Secufirst DID701 S User manual

DID701 S / B / BB
Wi-Fi doorbell with wireless bell
Big Manual

This big manual would help you through all the
possible questions you might have during the use of
the camera. Below is the overview of the topics within:
1. Product Overview P03~P08
2. How to Install P09~P17
3. Preparation Before Setup on Smart Device P18~P19
4. Camera Setup on Smart Device P20~P28
5. Add Second Smartphone/Tab P29~P31
6. Notification Setting P32~P35
7. Advance settings P36~P68
8. Connect Wired Internet P69~P74
9. Record motion detection P75~P82
10.Playback recording P83~P88
11.Connect a wireless chime P89~P93

Product Overview
3

Product Overview – Wi-Fi Doorbell
4
Lens
Microphone
Light Sensor
Push Button
Loud Speaker
Rubber cover
For wiring
Wall mount holder

Product Overview – Wi-Fi Doorbell
5
1
2
3
4
5
1. Reset button (Hold for 10 seconds)
2. Connection Wired Chime indoor (C1, C2 / 0V)It's only possible to
connect a Mechanical Chime which is powered by an 8V AC
transformer. The separate power supply is AC, so it doesn't matter
which wire goes to C1 and C2.
3. RJ45 internet cable connection (TD-, TD+, RD-, RD+)
Note, an internet cable has 8 wires. We only need 4 wires to connect to
the Wi-Fi Doorbell.
TD- = Internet cable, Orange color wire
TD+ = Internet cable, Orange / White color wire.
RD- = Internet cable, Green color wire.
RD+ = Internet cable, Green / White color wire.
Note, wired internet only works when you firstly connect the internet cable to
the Wi-Fi Doorbell and router. After that, insert the adapter in the socket.

Product Overview – Wi-Fi Doorbell
6
1
2
3
4
5
4. Adapter connection (V+, V- / 12V 1A)
V+ = Red Wire V- = Black wire
Note, pay attention to connect correctly!!!
5. Connection for electrical lock (B1 + B2 / 0V).

Product Overview – Wireless Bell
7
Loud Speaker Volume Settings
No function when
bundle using with Wi-
Fi Doorbell
No function when
bundle using with Wi-
Fi Doorbell

Product Overview – APP
8
The camera comes with free to download app called
“SecuFirst HD Professional Edition”
You could scan below QR code to download the app.
Android Phone
Scan Here
iOS Phone
Scan Here

How to install
9

How to install
Remove the rubber cover on the backside of
the Wi-Fi Doorbell.
Connect the adapter with the extension cord.
Use the screwdriver to punch a hole into the
rubber cover.
Insert the extension cord through the rubber
cover.
Connect the extension cord to the Wi-Fi
Doorbell (V+ red wire, V- black wire). After that,
insert the adapter into the power socket.
Close the rubber cover again.
Note, don't connect an internet cable during the
installation.
See below pages for connection diagram
10

How to install
11

How to install
12

How to install
13

How to install
14

How to install
15

How to exchange SD Card
16
Pre installed 16GB micro sd card. If you want to exchange to a bigger
micro sd card, follow the below steps.
1. Please remove the screws and rubber cover in the back of the
metal housing first.
2. Slide the camera upward to separate the camera with metal
housing.
3. Remove the rubber cover of the Micro SD Card slot on the left
side of the camera.
4. Insert the Micro SD Card and put back the rubber cover.
5. Slide the camera back in the metal housing.
Note, a micro sd card can be 16, 32 , 64 or 128GB. Do not use a
bigger card. The specs of a suitable micro sd card is Maximum
128GB, UHS1 and class 10

How to install – Wall Mount A) Install the bracket where the previous doorbell was,
next to the door, with the 2 small screws included or the
anchors when necessary.
Make sure the wires are fed through the appropriate
square opening in the bracket. Then line up the video
doorbell on the bracket and slide down until secure.
Once installed, turn power back on. Wait until the LED
ring repeatedly flashes 3 times (approximately 1.5
minutes for the unit to re-boot) and you are able to start
the device setup.
B) The bracket included has slight angle which could be
used for different installation needs. If more angle
needed on the other side, simply turn the bracket upside
down and follow the installation instruction.
Or go to YouTube and search “SecuFirst DID701”
You could find more instruction videos for setup and
installation.
17
A B

Preparation before Setup on Smart Device
18

Preparation before installation To install this camera you need to prepare the following information:
1. Your own Wi-Fi name, and your own Wi-Fi password.
•The camera must be registered on your own Wi-Fi
network during this installation.
•Please note, it is our help desk number 1 problem that
customers enter their own Wi-Fi network password
incorrectly during this installation. The result is that the
camera cannot connect and will not display an image.
Check your Wi-Fi password carefully (on the back of the
router / own documentation).
2. Think of a new security password and document it carefully.
3. Security password: Provides access to live video images from
your Wi-Fi camera. During the installation with the app you will be
asked to change this password. Make up this passwords in
advance to move faster through the installation.
The new password need to contain:
A) At least 12 characters.
B) At least one capital letter (Example: A)
C) At least one lowercase letter (Example: a).
D) At least one digit (Example: 1).
E) At least one reading sign (Example:!).
* During the installation, keep your phone or tablet close to the
camera (max. 1 meter)
19

Camera Setup on Smart Device
20