Sealey APMSHFP Series User manual

10PC GARAGE STORAGE SYSTEM
MODEL NO: APMSHFP SERIES
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this storage
system.
9Locate in a suitable work area.
9Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use storage on level and solid ground, preferably concrete.
9Keep the storage system clean and tidy in accordance with good workshop practice.
9Keep children and unauthorised persons away from the work area.
8DO NOT use the storage system for any purpose other than that for which it is designed.
8DO NOT use the storage system outdoors.
8DO NOT place the storage system in a damp or wet location or an area where there is condensation.
8DO NOT clean the storage system with any solvents which may damage the surfaces or the protective coating.
8888 DO NOT move the storage system when there are items placed inside.
8888 DO NOT step on the shelves.
8888 DO NOT8overload the storage system.
2. INTRODUCTION
Can be free standing or xed to the wall. All ten units supplied on a single pallet. Hinged at pack design makes this storage system easy and
quick to assemble. Base units tted with stylish black MDF worktops and adjustable feet. Fitted with ball bearing drawer runners and magnetic
door latches. Pegboard design backing panels for additional storage. Extra units available to extend the storage system if required. Some simple
assembly required.
3. SPECIFICATION
Model no: .........................................................APMS10HFP
Garage storage system 10pc
Overall size: ........................................3100 x 460 x 2080mm
Inner drawer dimensions:........................670 x 398 x 122mm
Model no: ...........................................................APMS2HFP
Modular wall and base cabinet
Model no: ........................................................ APMS2HFPD
Modular wall and base cabinet with drawer
Model no: ........................................................ APMS2HFPS
Modular stacking cabinet
APMSHFP series | Issue 1 21/10/19
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear
protective
gloves

4. ASSEMBLY
Original Language Version
© Jack Sealey Limited
1 DOOR WALL CABINET
STEP 1: Carefully separate the front and back panels, allowing the side panels to unfold completely.
STEP 2: attach the top panel using 8x M6x16mm screws. STEP 3: Turn the cabinet over. Attach the bottom panel using
11x M6x16mm screws.
STEP 4: Insert 4 shelf supports inside the cabinet at the desired height. Place the shelf on the shelf supports.
APMSHFP series | Issue 1 21/10/19
top panel
shelf support x4
shelf

Original Language Version
© Jack Sealey Limited
STEP 2: Attach the bottom panel using 11x M6x16mm screws.
STEP 3: Screw the 4 adjustable feet into
the cabinet bottom.
STEP 4: Attach the worktop to the cabinet using 4x M6x16mm screws.
STEP 5: Insert four shelf supports inside the cabinet at the desired height. Place the shelf on the shelf supports.
NOTE: The cabinet will only lock when the shelf is placed in the centre position.
APMSHFP series | Issue 1 21/10/19
2 DOOR BASE CABINET WITH WORK TOP
STEP 1: Carefully separate the front and back panels, allowing the side panels to unfold completely.
M6x16mm screws x4
shelf support x4

Original Language Version
© Jack Sealey Limited
STEP 2 TOP CABINET: Attach the top panel using
8x M6x16mm hex socket head screws.
STEP 4 TOP CABINET: Turn the cabinet over. Attach the bottom panel using 7x M6x16mm screws.
2 DOOR STACKING CABINET
STEP 1: Carefully separate the front and back panels, allowing the side panels to unfold completely.
STEP 3 BOTTOM CABINET: Place the top panel on the bottom cabinet.
Do not attach yet.
APMSHFP series | Issue 1 21/10/19
M6x16mm
screws x8
M6x16mm
screws x7
top panel
top
cabinet
top
cabinet
top
cabinet
bottom
cabinet
top panel

STEP 5 BOTTOM CABINET: Turn the cabinet over.
Attach the bottom panel using 11x M6x16mm screws.
STEP 6 BOTTOM CABINET: Fit adjustable feet.
STEP 7: Place top cabinet onto bottom cabinet.
STEP 9: Insert 4x shelf supports inside the cabinet at the desired height. Place shelf on shelf supports. NOTE: the cabinet will only lock when
the shelf is placed in the centre position.
STEP 8: Connect top and bottom cabinets
using M6x35mm hex ange bolts.
Repeat for the other stackable combination.
M6X35 ange bolt
X4
Original Language Version
© Jack Sealey Limited APMSHFP series | Issue 1 21/10/19
bottom
cabinet
bottom
cabinet
bottom
cabinet
top
cabinet
M6x16mm
screws
shelf
shelf support

1 DRAWER/2 DOOR CABINET WITH WORK TOP:
RAIL TYPES:
STEP 1: Fit feet.
STEP 2: Attach 2x cabinet rails to the back of the base
cabinet using 3x M6x16mm screws per rail.
STEP 3: Slide 2x peg board rails fully onto the cabinet posts.
Place one pegboard on the front, making sure the grommet hole is on
the bottom. Attach using 2x M6x16mm screws per rail.
TO REMOVE DRAWERS
Pull drawer out so it’s almost fully extended.
Push up right hand black release lever, while
pulling down left hand black release lever,
pull the drawer out until it is released from
the slides.
TO REPLACE DRAWERS
Extend the drawer slides. Insert the brackets
on each side of the drawer into the slots in
the cabinet slides, being careful to ensure
that they are properly positioned. Once
properly inserted, completely close
The drawer to set the slides in their proper
positions.
APMSHFP series | Issue 1 21/10/19
Original Language Version
© Jack Sealey Limited
cabinet
rail x8
adjustable feet
pegboard x1
pegboard rail x2
M6x16mm
screw x4
pegboard rail
x4
pegboard x4

STEP 4: Slide 2 cabinet rails onto the pegboard rails. Ensure
there is enough room at the top for the wall cabinet. Attach 2
cabinet rails using 2x M6x16mm screws per rail. Attach second
pegboard, ensure grommet hole is at the top.
2 DOOR CABINET WITH WORKTOP:
STEP 7: Slide 2 pegboard rails fully onto the cabinet rails. Place
one pegboard on the front, making sure the grommet hole is on
the bottom. Attach using 2x M6x16 screws per rail.
STEP 5: Screw two M6x16mm screws, into
the back of the top cabinet, leaving a 0.8cm
gap. Do not tighten bolts fully. Hang the wall
cabinet on the top of the posts, then fully
tighten the screws. Attach the bottom of the
wall cabinet to the posts using another 2x
M6x16mm screws.
STEP 8: Slide 2 cabinet rails onto the
pegboard rails. Make sure to leave
enough room at the top for the wall
cabinet. Place one pegboard on the
front, making sure the grommet hole
is on the top. Attach using 2x
M6x16mm screws per rail.
STEP 9: Screw 2x M6 x 16mm into the back of the
top cabinet, leaving a 0.8cm. Do not tighten bolts
fully. Hang the wall cabinet on the top of the rails,
then fully tighten the screws. Attach the bottom of
the wall cabinet to the rails using another two M6x
16mm screws.
APMSHFP series | Issue 1 21/10/19
Original Language Version
© Jack Sealey Limited
pegboard
cabinet rail
M6x16mm
screw x4
M6x16mm
screw x6 M6x16mm
screw x4
M6x16mm
screw x4
M6x16mm
screw x2
pegboard rail x2
cabinet
rail x2
pegboard
x1
M6x16mm
screw x2
STEP 6: Attach 2x
cabinet rails to the
back of the base
cabinet using 3x
M6x16mm screws
per rail.

STEP 10: Push the two base cabinet/top cabinet
combinations together. Insert a M6x16mm screw
through the two interior end cover holes and fasten
with a M6 flange nut.
STEP 11: Push a stackable cabinet combination towards either side of
the base cabinet/top cabinet combination. Insert a M6x16mm screw
through the two interior end cover holes and secure with a M6 flange nut.
APMSHFP series | Issue 1 21/10/19
Original Language Version
© Jack Sealey Limited
M6x16mm
screw x2
M6x16mm
screw x2
M6
flange
nut

STEP 12: Attach the modular storage kit to the wall using twelve M6x65mm tapping screws and washers insert through wall studs. Insert the 6
end cups on the side panels of the cabinets.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
APMSHFP series | Issue 1 21/10/19
Original Language Version
© Jack Sealey Limited
washer
x12
M6x65mm
self tapping
screw
end
cap
wall