 61000-3-3:2013 ����������������������������������������������������������������������
EN 55024:2010+A1:2015 �������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
25 July 2018
Steve Buckle�
Marketing Director�
XVII2813
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk