Seaside 9357 User manual

1
Address: No.23-7.Yaobei Road,Dalian,China
Website: www.seaside.net.cn
GARAGE DOOR operator
Models 9357
For Residential Use Only
Before installation, write down the serial number and purchase date:
(The model number is labeled on the plastic cover with light socket of your operator).
Serial # _ _ _ _ _ _ _ _ _
Purchase Date _ _- _ _- _ _ _ Version No.:MEN-005-B
Owner’s Manual

2
Before installation, please read this manual and instructions carefully!
The Photo eye system must be installed.
Routine maintenance of the operator according to this manual to
ensure safe operation.
Please keep the manual in your sight near the garage door.
TABLE OF CONTENTS
Introduction…......................................................3-4
Operator contents and tool.........................……5-9
Installation steps........................………………..9-20
1. Adjust the chain or belt.........................................9
2. Connect the rail to the operator..........................10
3. Install The Header Bracket.................................11
4. Connect the Rail to the Header Bracket.............12
5. Attach the garage door operator to the
ceiling................................................................13-15
6. Install the door bracket.......................................15
7. Attach the door arm......................................16-17
8. Install light bulb.............................................17-18
9. Install the Emergency Release Cord and
Knob……………........…………………………….18-19
10. Install The Wall Control...............................19-20
11. Connect the wall control to the garage door
operator……………………………………….……….21
12. Attach the warning labels.................................21
13. Install The Photo Eye System.....................22-24
14. Connect the operator to power....................24-26
15. Aligning and adjusting the Photo Eye
System...............................................................26-27
Test and Adjustments.....................………………27
1.SYSTEM SETUP............................................28-29
2.TEST THE REVERSING SAFETY SYSTEM..29-30
3.FORCE SENSITIVITY ADJUSTMENT...........30-32
4.TEST THE PHOTO EYE SAFETY
SYSTEM…………………………………………..33-34
5.WALL CONTROL................................................35
6.PROGRAM THE REMOTE CONTROL...............36
7.DELETE THE MEMORY......................................37
8.USE EMERGENCY RELEASE TO OPEN
GARAGE DOOR MANUALY..........................37-38
Maintenance schedule…....……………………….38
Operator Parts…...........………………………..39-40
Troubleshooting…......................……………..41-42
Limited Warranty..................................................43

3
WARNING
INTRODUCTION
Safety Symbols
This garage door operator has been tested and manufactured to provide safe
service . Please install, handle, maintain, and check in strict compliance with the
instructions and warnings used in this owner’s manual.
The following Safety Symbols used in this manual will warn you the possibility of
serious injury or death if you do not operate in accordance with the warnings
attached. Read them carefully.
Mechanical Electrical
Before installation
1 Lift the door by hand, the door should stay rest when halfway up.
2 If the door does not open and close smoothly and with little resistance, contact a
qualified garage door technician.
3 The garage door should open all the way up, or close all the way down. Otherwise,
contact a qualified garage door technician.
CAUTION
WARNING

4
This garage door operator is designed to operate only at 120V, 60 Hz to avoid
malfunction and damage.
CAUTION
IMPORTANT INSTALLATION INSTRUCTIONS
To prevent any possible SERIOUS INJURY or DEATH:
1. Read and follow all installation instructions.
2. Always call a professional qualified door technician to make repairs to garage
door cables, spring assemblies, and other hardware before installing the
operator. This operator only works with a properly balanced garage door.
3. Never try to adjust garage doors, springs, cables, pulleys, rollers, brackets or
other door hardware, unless you are qualified to do so.
4. Make sure you have another access door besides garage door. If not, you must
install an emergency release kit that can be operated outside.
5. Remove all ropes and remove or make inoperative all locks connected to the
garage door before installing the operator.
6. Do not connect the operator to power source until instructed to do so.
7. Use this operator only with Sectional Door.
8. Contact the garage door manufacturer to see if additional reinforcement is
needed to support the door before installation of the operator.
9. If possible, install the operator 7 feet(2.1m) or more above the floor and the
center of the door. Mount the emergency release knob 6 feet above the floor
and avoid contact with any moving object.
10.Install the wall control:(a)within sight of the door,(b)at a minimum height of 5
feet(1.5m) above the floor that small children cannot reach it.(c)away from all
moving parts of the door.
11.Attach the warning label next to the wall control in a prominent location. Attach
the hanging warning label to the emergency release knob.
12.After installing the operator, the door must reverse when it contacts a 3.8cm(or
a 2x4 laid flat)on the floor.
13.Must disconnect operator from power source BEFORE performing any service
or maintenance.
WARNING

5
A、Header bracket
B、Pulley assembly
C、Door bracket
D、Curved door arm
E、Straight door arm
F、Trolley assembly
G、Emergency release rope and knob
H、One-Piece Rail
I、Hanging bracket
J、Garage door operator
K、“U” rail clips（2）
L、Photoelectric sensors
M、Chain/Belt
N、Sprocket and sprocket holder assembly
O、Wall Control
P、Safety labels and literature
Operator contents and tools:
A
C
E
D
H
I
J
O
P
L
G

6
The tools illustrated below may be used during installation
and adjustment of your operator:
For future reference, the following parts should be
pre-installed in the rail.
A、Rail
B、Pulley assembly
N、Sprocket and
sprocket holder
assembly

7
Belt
Belt
Belt Connector
Chain Connector
Chain
Chain
Locking Holes
F、Trolley Assembly
1
2
3
4
5

8
Hardware
Straight door arm
“U” rail clip
Header bracket
Door bracket
Hanging bracket
H1 Shouldered
shaft, long Φ8×80 (1)
H2 Shouldered
shaft, short Φ8×30 (2)
H3 Hex Nut M8(6)
H4 Hex Bolt M8×20(6)
H5 Cotter Pin Φ2×25(3)
H6 Screw M5×20(2)
H7 Lag Screw M8×50 (6)
Concrete Anchors (2)
Screw M4×30 (2)
H8 Self-drilling Screw M6×25 (4)
Warning labels and literature
Curved door arm

9
INCLUDED ACCESSORIES
INSTALLATION STEPS
Do not run the garage door operator until instructed.
1、Adjust the chain or belt
1.1 To increase the tension and tighten the chain, turn the tension nut
clockwise with adjustable wrench until the nut is spaced properly from
the rail end-plate.
1.2 Once the nut is spaced correctly, any additional tightening will over
tighten the chain and may cause damage to the system.
1.3 To loose the tension, turn nut counter clockwise.
To prevent INJURY from pinching, keep hands and fingers away from the
joints while assembling the rail
CAUTION
Wall Control Panel
W221
Remote Control(2)
T041-315
Photo Eye Sensors
2.5cm
Rail end plate

10
2、Connect the rail to the operator
2.1 Position operator as showed below. Rest operator head on cardboard or
protective surface on floor so operator does not get scratched. Chassis side of
operator facing up.
2.2 Position rail onto operator chassis by lining up rail sprocket, Make sure shaft
insert into rail sprocket. Press rail down firmly onto shaft and operator chassis.
DO NOT HAMMER.
2.3 Remove the four bolts(H4) from the chassis of the garage door operator.
2.4 Position 2 “U” rail clips over rail and onto chassis. Insert 4 hex bolts (H4) through
rail clips holes and into chassis holes. and tighten hex bolts firmly to hold rail to
the garage door operator head.
To avoid SERIOUS damage to garage door operator, use ONLY those bolts
mounted in top of the operator.
CAUTION
2.3
2.4
H4
2.2
2.1

11
3、Install The Header Bracket
3.1 Close the door and mark the center point of the door as vertical guide line.
3.2 Locate the horizontal guide line for the header bracket and mark it. It must be at
least 2” (50mm) from the doors highest position.
3.3 Position the header bracket in the center of the vertical guideline and draw the
horizontal set of bracket holes.
3.4 Drill two 3/16“ holes at the marked mounting points on the header.
If installing into masonry, use concrete anchors (not provided).
3.5 Fasten the bracket securely to the header with the provided materials.
To reduce any possible SERIOUS INJURY or DEATH:
· Header bracket MUST be fastened to structural support on header Wall or
ceiling, otherwise the reversing safety system may not work.
· Do not install header bracket over drywall.
· The operator only works with a properly balanced garage door.
WARNING
H7 Lag Screw M8×50 (2)

12
4、Connect the Rail to the Header Bracket
Mount the rail to the header bracket by inserting the Shouldered shaft (H1) through
the holes in the header bracket and rail. Secure with the cotter pin(H5).
HARDWARE
H1 Shouldered shaft, long
Φ8×80 (1)
H5 Cotter pin Φ2×25(1)
Header wall
Optional ceiling
mount for
Header bracket
Unfinished
ceiling
Structural support
2x4

13
5、Attach the garage door operator to the ceiling
5.1 Elevate the operator onto a ladder. You will need help if the ladder is not tall
enough.
5.2 Open the door all the way, leave the operator on the top section.
HARDWARE
H4 Hex Bolt M8×20(4)
H3 Hex Nut M8(4)
H7 Lag Screw M8×50 (2)
To reduce possible SERIOUS INJURY, the garage door operator must be
properly secured to structural support of the garage.
H5
H1
WARNING

14
5.3 On finished ceilings, use the lag
screws (H7) to fasten a hanging
bracket (not provided) to the structural
supports before installing the garage
door operator.
5.4 The garage door operator must be
aligned with the hanging bracket. The
distance from each side of the garage
door operator to the structural
supports must be equal.
5.5 Cut the hanging brackets to
measured lengths.
5.6 Fasten the end of each hanging
bracket to the bracket on the
ceiling.
5.7 Fasten the hanging bracket on the chassis of garage door operator with
bolts (H4),and nuts (H3).
H7

15
6、Install the door bracket
NOTE: Please contact your garage door manufacturer if your garage door
needs reinforcement kit. Many door reinforcement kits provide for direct attachment
of the clevis pin and door arm. In this case you will not need the door bracket;
proceed to the next step.
6.1 Keep the door in the closed position.
6.2 Align the door bracket to the center line of the top section 2” to 4” below the top
edge of the door. Mark mounting points.
6.3 Drill 3/16" fastening holes, Secure the door bracket by using the four
self-threading screws (H8). Pay attention on your doors construction:
5.8 Open and close the door
manually. If the door hits the rail, lift
the header bracket.
H3
H4
H8
H8 Self-Threading Screw M6×25(4)

16
7、Attach the door arm
H2 Shouldered shaft
Φ8×30 (2)
H5 Cotter pin
Φ2×25(2)
H3 Hex Nut
M8(2)
H4 Hex Bolt
M8×20(2)
7.2 Pull the emergency release to move the trolley to the locking holes. Connect the
straight door arm to the trolley by using the shouldered shaft (H2).Attach the
shouldered shaft with the cotter pin.
7.1 Close the door. Connect the curved door arm to the door bracket by using the
shouldered shaft (H2).Attach the shouldered shaft with the cotter pin(H5).
H2
H5
H2
H5

17
NOTE: If the door arm is hanging down too far, please cut the extra part from the end.
8、Install light bulb
To avoid possible overheating of the end panel or light socket:
· Use ONLY A19 incandescent or compact fluorescent light bulbs.
· DO NOT use incandescent bulbs larger than 100W.
· DO NOT use compact fluorescent lamp(CFL) larger than 26W (100W) equivalent.
· DO NOT use halogen bulbs.
· DO NOT use short neck or specialty light bulbs.
7.5 After door bracket, door arms and trolley securely fastened, Pull the
emergency release towards the chain/belt connector . Once they are
connected, you will hear a click.
7.3 Line up the straight arm and curved arm. And fasten them using the bolts
(H4), nuts (H3) inserted in the 2 holes as far apart as possible.
7.4 If the curved arm and straight arm’s holes do not exactly match, pull the
emergency release to move the trolley a little bit. The holes should be aligned.
WARNING
H3
H4

18
A
8.1 To remove the two screws in both light lenses,then take both light lens out..
8.2 Insert two A19 incandescent or compact fluorescent light bulb (100 watt
maximum), or compact fluorescent (26W) into both light sockets.
8.3 Line up the lens taps with slots in operator, fasten it with the two screws.
9、Install the Emergency Release Cord and Knob
NOTE: Ensure that the emergency release cord and knob are above the top of
all moving objects to avoid entanglement.
9.1 Insert one end of the emergency release cord through the hole in the trolley
and tie a knot securely.
9.2 Insert the other end of the emergency release cord through the knob. Tie a
knot securely. Make sure the knob is 6 feet (1.83 m) above the floor. Cut off
the remaining cord.
9.3 Make sure the knots are tied securely. If cord knots become untied or loosen,
you could fall.
To avoid possible SERIOUS INJURY or DEATH from a falling garage door:
If possible, use emergency release to disconnect trolley ONLY when
garage door is closed. Deficient springs or unbalanced door could cause an
open door falling accident.
DO NOT use handle to drag door open or close.
Always make sure the doorway is clear of persons and obstructions.
WARNING
OR

19
10、Install the wall control
HARDWARE
Installation and wiring must comply with local building and electrical rules and
laws.
To avoid any possible SERIOUS INJURY or DEATH :
·DO NOT connect the power source at this time.
·The wall control should be at a minimum height of 5 feet (1.5 m) from the
floor out of reach of children. The wall control must be installed inside the
garage within sight of the garage door.
·Do not let children play with wall control buttons or remote controls.
·Open or close door ONLY when the doorway is clear, and the garage door
and operator are properly installed and maintained. The wall control must be
away from all moving parts of door.
·While using the wall control or remote controls, the user must have clear
vision of the garage door until the door is fully closed.
Emergency release cord and knob
WARNING
Concrete Anchors (2)
Screw M4×30 (2)

20
10.1 Strip back 10 mm of
insulation and separate the wires.
10.2 Open the back cover of the wall
control.
10.3 If the wires are not connected,
Connect the white wire to the #3
screw ,connect the red \white
wire to the #4 screw.
10.4 Mark the location of the 2 holes
of back cover of wall control and
drill a 6 mm hole.
10.6 Snap the wall control
onto the back cover.
5/13” (10mm)
10.5 Insert and tighten screws to
secure the back cover of the
wall control to wall.