B&D Controll-A-Door Secure SDO-6 User manual

These instructions are intended for professional garage door
installers.All references are taken from inside looking out.
Smart Phone Control Kit
Doc # 161056_01
Part # 86958
Released 19/11/19
Smart Hub Installation Instructions
CAD Secure (SDO-6) & PanelMax (SDO-8)
NETWORK SMART HUB KIT - ORDER NO. 86957
ITEM DESCRIPTION QTY
1 WIRELESS HUB100 WT B&D 1
2 POWER SUPPLY AU 240V 1
3 WALL BRACKET HUB100 1
4 PLASTIC WALL PLUG 6.9 X 25 2
5 SELF TAPPING SCREW 6 X 25 2
6NETWORK TRANSCEIVER MODULE 1
7 HARNESS 4 CORE 275 ASSY 1
Garage Door Openers
Important Safety Instructions
WARNING! • DO NOT attempt to disassemble, repair or modify the product. This will
invalidate the warranty.
• DO NOT install product on openers that control J-Type or Single Piece Doors.
• Do not allow children to play with the Smart Hub or your smart phone if the
B&D phone app has been installed.
ELECTROCUTION! • Keep the device away from water and other liquids. In the event that water
or other liquids enter the device, power off he product immediately and
clean the device.
• To reduce the risk of re or electric shock, do not expose this device to rain or
moisture.The device should not be exposed to dripping or splashing.
• DO NOT remove the cover as there are no user-serviceable parts inside.
CAUTION:
Fall from ladder • Ensure ladder is the correct type for job.
• Ensure ladder is on at ground.
• Ensure user has 3 points of contact while on ladder.
Burns • DO NOT handle damaged or leaking batteries
This device allows for operation of the door when not in line-of-sight of the door and
opener.
The door may operate unexpectedly, therefore do not allow anything to stay in or near the
path of the door. When the door is not operating automatically, watch the door when it is
moving and keep people away until the door is completely opened or closed. Contact with
the moving door can cause serious personal injury or damage to property.
It is our strong recommendation that your opener be tted with SAFETY BEAMS.Safety
Beams detect any obstructions in the doors path and override automatic operation if
one presents. These must be installed as in accordance with AS/NZS 60335-2-95:2012.
This is in addition to regular professional servicing, and monthly obstruction tests as detailed
in your opener’s Home Owners Manual.
This device must be connected to power at all times.
DO NOT disconnect power after setup.

b&d group ofce locations
Head Ofce 6-8 Fiveways Blvd, Keysborough 3173 Phone [phone]
New South Wales 34 Marigold St, Revesby 2212 Phone [phone]
Queensland 17 Oasis Court, Clontarf 4019 Phone [phone]
Victoria 147-153 Canterbury Rd, Kilsyth 3137 Phone [phone]
South Australia 23 Frederick Rd, Royal Park 5014 Phone [phone]
Western Australia 96 Mulgul Rd, Malaga 6090 Phone [phone]
International/Export 34 Marigold St, Revesby 2212 Phone [phone]
New Zealand 46 Braeburn Dr, hornby, Chch 8082 Phone [phone]
www.bnd.com.au
Prefixed trademarks are the property of B&D Australia Pty Ltd. B&D Doors & Openers
is a division of B&D Australia Pty Ltd.ABN 25 010 473 971. © 2016 B&D Australia Pty Ltd.
2
Smart Phone Control Kit - Installation instructions
your representative is
Warranty
Smart Hub Set Up
Mounting the Hub
a. Determine whether you are going to wall mount the hub.
i. If hub is to be placed on bench, simply connect to power supply
2, turn on and proceed to installing the Transceiver.
ii. If hub is to be wall mounted follow steps below.
b. To wall mount - Use wall bracket 3as template to mark where to drill
holes. Pre-drill holes.
i. For plaster walls - insert (2) two Plastic wall plugs 4into holes,
place wall bracket over holes and afx with (2) two self tapping
screws 5.
ii. For brick walls - place wall bracket 3over holes and afx with (2)
two self tapping screws 5.
c. Slide the hub over the bracket.
d. Connect the power supply 2and turn on.
1
3
5
6
6
SDO-8
ACC
This device must be connected to power at all times.
DO NOT disconnect power after setup.
Mounting the Transceiver to the Opener
a. Disconnect the power supply to the opener.
b. Remove the screw holding cover from the
opener.
c. Connect the 4 pin harness 7to ACC on the
control board then connect to the wireless
basestation module 6.
d. Place the module into the pocket as shown
and ret the cover.
e. Download the B&D App and follow the
instructions in the App to setup new smart hub.
f. Use a programmed remote and run the door
through a few cycles which will update the
unit with the details of the transceiver module.
SDO-6
Refer to our websites for full warranty details;
www.bnd.com.au
WARRANTY
ACCESSORIES 1 year
If you are a consumer under the Australian Consumer Law, our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty certicate and other statements contained in this document or other ATA documents given to you do not exclude, restrict or modify the application of
all or any of the provisions of the Australian Consumer Law.
Subject to your non-excludable rights under the Australian Consumer Law, ATA expressly excludes any liability for consequential loss, incidental or indirect damages
(including but not limited to damages for loss of business prots, business interruption and loss of business information) due to a defect of the Product. In particular,
any loss or damage caused to other equipment or accessories used with the product or any loss resulting from a delay in repair is excluded to the extent permitted
by law.
ACC