SECO-LARM ENFORCER EV-Y1501-AMWQ User manual

4-in-1 HD TVI, CVI, AHD, Analog
Bullet Cameras
Manual
Select between multiple formats:
TVI, CVI, AHD, and Analog
5MP Resolution
ICR Module
Joystick OSD Control
DNR (Digital Noise Reduction)
D-WDR (Digital Wide Dynamic Range)
Rugged, weatherproof (IP66) construction
Cables concealed in bracket to
prevent tampering
Features:
Model # Lens Resolution Voltage Style Color
EV-Y1501-A2WQ 2.8mm 5MP 12VDC Bullet White
EV-Y1501-AMWQ 2.8~12mm 5MP 12VDC Bullet White
EV-Y1501-
A
2WQ shown

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras
2SECO-LARM U.S.A., Inc.
Specifications:
Model EV-Y1501-A2WQ EV-Y1501-AMWQ
Type Fixed Bullet Camera Varifocal Bullet Camera
Formats TVI (Default) / CVI / AHD / Analog (CVBS)
CMOS 1/2.7" 5MP CMOS
Resolution (HD) 2592x1944
3DNR No
2DNR Yes
D-WDR Yes
OSD (On-Screen Display) Yes
Cable OSD control Yes
Megapixels 5MP
Lens 2.8mm ICR 2.8~12mm ICR
Viewing angle 121° 38°~138°
# of IR LEDs 18 (SMT) 30 (SMT)
IR Range Up to 50ft (20m) Up to 115ft (35m)
FPS 20FPS
F Stop F2.0
Minimum
illumination
IR On 0Lux
IR Off 0.05Lux
S/N Ratio 35dB
Shutter control Auto
Gain control Auto
Operating voltage 12VDC
Current draw IR On 320mA 350mA
IR Off 80mA 80mA
IP Rating IP66
Operating temperature -22°~131° F (-30°~55° C)
Dimensions 51/2" x 23/4" x 213/16"
(140x69x71 mm)
97/16" x 3" x 35/16"
(240x77x84 mm)
Weight 12.3-oz (349g) 1-lb 12.4-oz (805g)
Dimensions:
1x Bullet camera 3x Screws 3x Screw anchors 1x Manual
1x Mounting template 1x Hex wrench 1x Power balun 1x OSD Manual
Parts List:
®
EV-
Y
1501-AMWQ:EV-
Y
1501-A2WQ:
97/16" (240mm)
57/8" (150mm)
51/2" (140mm)
415/16" (126mm)
23/4"
(
69mm
)
3"
(77mm)
21/4"
(58mm)

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras
SECO-LARM U.S.A., Inc. 3
Overview:
Installation:
Important: Do not cut any wires as the warranty will be voided.
1. Run a 12VDC power supply wire and a video cable
with a male BNC connector to the wall or ceiling
where the camera is to be mounted.
2. Temporarily connect the camera to the 12VDC
power supply.
3. Temporarily connect the camera’s female BNC
connector to the video cable’s male BNC connector.
4. While watching the monitor, hold the camera against
the wall or ceiling by hand where it is to be mounted,
then turn the camera until it is certain that this
mounting location is correct.
5.
A
djust the zoom and focus to desired settings. See
"Zoom and Focus Adjustment" (EV-Y1501-AMWQ
only).
6. Use the OSD controller's joystick to adjust the camera
settings. See "OSD Controller Settings". (For more
information, see separate OSD manual).
7. Use a pencil and the included mounting template
sticker to mark the mounting location. Disconnect the
12VDC power supply and video cable.
8. Mount the camera mounting base to the wall using the
included mounting screws.
OSD Controller Settings:
To set format via the OSD controller, move the
controller in the direction of the desired setting,
hold for 5 seconds, and release when the
camera restarts.
See chart below.
Direction Format Setting
Up
A
HD
Down CVBS/Analog
Left TVI
Right CVI
UP
DC Jac
k
Female BNC
Connector
OSD controller
Sunshield screwSunshield
Mounting arm
adjustment screw
Camera angle
adjustment screw
Mounting
screws
EV-Y1501-
A
MWQ shown above.
Zoom & Focus Adjustment*:
To adjust the Zoom and Focus, open the Zoom/Focus compartment
located on the bottom of the camera. Once within the compartment,
use a flathead screwdriver to loosen the Zoom and Focus screws to
allow for adjustment.
Focus
To focus in on close objects, push
the focus screw right towards "N".
To focus out on far objects, push
the screw right towards "F".
Zoom
To zoom in, push the zoom screw
left towards "T". To zoom out, push the
screw right towards "W".
1. Use the camera within the given temperature
and voltage limits.
2. Do not point the camera at the sun.
3. Do not subject the camera to strong vibrations.
4. Do not mount the camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals.
Before Starting:
Mounting base
*EV-Y1501-
A
MWQ only.
(Continued next page)
Zoom
Focus
To adjust the camera angle and positioning,
loosen the camera angle adjustment screw
and mounting arm adjustment screw.
Rotate the camera and position the
mounting arm in the desired position and
retighten the screws.
Camera arm position:
Camera Angle and Positioning:
Mounting arm
adjustment screw
Camera angle:
Camera angle
adjustment screw
NF
T W
Base
Front
BNC
Connector
Camera
NOTE: Do not press joystick in when setting different modes.
Zoom and focus
compartment

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras
4SECO-LARM U.S.A., Inc.
The screen is blank.
Check that the camera is powered up.
Check that the power supply's polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the monitor is
connected properly.
The screen image is dim. Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image has poor contrast. Adjust the monitor's contrast knob.
Change the position of the camera.
The screen image flickers. Change the position of the camera, check cables and format setting
The screen image is distorted. Change the position of the camera, check cables and format setting
The camera case is hot. Check that the correct power supply is in use.
Installation (continued):
®PICRN3
MI_EV-Y1501-
A
xWQ_191206.doc
x
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be
held responsible for the use of this product in violation of any current laws or statutes.
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Phone: [phone] | [phone] Email: [email protected]
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
Troubleshooting:
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric
shock. Do not open the case of this device, as there are no user-serviceable components inside.
Do not cut any wires as the warranty will be voided.
9. Reconnect the 12VDC power supply and video cable.
10. Turn the monitor on and confirm the camera is sending the proper video signal.
11. Adjust the camera to the desired angle and position. See "Camera Angle and Positioning" for more information.
12. Do a final test of the video camera and monitor.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
re
q
uirements and void user’s authorit
y
to o
p
erate the device.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A., Inc. All
rights reserved.