Sealey SL69S User manual

PLEASE SAVE THIS OWNER’S MANUAL AND READ BEFORE
USE. This manual will explain how to use the unit safely and
effectively. Please read and follow these instructions and
precautions carefully.
MODEL :
SL69S
Jump Starter
OWNER’S MANUAL
SL69S issue: 2 (10,11) 06/02/20

• 2 •
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .....................................................2
PERSONAL PRECAUTIONS ........................................................................3
PREPARING TO USE THE UNIT ..................................................................4
FOLLOW THESE STEPS WHEN CONNECTING TO A BATTERY .............4
FEATURES ....................................................................................................6
CHARGING THE JUMP STARTER ...............................................................6
OPERATING INSTRUCTIONS ......................................................................7
MAINTENANCE INSTRUCTIONS ................................................................9
STORAGE INSTRUCTIONS .........................................................................9
TROUBLESHOOTING ..................................................................................9
SPECIFICATIONS .......................................................................................10
SAFETY SYMBOLS
1. IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
WARNING – RISK OF EXPLOSIVE GASES.
WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS
DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES
DURING NORMAL OPERATION. IT IS IMPORTANT THAT YOU
FOLLOW THESE INSTRUCTIONS EACH TIME YOU USE THE UNIT.
To reduce the risk of battery explosion, follow these instructions
and those published by the battery manufacturer and the
manufacturer of any equipment you intend to use in the vicinity
of a battery. Review cautionary markings on these products and
on the engine.
Refer to
instructions
Wear safety
glasses
Warning!
Risk of
explosion
Warning!

• 3 •
WARNING! RISK OF ELECTRIC SHOCK OR FIRE.
1.1 Read the entire manual before using this product. Failure to do so
could result in serious injury or death.
1.2 Keep out of reach of children.
1.3 Do not put ngers or hands into any of the unit’s outlets.
1.4 Do not expose the unit to rain or snow.
1.5 Use only recommended attachments (SSL-JC jump cable). Use of an
attachment not recommended or sold by Sealey for the SL69S may
result in a risk of re, electric shock or injury to persons or damage to
property.
1.6 To reduce the risk of damage to the electric plug or cord, pull by the
adaptor rather than the cord when disconnecting the unit.
1.7 Do not operate the unit with damaged cables or clamps.
1.8 Do not operate the unit if it has received a sharp blow, been dropped
or otherwise damaged in any way; take it to a qualied service
person.
1.9 Do not disassemble the unit; take it to a qualied service person when
service or repair is required. Incorrect reassembly may result in a risk
of re or electric shock.
WARNING! RISK OF EXPLOSIVE GASES.
1.10 To reduce the risk of a battery explosion, follow these instructions and
those published by the battery manufacturer and the manufacturer of
any equipment you intend to use in the vicinity of the battery. Review
the cautionary markings on these products and on the engine.
1.11 Do not set the unit on ammable materials, such as carpeting,
upholstery, paper, cardboard, etc.
1.12 Never place the unit directly above battery being jumped.
1.13 Do not use the unit to jump start a vehicle while charging the internal
battery.
2. PERSONAL PRECAUTIONS
WARNING! RISK OF EXPLOSIVE GASES. A SPARK NEAR THE
BATTERY MAY CAUSE A BATTERY EXPLOSION. TO REDUCE THE
RISK OF A SPARK NEAR THE BATTERY:
2.1 NEVER smoke or allow a spark or ame in the vicinity of a battery or
engine.
2.2 Remove personal metal items such as rings, bracelets, necklaces and
watches when working with a lead-acid battery. A lead-acid battery
can produce a short-circuit current high enough to weld a ring to
metal, causing a severe burn.
2.3 Be extra cautious, to reduce the risk of dropping a metal tool onto the
battery. It might spark or short-circuit the battery or other electrical
part that may cause an explosion.
2.4 Do not permit the internal battery of the unit to freeze. Never charge a
frozen battery.

• 4 •
2.5 To prevent sparking, NEVER allow clamps to touch together or
contact the same piece of metal.
2.6 Consider having someone nearby to come to your aid when you work
near a lead-acid battery.
2.7 Wear complete eye and body protection, including safety goggles and
protective clothing. Avoid touching your eyes while working near the
battery.
2.8 Read the Material Safety Data Sheet available from www.sealey.
co.uk. In the event of an accident seek medical attention.
3. PREPARING TO USE THE UNIT
WARNING! RISK OF CONTACT WITH BATTERY ACID. BATTERY
ACID IS A HIGHLY CORROSIVE SULPHURIC ACID.
3.1 Make sure the area around the battery is well ventilated while the unit
is in use.
3.2 Clean the battery terminals before using the jump starter. During
cleaning, keep airborne corrosion from coming into contact with your
eyes, nose and mouth. Do not touch your eyes, nose or mouth.
3.3 Determine the voltage of the battery by referring to the vehicle
owner’s manual and make sure that the output voltage is 12V.
3.4 Make sure that the unit’s cable clamps make tight connections.
4. FOLLOW THESE STEPS WHEN CONNECTING TO A BATTERY
WARNING! A SPARK NEAR THE BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE
BATTERY:
4.1 Plug the clamps into the unit, and then attach the output cables to
the battery and chassis as indicated below. Never allow the output
clamps to touch each other.
4.2 Position the DC cables to reduce the risk of damage by the bonnet,
door and moving or hot engine parts. NOTE: If it is necessary to close
the hood during the jump starting process, ensure that the hood does
not touch the metal part of the battery clips or cut the insulation of the
cables.
4.3 Stay clear of fan blades, belts, pulleys and other parts that can cause
injury.
4.4 Check the polarity of the battery posts. The POSITIVE (POS, P, +)
battery post usually has a larger diameter than the NEGATIVE (NEG,
N, -) post.
4.5 Determine which post of the battery is grounded (connected) to the
chassis. If the negative post is grounded to the chassis (as in most
vehicles), see step 4.6. If the positive post is grounded to the chassis,
see step 4.7.
4.6 For a negative-grounded vehicle, connect the POSITIVE (RED) clamp
from the jump starter to the POSITIVE (POS, P, +) ungrounded post
of the battery. Connect the NEGATIVE (BLACK) clamp to the vehicle
chassis or engine block away from the battery. Do not connect the
clamp to the carburettor, fuel lines or sheet-metal body parts. Connect
to a heavy gauge metal part of the frame or engine block.

• 5 •
4.7 For a positive-grounded vehicle, connect the NEGATIVE (BLACK)
clamp from the jump starter to the NEGATIVE (NEG, N, -)
ungrounded post of the battery. Connect the POSITIVE (RED) clamp
to the vehicle chassis or engine block away from the battery. Do not
connect the clamp to the carburettor, fuel lines or sheet-metal body
parts. Connect to a heavy gauge metal part of the frame or engine
block.
4.8 When nished using the jump starter, remove the clamp from the
vehicle chassis and then remove the clamp from the battery terminal.
Disconnect the clamps from the unit.
5. FEATURES
1. LCD display
2. Display button
3. Smart cable green and red
LEDs
4. ON/OFF switch
5. Micro USB input port
for recharging
6. 3A input/output USB port
7. Quick Charge™
3.0 USB output port
8. 2.4A USB output port
9. SSL-JC smart cable
with battery clamps
10. Jump start output
socket
11. LED light
Not shown:
12. Micro USB-USB
charging cable
13. Carrying case

• 6 •
6. CHARGING THE JUMP STARTER
IMPORTANT! CHARGE IMMEDIATELY AFTER PURCHASE,
AFTER EACH USE AND EVERY 30 DAYS, OR WHEN THE
CHARGE LEVEL FALLS BELOW 85%, TO KEEP THE INTERNAL
BATTERY FULLY CHARGED AND PROLONG BATTERY LIFE.
6.1 CHECKING THE LEVEL OF THE INTERNAL BATTERY
1. Slide the ON/OFF switch to the ON position. The LCD display will
show the battery’s percentage of charge. A fully charged internal
battery will read 100%. Charge the internal battery if the display
shows it is under 85%.
2. To reduce the risk of electric shock, unplug the unit’s charging cable
from a USB or wall charger before attempting any maintenance or
cleaning. Simply turning off the controls will not reduce this risk.
3. When charging the internal battery, work in a well ventilated area and
do not restrict the ventilation in any way.
6.2 CHARGING THE INTERNAL BATTERY
NOTE: Use a 2A USB charger (sold separately), or a 2A USB
charging port to quickly recharge the jump starter. Using a charger
with less than 2A will increase charge time.
1. Plug the Micro USB end of the charging cable into the input port.
Next, plug the USB end of the charging cable into a charger’s USB
port.
2. Plug your charger into a live AC or DC power outlet.
3. The LCD display will light, the digit begins to ash and show “IN”,
indicating that charging has begun.
4. The jump starter will fully charge in 7-8 hours. When the unit is fully
charged, the display will show “100%”.
5. When the battery is fully charged, disconnect your charger from the
outlet, and then remove the charging cable from the charger and the
unit. Slide the ON/OFF switch to the OFF position, if you are not using
the unit immediately.
7. OPERATING INSTRUCTIONS
7.1 JUMP STARTING A VEHICLE ENGINE
NOTE: Use only model number SSL-JC jump cables.
IMPORTANT: DO NOT use the jump starter while charging its
internal battery.
IMPORTANT: Using the jump starter without a battery installed in the
vehicle will damage the vehicle’s electrical system.
NOTE: The internal battery must have a charge of at least 40% to
jump start a vehicle.
1. Turn the ignition OFF.
2. Plug the battery clamp cable into the jump starter’s output socket.
3. Lay the DC cables away from any fan blades, belts, pulleys and other
moving parts. Make sure all of the vehicle’s electrical devices are
turned off.
4. For a negative-grounded vehicle, connect the POSITIVE (RED) clamp
from the jump starter to the POSITIVE (POS, P, +) ungrounded post

• 7 •
of the battery. Connect the NEGATIVE (BLACK) clamp to the vehicle
chassis or engine block away from the battery. Do not connect the
clamp to the carburettor, fuel lines or sheet-metal body parts. Connect
to a heavy gauge metal part of the frame or engine block.
5. For a positive-grounded vehicle, connect the NEGATIVE (BLACK)
clamp from the jump starter to the NEGATIVE (NEG, N, -)
ungrounded post of the battery. Connect the POSITIVE (RED) clamp
to the vehicle chassis or engine block away from the battery. Do not
connect the clamp to the carburettor, fuel lines or sheet-metal body
parts. Connect to a heavy gauge metal part of the frame or engine
block.
6. Slide the ON/OFF switch to the ON position. The green LED on the
smart cable should light.
NOTE: If the vehicle battery is extremely discharged, the initial current
draw from the jump starter may activate short circuit protection in the
smart cable. When the condition is corrected, the smart cable will
automatically reset.
7. After a proper connection has been made, crank the engine. If the
engine does not start within 5-8 seconds, stop cranking and wait at
least 1 minute before attempting to start the vehicle again.
NOTE: If the car does not crank a second time, check the smart cable
to see if the green LED is lit. If an LED is ashing, refer to section 10,
Troubleshooting. When the condition is corrected, the smart cable will
automatically reset.
NOTE: Cold weather may affect the performance of the jump starter’s
lithium battery. If you hear only a click and the engine does not turn
over, try the following:
With the jump starter connected to the car battery and the green
LED illuminated on the smart cable, turn on all lights and electrical
accessories for one minute. This draws current from the jump starter
and warms the battery. Now try to crank the engine. If it does not turn
over, repeat the procedure. Extremely cold weather may require two or
three battery warmings before the engine will start.
IMPORTANT: DO NOT attempt to jump start your vehicle more
than three consecutive times. If the vehicle will not start after three
attempts, consult a service technician.
8. After the engine starts, unplug the battery clamps from the jump
starter socket and then disconnect the black clamp (-) and the red
clamp (+), in that order. Slide the ON/OFF switch to the OFF position.
9. Recharge the unit as soon as possible after each use.
7.2 CHARGING A MOBILE DEVICE, USING THE USB PORTS
The SL69S includes three USB ports. The standard one provides up
to 2.4A at 5V DC. The second port is a 3A input/output USB. The
third port is a Quick Charge 3.0™, which provides up to 5V at 3A, 9V
at 2A or 12V at 1.5A.
1. Consult your mobile device manufacturer for proper charging power
specications. Connect a mobile device cable to the appropriate USB
port.

• 8 •
2. Slide the ON/OFF switch to the ON position. Charging should begin
automatically. The display will show which port is in use.
3. Charging time will vary, based on the mobile device’s battery size and
the charging port used.
NOTE: Most devices will charge with any of the USB ports, but may
charge at a slower rate.
NOTE: The 3A USB port requires a specic charging cable
(not included).
4. When nished using the USB port, disconnect the charging cable
from your mobile device and then disconnect the charging cable from
the unit. Slide the ON/OFF switch to the OFF position.
5. Recharge the unit as soon as possible after each use.
NOTE: If no USB device is connected, power to the USB ports will
automatically shut off after 30 seconds.
7.3 USING THE LED LIGHT
1. Slide the ON/OFF switch to the ON position.
2. Hold down the display button for 3 seconds.
3. Once the LED light is on, press and release the display button to
cycle through the following modes:
• Steady glow
• Flash for an SOS signal
• Flash in strobe mode
4. When nished using the LED light, press and hold the display
button until the light turns off.
5. Slide the ON/OFF switch to the OFF position.
6. Recharge the unit as soon as possible after each use.
8. MAINTENANCE INSTRUCTIONS
1. After use and before performing maintenance, unplug and disconnect
the unit.
2. Use a dry cloth to wipe all battery corrosion and other dirt or oil from
the battery clamps, cords, and the outer case.
3. DO NOT open the unit, as there are no user-serviceable parts.
9. STORAGE INSTRUCTIONS
1. Charge battery to full capacity before storage.
2. Store this unit at temperatures between -4°F-+140°F (-20°C-+60°C).
3. Never completely discharge the battery.
4. Charge after each use.
5. Charge at least once every month, if not in frequent use, to prevent
over-discharge.

• 9 •
10. TROUBLESHOOTING
Jump Starter
PROBLEM SOLUTION
The jump starter’s display will
not turn on.
Make sure the unit is charged.
Connect to a power source, to reset.
Make sure the ON/OFF switch is set to
the ON position.
The thermometer symbol
is ashing.
The unit is too hot or cold. The thermometer
symbol will disappear when the condition
is removed.
The jump starter will not
recharge.
Make sure the power source is live.
The jump starter turns on, but
won’t jump start my vehicle.
Check connections
Verify the charge level of the jump starter is
at least 40%.
Do not attempt to jump start your vehicle
more than three consecutive times. If
the vehicle still does not start, consult a
qualied service technician.
When cable is connected only
to the battery: Solid Red LED,
(Green LED off); beeps once
per second
The vehicle battery voltage is lower than
10.5V. User can connect to jump starter
and turn key to jump start the vehicle.
When cable is correctly
connected to both battery
and jump starter: Green LED
blinking; Red LED off; no
beep.
”Fake” high battery voltage is detected,
but reverse charging protection did not
activate. User can turn key to jump the
vehicle.
Smart Cable LED and Alarm Behavior
BEHAVIOUR REASON
Green LED blinking; Red LED
off; no beep.
Cable is connected to battery only. Cable
is connected to jump starter only.
Green LED solid; Red LED off;
no beep.
Cable is connected correctly to both
battery and jump starter.
Solid Red LED, Green LED off;
beeps once per second
Low voltage protection.
Solid Red LED, Green LED off;
beeps twice per second
Reverse polarity protection.
Alternating Red and Green
ashing LEDs; no beep
Reverse charging protection.
Solid Red LED, Green LED off;
rapid beeping
Short circuit protection.

• 10 •
BEHAVIOUR REASON
Solid Red and Green LEDs;
no beep
Auto shut-off due to inactivity. Disconnect
and reconnect clamps to the vehicle
battery.
Solid Red and Green LEDs;
beeps once per second.
Temperature protection
NOTE: When the condition is corrected, the smart cable will automatically
reset.
11. SPECIFICATIONS
Auxiliary output:
..............USB (x2) - 5V/2.4A, 5V/Quickcharge 3.0 + Type ‘C’ 5V/3A
Cable & clamp length: ...........................................................440mm
Capacity: ......................................... 15Ah @ 3.2V, 3.75Ah @ 12.8V
Max. current: .......................................................................... 1000A
Max. starting capacity: ........................................6L Petrol/3L Diesel
Size (W x D x H):...................................................95 x 40 x 185mm

• 11 •
Sealey Group, Kempson Way, Suffolk
Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500 01284 703534
[e-mail] www.sealey.
co.uk
WEEE REGULATIONS
Dispose of this product at the end of its working life in
compliance with the EU Directive on Waste Electrical
and Electronic Equipment (WEEE). When the product
is no longer required, it must be disposed of in an
environmentally protective way. Contact your local
solid waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of
them as waste. All tools, accessories and packaging
should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the
environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids
(if applicable) into approved containers and dispose of
the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such
we reserve the right to alter data, specifications and component
parts without prior notice.
Important: No Liability is accepted for incorrect use of this
product.
Warranty: Guarantee is 2 years from purchase date for the unit,
1 year for the battery. Proof of purchase is required for any claim.
Parts support is available for this product. To obtain parts,
please log on to
www.sealey.co.uk, email [e-mail] or telephone
01284 757500

• 12 •
EC DECLARATION
OF CONFORMITY
Description and Function:������������������������������������������������������������������������������������������������������������������������������������������������������������������������
Model/Type: ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
Manufacturing Date/Serial Number where applicable: ����������������������������������������������������������������������������������������������������������������������������
This declaration of conformity is issued under the sole responsibility of the manufacturer:
Jack Sealey Ltd, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
Declaration of Conformity in accordance with the above Directive(s)�
Technical le compiled by: Jack Sealey Ltd
Being the responsible person appointed by the manufacturer.
Signed�������������������������������������������������������������������������������������������
Date�����������������������������������������������������������������������������������������������
Name���������������������������������������������������������������������������������������������
Position�����������������������������������������������������������������������������������������
Place: Bury St Edmunds
Lithium Jump Starter Power Pack
SL69S v1
2014/30/EU EMC Directive
2011/65/EU RoHS Directive
References to harmonised standard(s)
EN 55032:2015�����������������������������������������������������������������������������
EN 55035:2017�����������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
25 July 2018
Steve Buckle�
Marketing Director�
XVII2813
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk