SECO-LARM SLI ENFORCER EV-Y6501-A3WQ User manual

®
EV-Y6501-A3WQ
4-in-1 HD TVI, CVI, AHD, Analog
Covert PIR Camera
Manual
Features:
 Select between multiple formats:
TVI, CVI, AHD, and Analog
 Joystick OSD Control
 D-WDR (Digital Wide Dynamic Range)
 Camera is hidden in a non-functioning
PIR sensor housing
 1/2.8" 5MP Sony CMOS
 3.7mm Covert pinhole lens
 18 Covert IR LEDs for discreet monitoring
 1440p Resolution
 2DNR (2D Digital Noise Reduction)

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Covert PIR Camera
2 SECO-LARM U.S.A., Inc.
1x
Camera
2x
Mounting screws
1x
Mounting bracket
1x
Manual
1x
DC Plug with Terminal Block
2x
Screw anchors
1x
Mounting bracket ball
Parts List:
Dimensions:
Specifications:
Type Covert PIR Camera
Formats TVI (Default) / CVI / AHD / Analog
CMOS 1/2.8" 5MP Sony CMOS
Resolution (HD) 2592x1944, 1440p
2DNR Yes
D-WDR Yes
OSD (On-Screen Display) Yes
Cable OSD control Yes
Video output BNC
Megapixels 5MP
Lens 3.7mm Pinhole lens
Viewing angle 120°
# of IR LEDs 18 Covert (940nm)
IR Range Up to 50ft (15m)
FPS 20
F Stop 2.2
Minimum
illumination
(IR On) 0.1 Lux
(IR Off) 0.01 Lux
S/N Ratio >50dB
Gain control Yes
White balance Auto, Day & Night
Shutter control AES (Auto Electric Shutter), 1/60~1/50,000 s
Current draw (IR On) <3.5W
(IR Off) <2W
Operating voltage 80mA@12VDC
Operating temperature -4°~140° F (-20°~60° C)
Dimensions 41/16"x23/8" x15/16" (104x60x34 mm)
Weight 12.3-oz (350g)
15/16" (34mm)
2"
(
52mm
)
23/8"
(60mm)
41/16"
(104mm)

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Covert PIR Camera
SECO-LARM U.S.A., Inc. 3
Overview:
DC Jack
Important:
Do not cut any wires as the warranty will
be voided.
Female BNC connector
DC Plug with terminal block
Camera
pinhole
Mounting bracket
Slide camera
downward onto
the mounting
bracket
OSD Controller
Mounting bracket ball
Before starting:
1. Use the camera within the given
temperature and voltage limits.
2. Do not point the camera at the sun. Heat
can damage the camera even when not
in use.
3. Do not subject the camera to strong
vibrations.
4. Do not mount the camera in areas exposed
to radiation, str
ong magnetic fields, or strong
electrical signals.
Installation:
1.
Run a 12VDC power supply wire and a
video cable with a male BNC connector
through the wall to where the camera will
be mounted.
2. Connect the camera’s video and power
cables.
3. Temporarily mount the camera to test its
function and display.
4. Do a preliminary test of the camera to
ensure it will work properly. Partially screw
a screw into the wall where the top of the
bracket should go. Slide the bracket onto
the screw. Finish securing the top of the
bracket to the wall.
5.
Secure the bottom of the bracket to the wall.
6. Attach the mounting bracket ball to the
mounting bracket by gently pushing the ball
into the bracket.
7. Attach the camera to the assembled bracket
by sliding the camera downward.
8. Do a final test of the video camera and
monitor.
9. Program the camera if needed via the
attached OSD joystick.
NOTE: For the OSD manual,
download from the
camera’s product page on www.seco-larm.com.
OSD Controller Settings:
To set format via the OSD controller, press
the controller in the direction of the desired
setting, hold for 5 seconds, and release
when the camera restarts.
See chart to the right.
Direction
Format Setting
Up
C
VBS
Down
CVI
Left
AHD
Right
TVI
Camera
Power
UP
DN
L
R

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Covert PIR Camera
4 SECO-LARM U.S.A., Inc.
SECO-LARM
® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email:
sales@seco
-
larm.com
®
PICVN3
MI_EV
-
Y6501
-
A3WQ_200429.docx
The screen is black
 Check that the camera is powered up
 Check that the power supply’s polarity is correct
 Check that the monitor is powered up
 Check that the video cable connecting the camera to the
monitor is connected properly
The image is foggy or washed out
at night
 Check that there are no objects very close to the camera
 Check that there are no highly reflective objects in the scene
The screen image is dim  Clean the lens using a soft, clean cloth
 Check that the light source is adequate
The screen image has poor contrast  Adjust the monitor’s contrast knob
 Change the position of the camera
The screen image flickers  Change the position of the camera, check cables and
format setting
The screen image is distorted  Change the position of the camera, check cables and
format setting
The camera case is hot  Check that the correct power supply is in use
IR LEDs do not turn on  Check that the correct power supply is in use
Troubleshooting:
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no user-serviceable components inside.
Do not cut any wires as the warranty will be voided.
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local l
aws
and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held
responsible for the use of this product
in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2)
THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user
’s authority to
operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitt
ed.
Any change to the antenna or the device could result in the device exceeding the RF expo
sure requirements and void user’s authority to
operate the device.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three
(3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective
part
if the unit is returned, transportation prepaid, to SECO-
LARM. This Warranty is void if damage is caused by or attributed to acts of God,
physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty ins
tallation, or if for any other
reason SECO-
LARM determines that such equipment is not operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be l
imited to the replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-
LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-
LARM reserves the right to
change specifications without notice. SECO-
LARM is also not responsible for misprints. All trademarks are the property of
SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A., Inc. All rights reserved.