Hay NEW ORDER User manual

1
NEW ORDER TABLE
By STEFAN DIEZ
> INSTRUCTIONS MANUAL <
H AY

2
> INTRODUCTION <
New Order is born of 100% industrial production, reflecting
our ambition to create uncompromising and high-precision
quality products. Shelving and storing units form the backbone
of New Order Workspace Elements. Attached or detached
tables in different heights for sitting as well as standing
enable an almost infinite number of customized configurations.
New Order Table works as a free standing table for the dining
room, office or conference room but the functionality of the
table can be expanded with a set of connectors, allowing them
to hook directly onto a New Order shelf and literally merge
with it allowing for numerous workspaces to emerge.
Just like the vertical structure of New Order, the matching
tables are built from functional aluminium profiles that
are able to handle the infrastructure of cables often vital
for an office environment. The tables are available in
various standard sizes fitting the horizontal as well as
the vertical grid of New Order.

> CARE AND MAINTENANCE<
When you move the table, make sure to lift it rather than
pulling or pushing it, as that would damage the legs
and mountings. We recommend that you tighten up the
screws and nuts after one to two months’ use. Wood
and linoleum are natural materials, which may change
in colour and will patinate over time. To reduce changes
avoid placing the table in direct sunlight or near a heat
source. To avoid permanent stains, use coasters under
damp, hot or coloured objects. We recommend that you
avoid covering the surface partially, for example with
tablecloths or place mats, as colour variances may
appear. Always remove stains quickly before they can do
any permanent damage to the tabletop.
CLEANING
Powder coated aluminium / Clean with a damp cloth
wrung in a solution of water and a neutral detergent or
soap flakes. Remove soap residue immediately using a
clean, dry cloth. Avoid using scouring cream or scouring
pads, as they may scratch the surface.
Linoleum / Clean the tabletop with a clean cloth wrung
in water and a detergent suited especially for linoleum.
Follow up immediately with a clean, dry cloth.
Alternatively, stains may be carefully removed using
white spirit (mineral spirit) or a damp nano sponge with
dipped in lukewarm water or linoleum care. Never use
the nano sponge dry. Avoid using alkaline detergents
such as soft (yellow) soap, washing soda, lye and
scouring powder.
Lacquered wood / For daily maintenance, wipe the
surface with a clean, dry cloth. For cleaning, use a clean
cloth wrung in water or in a solution of water and a
neutral detergent (soap flakes) or a care product suited
especially for lacquered wood. Remove soap residue
immediately using a clean, dry cloth. To remove stains,
use a clean, damp cloth wrung in lukewarm water with
one part vinegar to nine parts water. Follow up
immediately with a clean dry cloth. If the surface is
scratched or appears matt, use lacquer care. Avoid
using detergents containing silicone, as that would seal
the stain in and make subsequent repairs more difficult.
Avoid using scouring cream or scouring pads, as they
may scratch the surface.

> CONTENTS<
PAGE 8-17
WITHOUT SUPPORT BAR
PAGE 18-31
WITH 1 SUPPORT BAR
PAGE 32-45
WITH 2 SUPPORT BARS
PAGE 46-60
WITH 3 SUPPORT BARS

8 9
> WITHOUT SUPPORT BAR<
Frame screw
x 48
Short frame profile
x 2
Torx keyLeg screw
x 4
Allen key
> PARTS<
Frame profile long
x 2
Tabletop x 1Leg x 4
Corner knot x 4

10 11
1.
MOUNTING CORNER KNOTS
Insert the two corner knots in the short frame profile. Make sure
the corner knots are pushed all the way in.
2.
MOUNTING FRAME PROFILES
Slide the frame profiles firmly onto the corner knots.

12 13
3.
ALIGNING FRAME PROFILE
In the other end of the table frame align and push the short frame profile into
the long frame profile.
4.
MOUNTING THE FRAME PROFILE
When mounting the frame profiles to the corner knot it is of great importance
that the two frame profiles align without gaps or unevenness.
CHECKING THE CONNECTION
Check the corners of the frame profiles. Avoid any
unevenness or gaps.
If these occur, placing the tabletop in the frame will
become unnecessarily challenging.

14 15
FRAME SCREWS
Locate the bag of screws named
Frame Screws
5.
SECURING THE FRAME PROFILES
Use the supplied torx key to fixate each corner using 8 screws.
x 32
6.
MOUNTING THE LEGS
Make sure that the legs are pressed firmly against and onto the corner knots leaving no gaps.
Any gaps can lead to difficulties when inserting the leg screws.

16 17
7.
MOUNTING THE LEGS
Firmly press all 4 legs onto the corner knots.
Insert the leg screws in the holes in the frame profile and secure the legs by
screwing in the leg screws using the supplied allen key.
x 4
LEG SCREWS
Locate the bag of screws
named Leg Screws
8.
INSERTING THE TABLETOP
Place the tabletop in the frame on the short frame profile.
9.
PUSHING THE MIDDLE
Push the center of the tabletop gently upwards while guiding the
free side of the tabletop into the frame.
10.
NUDGING
Work your way around the tabletop’s edge pushing down to ensure that it
rests well in the frame profile.

18 19
> WITH 1 SUPPORT BAR<
Connector x 2
Corner knot x 4
Short frame profile
x 2
> PARTS<
Support bar x 1Frame profile long
x 2
Support bar
connector x 2

20 21
Leg x 4
Leg screw
x 4
Torx keyAllen key Allen key
Frame screw
x 48
Support bar
screw x 8
Tabletop x 1
1.
MOUNTING CONNECTOR
Insert one connector in the short frame profile.
Repeat by inserting one connector in the other short frame profile.
2.
MOUNTING SUPPORT BAR CONNECTOR
Locate the mark on the short frame profile.

22 23
3.
ALIGNING SUPPORT BAR CONNECTOR
Locate the center mark on the frame profile. Align the support bar connector so that
the mark on it aligns with the mark on the frame profile.
4.
MOUNTING SUPPORT BAR CONNECTOR
Using the supplied allen key screw in the two support bar screws mounting
the support bar connector to the connector.
x 4
SUPPORT BAR SCREWS
Locate the bag of screws named
Support Bar Screws
5.
MOUNTING CORNER KNOTS
Insert the two corner knots in the short frame profile. Make sure
the corner knots are pushed all the way in.

24 25
6.
MOUNTING SUPPORT BAR AND FRAME PROFILES
Firmly push the support bar onto the support bar connector and slide the frame
profiles firmly onto the corner knots.
7.
ALIGNING SUPPORT BAR CONNECTOR SIDE
In the other end of the table frame align and push the short frame profile into
the long frame profile and support bar.

26 27
8.
SECURING SUPPORT BAR
Using the supplied allen key fixate the support bar to the support bar connector.
x 4
SUPPORT BAR SCREWS
Locate the bag of screws named
Support Bar Screws
9.
MOUNTING THE FRAME PROFILE
When mounting the frame profiles to the corner knot it is of great importance
that the two frame profiles align without gaps or unevenness.
CHECKING THE CONNECTION
Check the corners of the frame profiles. Avoid any
unevenness or gaps.
If these occur, placing the tabletop in the frame will
become unnecessarily challenging.

28 29
FRAME SCREWS
Locate the bag of screws named
Frame Screws
10.
SECURING THE FRAME PROFILES
Use the supplied torx key to fixate each corner using 8 screws.
x 32
11.
MOUNTING THE LEGS
Make sure that the legs are pressed firmly against and onto the corner knots leaving no gaps.
Any gaps can lead to difficulties when inserting the leg screws.

30 31
12.
MOUNTING THE LEGS
Firmly press all 4 legs onto the corner knots.
Insert the leg screws in the holes in the frame profile and secure the legs by
screwing in the leg screws using the supplied allen key.
x 4
LEG SCREWS
Locate the bag of screws
named Leg Screws
13.
INSERTING THE TABLETOP
Place the tabletop in the frame on the short frame profile.
14.
PUSHING THE MIDDLE
Push the center of the tabletop gently upwards while guiding the
free side of the tabletop into the frame.
15.
NUDGING
Work your way around the tabletop’s edge pushing down to ensure that it
rests well in the frame profile.

32 33
> WITH 2 SUPPORT BARS< > PARTS<
Connector x 2
Corner knot x 4
Short frame profile x 2Support bar x 2Frame profile long
x 2
Support bar
connector x 4

34 35
Leg x 4
Leg screw
x 4
Torx keyAllen key Allen key
Frame screw
x 48
Support bar
screw x 16
Tabletop x 1
1.
MOUNTING CONNECTORS
Insert two connectors in the short frame profile.
Repeat by inserting two connectors in the other short frame profile.
2.
MOUNTING SUPPORT BAR CONNECTORS
Locate the marks on the short frame profile.

36 37
3.
ALIGNING SUPPORT BAR CONNECTOR
Locate the outer mark on the short frame profile. Align the support bar connector so that
the mark on it aligns with the mark on the frame profile. Repeat on the other short frame profile.
4.
MOUNTING SUPPORT BAR CONNECTORS
Using the supplied allen key screw in the two support bar screws
mounting the support bar connector to the connector.
x 8
SUPPORT BAR SCREWS
Locate the bag of screws named
Support Bar Screws
5.
MOUNTING CORNER KNOTS
Insert the two corner knots in the short frame profile. Make sure
the corner knots are pushed all the way in.

38 39
6.
MOUNTING SUPPORT BARS AND FRAME PROFILES
Firmly push the support bars onto the support bar connectors.
Slide the frame profiles firmly onto the corner knots.
7.
ALIGNING SUPPORT BAR CONNECTOR SIDE
In the other end of the table frame align and push the short frame profile
into the long frame profile and support bars.