.qMPO_RTANT=We adv s,:;yol=to assemble the t.mt once before going carnpin:!;Ito be_;omefamiliar with the
:_:,.,.,assembly of the re ii.. Forthi_ model, it is "_commended two people be inTo|ved in the set up.
NOTE: Please look _Lt_h,.;repl_Lcementpads di-:_ram to see how your frame is assembled.
, To prolong the life, pf'the t._r_ floor, select a low.I, clean area for the camps/to,
- To prevent darnag_ 1_:_the i_ippP.r, unzip the do,:.f, ;, prior to tent set-up, to allow air to enter the tent.
* To improve the we= tiler r_i_istance of your tent, i; is advisable to use seam seater to, _=oat all expas,_d seams.
You should app])/c _y to ti_e underside of the ';_/and inside _earnG of the tent. If arcpiled to the outslde af seams,
discoloration of yo= ir tent #_ay,oocur. Seam s_:_d_ris available at the c_mping secti,',,n of your local Se_.rs store.
•ForyourconvenFer
Simply unzip the sl
betweenthebot_o_
=_ and:,_llnproved tent funct!,._ _altty, we have developed a s_'.lf-colltained storm flap _acket,
'rn flai_,'-"covering the wind_ _ts and door_ and drop into the po,I;ket that has been formed
of the'..,_to_mflap and the _a,.sh window.
STEP 3; Insert the kn_)bonthe undersideof the centerhub
into the relnf,;rced h,_leat the center roofof the
tent. Thefib _rglasssections shouldbe extended
to hold the c:;;nter
roof of the te:nt
in place. \
_' of the tent. The flat, smoothside of _
!! the centerhub, l:ould be UR Once _i
e.berg . s:,ions , so od/lA!i
_': into the sleew,s, t 'he _b;i.l°gT_SS _ /-/#////
_i sections shoulld ) _;ins_!rl:ed_////_/
soa od
/IF ,/Fo '
ii
Locate the cent_r =_pld_',rhub(Key13).Go '_cthe
center roof of th._._ent$_ndinsertone of e_.'h of the
eight fiberglass=_ctlon_:_,ate.achedto the _ _ter
hub through the _',.ntsh;_;vesat the very c,_,_arroof
STEP
STEPS:
STEP 6:
Locatethe t;h_eefiberglass ridge poles(KeyA).
Extend each pole by insertingthe fiberglass
sections intothe metal ferrules. Eachridgepole
will haveaplastic elbowjointoneach end. Slide
one ridge pc,,:_through eachof thepole sleeves
located on tlh,_ends of thetent siderooms.
Attach small hooks at each roof cornerto the
holes in eachof the __---_
plastic elbov' _..-_"_--
joints. Flexlrl;fti_e _
fiberglass wil be j'_..._-'_--
necessary. ._- x_.
Unfold the fl'_ and place overthetent.
Locate the s"<steel side uprights (KeyB), Join the
upper end e'. each upright, which will have a metal
,__ ring attached for the fly attachment nearthe end,
I_ tothe plastk, elbow jointsoneach ofthe fiber-
IIJ glass r_dgeI_oles. With oneperson on either side
of the tent, i_Jsethe side rooms by raising the side
ill _ uprightpole_ and adiusting untilthe wailsare taut.
111_ The ep_.nends of tFe steel poles should rest upon
Ill _ the ground. Repeat this step with the remaining
side rooms ,_.t_dsteel side upright poles.
