Second Story Home Lark User manual

B O X C O N T E N T S
A. 0 HEADBORD x1
B.
0 FOOTBOARD x1
C.
0 SIDE PANEL x2
D.
0
E. 0
BOTTOM PANEL x2
F.
0
WOODEN STABILIZER x4
G.
0
SIDE BRACKET x4
SUPPORT BRACKET x 6
I. 0ALLEN WRENCH x1
H.0ALLEN BOLT x28
B. QTY1
D. QTY4
F. QTY4
C. QTY2
A. QTY1
G. QTY6
J. QTY1
E. QTY3
H. QTY28

WHAT YOU WILL NEED
C.0SIDE PANEL x2
F.0SIDE BRACKET x4
G.0SUPPORT BRACKET x6
H.HG0ALLEN BOLT x20
ALLEN WRENCH x1I. 0
FIGURE 1
02
FIGURE 2
WHAT YOU WILL NEED
C.
0
SIDE PANEL x2
F.
0
SIDE BRACKET x4
G.
0
SUPPORT BRACKET x6
H.
HG0
ALLEN BOLT x20
HG0ALLEN BOLT x20HG0
ALLEN WRENCH x1
I.
0
STEP: 01
STEP: 02
SET SIDE BRACKET ( F ) ON THE SIDE PANEL ( C ) AS SHOWN BELOW IN
EXAMPLE 1. PLACE BRACKET SO THE TWO HOLES ARE AGAINST THE FABRIC.
NEXT, PLACE THE LARGER BOLT ( H ) INTO THE TWO HOLES AND TIGHTEN
USING ALLEN WRENCH ( I ) AS SHOWN IN EXAMPLE 2. DO NOT OVER-
TIGHTEN. REPEAT UNTIL ALL FOUR BRACKETS HAVE BEEN ATTACHED
ON BOTH THE SIDE PANEL ( C ).
SEE FIGURE 1
SEE FIGURE 2
USE THE ALLEN BOLTS ( H ) AND LOOSELY SCREW THEM INTO THE FOUR
HOLES IN THE MIDDLE OF THE SIDE PANEL. THE SUPPORT BRACKET ( G )
WILL BE PLACED BEHIND THE WASHER. ONCE IS IS SECURED, TIGHTEN THE
SCREWS. DO NOT OVERTIGHTEN.

wHAT YOU WILL NEED
03
A. HEADBOARD
B. FOOTBOARD
E. WOODEN STABILIZER
H. ALLEN BOLT
I. ALLEN WRENCH
STEP 05
STEP 03
D. BOTTOM PANEL
WITH BOTH THE HEADBOARD ( A ) AND FOOTBOARD ( B ),
USE THE REMAINING 8 ALLEN BOLTS ( H ) TO SCREW
INTO FOUR BOTTOM HOLES ON EACH OF THE PIECES.
LEAVE THESE BOLTS LOOSE.
STEP 05
STEP 04
TAKE THE HEADBOARD ( A ) AND ALIGN THE BOLTS
TO THE SIDE BRACKET ( F ) THAT IS ALREADY
ATTACHED TO ONE OF THE SIDE PANELS. ONCE
PLACED INSIDE THE HOLE, PRESS DOWN TO LOCK
THE BOLT IN PLACE. DO SO UNTIL BOTH THE HEAD-
BOARD ( A ) AND FOOTBOARD ( B ) ARE ATTACHED
TO THE SIDE PANELS ( C ). ONCE ALL PIECES ARE
ATTACHED, BEGIN TO TIGHTEN EACH OF THE
BOLTS USING THE ALLEN WRENCH ( I ).
PLACE BOTH WOODEN STABILIZER ( E ) INSIDE THE STABILIZER
BRACKET TO SECURE THEM IN PLACE. LAY BOTTOM PANELS
OVER WOODEN STABILIZERS.
STEP 06
BOTTOM PANELS
STEP 0
3
WITH BOTH THE HEADBOARD ( A ) AND FOOTBOARD ( B ),
USE THE REMAINING 8 ALLEN BOLTS ( H ) TO SCREW
INTO FOUR BOTTOM HOLES ON EACH OF THE PIECES.
LEAVE THESE BOLTS
LOOSE
.

04
CARE AND MAINTENANCE
PERIODICALLY CHECK YOUR BED FOR ANY LOOSE BOLTS AND SCREWS
AND TIGHTEN WHERE NEEDED. IF BED IS DAMAGED, DO NOT USE.
CONTACT US FOR REPLACEMENT PARTS. SPOT CLEAN ONLY. AVOID
EXCESS MOISTURE.
PLEASE VISIT OUR WEBSITE AT WWW.SECONDSTORYHOME.COM. THERE, YOU CAN FIND MORE PRODUCT INFORMATION,
REGISTER YOUR PRODUCT, CONTACT US OR REQUEST REPLACEMENT PARTS.
YOU CAN EMAIL OR WRITE
[email protected]
SECOND STORY HOME
1477 DAVRIL CIR
CORONA, CA 92878
ONE YEAR LIMITED WARRANTY
CONTACT US
DEFECTIVE PARTS WILL BE REPLACED WITH A ONE YEAR PERIOD FROM DATE OF ORIGINAL PURCHASE. MISSING PARTS WILL BE
REPLACED WITHON 30 DAYS FROM THE DAY OF ORIGINAL PURCHASE. SECOND STORY HOME WARRANTS ONLY NEW UNITS PUCHA-
-SED IN IT’S ORIGINAL PACKAGING. THE WARRANTY DOES NOT COVER USED, SECOND HAND OR DEMOS AND IS NON-TRANSFERABLE.
ANY DAMAGED OR DEFECTIVE PART THAT RESULTS FROM NORMAL WEAR AND TEAR, ABUSE, NEGLIGENCE, IMPROPOSER USE OR
ALTERNATION TO THE FINISH, DESIGN AND HARDWARE OF THE BED, OR THE ASSEMBLY OF THIS PRODUCT ARE NOT COVERED. THE
SPECIFIC LEGAL RIGHTS OF THIS WARRANTY MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW ANY EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS.
ON
E
YEAR LIMITED WARRANTY
DEFECTIVE PARTS WILL BE REPLACED WITH A ONE YEAR PERIOD FROM DATE OF ORIGINAL PURCHASE. MISSING PARTS WILL BE
REPLACED WITHON 30 DAYS FROM THE DAY OF ORIGINAL PURCHASE. SECOND STORY HOME WARRANTS ONLY NEW UNITS PUCHA-
-SED IN IT’S ORIGINAL PACKAGING. THE WARRANTY DOES NOT COVER USED, SECOND HAND OR DEMOS AND IS NON-TRANSFERABLE.
ANY DAMAGED OR DEFECTIVE PART THAT RESULTS FROM NORMAL WEAR AND TEAR, ABUSE, NEGLIGENCE, IMPROPOSER USE OR