Aqua One Cabinet 53445 User manual

Assembly Instructions
Please keep for future reference.
Important - Please read these instructions fully before starting assembly
Version 1 - 25/11/19
150cm Cabinet
Suitable for AquaSys 395 or ReefSys 434 Aquariums
AquaSys ReefSys
by

Safety Care and Advice
IMPORTANT: Please read these instructions before starting assembly
• Warning: This unit is heavy.
Please lift with care.
• Check you have all the components
and tools listed.
• Remove all ttings from the plastic
bags and separate them into their
groups.
• Keep children and animals away from
the work area, small parts could choke
if swallowed.
• Parts of the assembly will be easier
with 2 people.
• Make sure you have enough space
to layout the parts before starting.
• Assemble the item as close to its
nal position (in the same room) as
possible.
• Assemble on a soft level surface to
avoid damaging the unit or your
oor (use opened out unit carton).
• We do not
recommend the use
of power drill/
drivers for inserting
screws, as this could
damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging carefully and
responsibly.
Care and maintenance
Contact Us
• Only clean using a damp cloth and
mild detergent, do no use bleach or
abrasive cleaners.
• From time to time check that there
are no loose screws on this unit.
• This product should not be discarded
with household waste. Take to your
local authority waste disposal centre.
Aqua Pacic UK Ltd.
Unit 1, Mauretania Road, Nursling
Industrial Estate, Southampton
SO16 0YS
Tel [phone]
Fax [phone]
sales@aquapacic.co.uk
www.aquaone.co.uk
Tools
Measuring
Tape
Spirit Level Cross-head
screwdriver
Hammer
Eye protection
(when using a
hammer)
Silicone
Silicone

Panels
Please check you have all the panels listed below.
2x Side panels
764 x 530mm
2 x Wide back brace
764 x 200mm
1x Base
1504 x 531mm
3x Door
786 x 496mm
BA
C D
E1x Narrow front brace
764x100mm
F
2x Back brace
764 x 200mm
G
1x Top
1504 x 531mm
1x Divider
764 x 512mm
H

Fittings
Please check you have all the ttings listed below.
40x 15mm Large
Locking Cam Nut 40x Cam Bolts
1 2 6x Hinges 3
6x Hinge Plates
48x Hammer-in Glides 518x 3.5x15mm Screws 6
3x Push Catch
71x Aperture Trim Ring 8
4x Short Cam Bolts
9

Step One
Lay side panels (A) on the
oor with holes facing
upwards.
Fit 6x Cam ttings (1) into
larger holes with cross facing
up and the arrow facing the
edge of the board.
Screw 3x Cam Bolts (2) into
the 5mm holes along the back
edge.
Attach the hinge plates (4)
to the sides that has the two
pairs of 5mm holes at the
front edge with the at edge
at the front.
Repeat on all (A) panels.
A
1
1
1
1
1
1
A
2
2
2
A
4
4

Step Two
Fit Cam Fittings (1) into the 7 holes of the Wide Back Braces (B) and into the four holes into back
braces (G).
Attach the raw edge of the Wide Back Braces to the back edge of the sides giving the Cam Fittings
a half turn with the screwdriver.
Repeat for all panels and braces.
1
1
1
1
1
1
1
B
1
1
1
1
G
A
B

H
1
1
1
1
1
1
Fit 6 Cam Fittings (1) into larger
holes on divider (H) with cross
facing up and the arrow facing
the edge of the board.
Attach the two hinge plates (4)
to the side of divider (H) that
has the two pairs of 5mm holes
at the front edge with the at
edge at the front.
Step Three
H
4
4

Step Four
Using a hammer, t glides (5) to the underside of the base panel (C) using the pip marks as a guide
for tment then turn the base over to have the 5mm holes facing upwards.
Screw in cam bolts (2) into all of the 5mm holes with the exception of the two on the front edge
which should have short Cam Bolts (9).
Turn over
C
5
5
5
5
5
5
5
5
C
2
2
222
2
2
2
2
2
2
2
99
2
2
222
C

B
A
Step Five
Drop sides with attached back braces onto the cams on the base. Similarly attach the back
braces (G) to the centre of the base at the back. Drop divider (H) into position on the Cam Bolts
with Hinge Plates on the right hand face.
Give all cam ttings a half turn with the screwdriver.
A
B
G
G
H
C

Step Six
Lay top panel (D) with holes facing upwards, screw cam bolts (2) into all 5mm holes with
exception of the 2 holes at the front edge next to the pip marks which should have the
remaining 2 short cam bolts (9) tted.
Using 4 of screws (6) attach the brackets for the push catches (7) with the arrows facing
forwards, to the pip marks then attach the push catch to the bracket by clipping in at the back
and pushing down at the front until you hear a click.
Turn top over and attach to sides and back braces and the divider (H) as with the base.
Turn over
2
D
2
222
2
2
7
6
67
6
6
2
2
2
2
2
2
2
22
2
7
6
6

G
C
A
B
AG
B
Step Six Continued

Step Seven
From the inside of the
cabinet push aperture trim
ring (8) through the hole in
the top of the cabinet.
We highly recommenced
securing with silicone to
seal the edge and protect
the chipboard.
Silicone
A
A
C
D

Clip narrow front brace (F)
over the short cam bolts
and tighten in a similar
manner to all the others.
Step Eight
F
C
A
D

Step Nine
Lay doors (E) on oor with
the hinge holes facing
up, place hinges (3) into
holes and screw in using
remaining screws (6).
Hook hinge arms into the
front of the hinge plate and
push in at the back of the
arm until they click. Adjust
hinges using adjustment
screws as necessary.
Adjust the push catch (7) as
necessary by twisting in or
out.
6
6
66
E
3
3
7
E
A
D
C