Sebago Furniture Rockland Bed User manual

Rockland Bed Assembly Instructions, Rev 1. 121102
207 - 591 – 4215 Sebago Furniture www.sebagofurniture.com
Dear Customer:
Thank you for purchasing a Rockland Bed from Sebago Furniture. The following
instructions will enable you to assemble your bed with a few simple tools.
PLEASE READ ALL OF THE INSTRUCTIONS BEFORE PROCEEDING TO
ASSEMBLE YOUR BED. You should have another person available to help hold
and align the pieces during the assembly process. Please do not hesitate to call
if you have questions or difficulty assembling your new bed.
Tools Required:
1. Medium size screwdriver
2. 9/16” Socket Wrench
3. 9/16” open end wrench (King Bed only)
RAIL ATTACHMENT
1. Locate the rails, header and
footer.
2. Place Header against wall where
the bed is to be located.
3. Position the Footer in front of the
header at its approximate final
location.
4. Place a Rail on either side
between the Footer and the
Header
All manuals and user guides at all-guides.com
all-guides.com

Rockland Bed Assembly Instructions, Rev 1. 121102
207 - 591 – 4215 Sebago Furniture www.sebagofurniture.com
1. Locate four sets of bed bolts,
washers and brass barrel nuts.
2. Start by attaching one rail to the
Footer.
3. Insert the Brass Barrel Nut in the
hole on the rail.
1. Align the Barrel Nut slots in the
direction of the bolt as shown in
the picture.
2. With one person holding the footer
steady insert the rail into the
Footer using the alignment pegs.
3. Rotated the walnut cover up on
the front of the Footer and insert
the bolt.
4. Align the bolt and start to thread
the bolt by hand. You may need
the slotted screwdriver to keep the
barrel bolt aligned in the direction
of the bolt. You may have to
wiggle the barrel nut to get the
threading started.
All manuals and user guides at all-guides.com

Rockland Bed Assembly Instructions, Rev 1. 121102
207 - 591 – 4215 Sebago Furniture www.sebagofurniture.com
1. DO NOT CROSS THREAD the
BARREL BOLT.
2. Align the first attached rail with the
Header.
3. Tighten snuggly with the socket
wrench.
4. Repeat the above process of
securing the 1st rail to the Header.
5. Carefully with another person align
the second rail to the Footer and
Header. Press the alignment pins
into the Header and Footer. Have
a second person hold the Rail
while securing the Rail with the
bed bolts.
PLATFORM ASSEMBLY
1. Locate the Platform piece marked
“H” on one end and #1 on the other
end.
2. Place it with the handhold tightly
against the Header on top of the
small wood blocks.
3. Next locate the next platform piece
marked #1-2, place it on the rails
facing the header.
4. Insert the tongue into the groove. If
your bed is a King you will need to
attach the support foot to the piece
marked #1-2, go to KING Foot
Assembly Instructions below
before proceeding.
All manuals and user guides at all-guides.com

Rockland Bed Assembly Instructions, Rev 1. 121102
207 - 591 – 4215 Sebago Furniture www.sebagofurniture.com
KING FOOT ASSEMBLY
1. Locate the King Support Foot and
four sets of screws, lock washers
and washers.
2. This foot attaches on the bottom
side of Platform marked #1-2.
3. Flip platform #1-2 over while it is
on the rails.
PLATFORM ASSEMBLY Cont.
1. Your bed may have three or four
platform pieces. Insert all as described
above EXCEPT the LAST one.
2. The Last Piece requires two people
and is marked with an “F”.
3. Place the last piece on the rails with
the handle hold at the footer end.
4. Insert the tongue in the groove of the
last piece tilted up at a slight angle so
as to not touch the footer top curved
arch.
5. Carefully push the last piece into the
groove and gently lower the last
platform piece onto the rails.
6. DO NOT REST THE PLATFORM
PIECE ON THE FOOTER TO AVOID
DENTING THE FOOTER.
7. Slide the entire platform forward
towards the Footer exposing the small
wooden blocks at the Header.
8. Place your mattress on the platform.
CONGRATULATIONS YOU ARE DONE!
ENJOY YOUR NEW BED
All manuals and user guides at all-guides.com

Rockland Bed Assembly Instructions, Rev 1. 121102
207 - 591 – 4215 Sebago Furniture www.sebagofurniture.com
Attaching the King Foot
1. Using a slotted Screw Driver attach
the foot using the four screws with
the lock washer on the screw first
followed by the plain washer.
2. Do not over tighten the screws.
3. The foot has been preset to the
proper height.
King Foot Height Adjustment
1. Flip the #1-2 Platform Panel over
and secure the tongue into the
groove.
2. The King Foot should be firmly on
the floor as shown.
3. If the foot needs adjusting use a
9/16” wrench to loosen the nut.
4. Adjust the foot so it is firmly against
the floor.
5. Re-tighten the nut.
6. Go back and proceed with the final
Platform Assembly Continued
instructions.
All manuals and user guides at all-guides.com