Securitytronix ST-IP-DVF-1 User manual

ST-IP-DVF-1
ST-IP-DVF-2
HD Mini Network Dome Camera Quick Start Guide
Version 1.0.0

ii
Welcome
Thank you for purchasing our Networkcamera.
This Quick Start Guide is designed to get yoursystem up and running as easily as possible.
This document applies to both the ST-IP-MD36-1 and ST-IP-MD36-2 camera models (1mp & 2mp).
Please read the following safeguard and warnings carefully before you use this camera.
Please keep this document for futurereference.
Important Safeguards and Warnings
1．Electrical safety
All installation and operation should conform to your local electrical safetycodes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated 12V DC, DC5V or AC24V in the IEC60950-1. (Power supply
requirement is subject to the camera label).
Please prevent the line cord from being crushed or damaged, especially at the plug, power socket and
the junction from the camera.
Note: Do not connect a PoE power source AND a power supply to the camera at the same time;
it may result in camera damage.
We assume no liability or responsibility for fires or electrical shock caused byimproper handling or
installation.
We are not liable for any problems caused by unauthorized modification or attemptedrepair.
2．Environment
Don’t aim the camera at strong light (such as lighting, sunlight and so on) to focus; otherwise it
may cause overexposure, which will affect the longevity of the CCD or CMOS imager.
Please transport, use and store the camera within the range of allowed humidity and temperature. Don’t
keep the camera in a place which is wet, dusty, extremely hot, and extremely cold and with strong
electromagnetic radiation or unstablelighting.
Please do not allow water and other liquids to enter the camera, to prevent the internal
components from being damaged.
Please allow adequate ventilation around the camera to prevent heataccumulation.
Please pack the camera with the standard factory packaging or material with the same quality
when transporting the camera.
Avoid bumps and humidity during transportation, storage and installation.

ii
3. Operation and Daily Maintenance
Please do not dismantle the camera; Doing so may void your warranty.
It is recommended to use this camera with a surge-protection device.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of
the camera.
Do not touch the CCD (CMOS) optic component directly. You can use an air blower to clean the dust
or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the dust gently if it is
necessary to clean.
Always use a dry, soft cloth to clean the camera. If there is too much dust, please use the water to dilute
mild detergent first and then use it to clean the camera. Finally use the dry cloth to clean the camera.
Don’t use volatile solvents like alcohol, benzene, thinner etc or strong detergents with abrasiveness,
otherwise it will damage the surface coating or reduce the working performance of the camera.
The dome cover is an optical element, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods to clean a dirty lens:
Stained with dirt:
Use an oil-free soft brush to gently remove it.
Stained with grease or fingerprints:
Use a soft cloth to wipe the dome gently to dry it, then use oil-free cotton cloth or paper soaked with
alcohol or detergent to wipe from the lens center to outward. It is ok to change the cloth and wipe
several times to get all of the dirt off.
Warning
Please use the standard accessories provided by SecurityTronix and make sure the camera is
installed and repaired by professional engineers.
Do not use more than one power supply modes for the camera, otherwise it may cause damage to the
camera.
Statement
Please refer to the actual product for more details; this manual is just forreference.
Please contact the supplier or customer service if there is any problem occurred when using the
camera.
Please contact the customer service for the latest procedures and supplementary documentation.
There may be deviations between the actual value of some data and the value provided in the manual
due to the reasons such as the real environment is not stable and so on.

3
Please refer to the disk for more details, check and download corresponding user’s manual and tool.
Before installation, please open the package and check all the components areincluded.
Contact your local retailer ASAP if something is broken in yourpackage.
Accessory Name Amount
Network Camera Unit 1
Quick Start Guide 1
Installation Accessories Bag 1
CD 1

4
Table of Contents
1 Structure........................................................................................................................ 1
1.1 Components....................................................................................................... 1
1.2 Physical Properties ............................................................................................ 2
1.3 Alarm Setup....................................................................................................... 3
2 Camera Installation........................................................................................................ 4
2.1 Installation Steps................................................................................................ 4
2.2 Micro SD Card Installation.................................................................................. 6
2.3 Lens Adjustment ................................................................................................ 7
3 Network Configuration................................................................................................... 8
3.1 Modify IP Address.............................................................................................. 8
3.2 Login WEB Interface.......................................................................................... 9

1
1 Structure
Note:
The following diagram is for reference only, to illustrate the camera component and cable port
functions.
Camera component and cable port function may differ according to different models, please refer to
the actual camera for details.
1.1 Components
Refer to the following figure for hardware configuration. See Figure 1-1.
Figure 1-1 Component functions
Please refer to the following sheet for detailedinformation.
Component Component Name
Component 1 Dome camera module
Component 2 Dome enclosure

2
Port Port Name Note
Port 3Power input port Connect to DC 12V power, input power.
Port 4I/O port Alarm signal input/output (optional,
not supported by ST-IP-DVF-1 / 2)
Port 5Internet access port Network data in/out and PoE.
Note:
Some cameras do not support PoE.
Port 6Audio input port
Input audio signal, receive analog audio
signal from a microphone (optional, not
supported by ST-IP-DVF-1 / 2).
Port 7Audio output port Output audio signal to speakers (optional,
not supported by ST-IP-DVF-1 / 2)
Please refer to the following sheet for detailed information about I/Oport.
Port
Name Port Sequence Port name Function Description
I/O Port
1ALARM_IN1 Alarm input port, receive on-off signal of
external alarm source.
2ALARM_OUT1 Alarm output port, output alarm signal to
alarm camera.
3ALARM_GND Connect ground
Please refer to the following two figures for dimension information. The unit is mm. See Figure1-2
Figure 1-2 Dimension illustration

3
Note:
Alarm is not supported by ST-IP-DVF-1 / 2
Alarm input, output description:
Step 1 Connect alarm input device to the alarm input of I/Ocable.
Step 2 Connect alarm output device to the alarm output of I/O cable, alarm output isNormally
Open circuit output which connects a10K resistor to 3.3Vexternally.
Step 3 Open the Web, set alarm input and output correspondingly. Alarm input on WEB
corresponds to the I/O cable on the camera. When an alarm is triggered,the alarm input
device will generate asignal of high and low level. Set corresponding NO and NCinputs.
Step 4 Set the WEB alarm output. The alarm output corresponds to the alarm port wires of the
camera.
Please refer to the following figure for alarm input information. See Figure1-3.
Alarm input: When the input signal is idle or grounded, the camera can collect the different statuses of
the alarm input port. When the input signal is connected to 3.3V or idle, the camera collects the logic
“1”. When the input signal is grounded, the camera collects the logic“0”.
Figure 1-3
Please refer to the following figure for alarm output information. See Figure1-4
When alarm output is OC, it needs to increase pull-up resistance externally to work normally; output
signal uses a high and low level. After external pull-up resistance is increased, the default of the output
signal is high level, and it switches to low level when there is an alarm output.
The working current of alarm output port is recommended as <= 10mA. The max current which is used
to drive external circuit is 80mA, it is advised to add a relay if it is beyond thevalue.
Figure 1-4

4
Different models may have different ways to install due to different appearance, please refer to the
corresponding figures according to the actualproducts.
Manual Vari-focal Camera
Figure 2-1

5
Important
Before installing the camera, please make sure the installation surface can support at least 3x
the weight of the camera and the bracket.
Follow the steps listed below to install the camera. Please refer to Figure 2-1 forreference.
Step 1
Use the included hex wrench to open dome enclosure by loosening the 3 hex screws on the exterior
of the camera’s dome.
Step 2
Locate the mounting template sticker and affix it on the ceiling or the wall according to your monitor
area requirements.
Step 3
Drill 3 holes, 3/16” diameter as indicated at the marks on the template. Remove the template and
insert the 3 included plastic expansion anchors in the holes.
Note:
If the cable must exit behind the installationsurface (behind a wall or inside the ceiling), Drill a
¾” cable exit hole in the mounting surface according to the installation template.
If the cable must exit the camera on the surface of the wall or ceiling, use a strong needle-nose
plier or similar tool to pry out and remove the thin metal of the camera’s outer shell, as shown in
Figure 2-1 above; “Remove this for surface-cable use”.
Step 4
Adjust the base of the camera to the proper position and then pull the cable through the cable exit
hole drilled earlier in the ceiling or wall. Line up the TOP direction of the device to the installation
template and then line up the three screw holes in the camera’s base to the three plastic anchors in
the mounting surface. Install the three self-tapping screws firmly into the anchors.
Step 5
Loosen the two thumb screws which secure the lens rotation structure NOTE: Do not remove these
screws. Only loosen them enough for the camera housing to move freely to the correct
viewing position. Adjust the lens to the required viewing angle, then secure the screws of the lens
rotation structure. The lens adjust angle ranges are: flip (0°~+75°), video pan rotation (-15°~+15°),
video rotation angle(-15°~+15°).
Note:
Pay attention to the image rotation direction when aiming the camera vertically past 64 degrees
vertically, to avoid the outer cover blocking the IR light and influencing the IR effect.

6
Figure 2-2
Note:
If the camera needs to be restored to factorysettings, long press the “Reset” button shown in
Figure 2-2 for 10 seconds while the camera is powered on
If the camera needs to use the WPS function, short press the “Reset” button shown in Figure 2-
2 for 1~2 seconds when the camera is powered on, then press the WPS button of the router,
generally the camera can be connected to the corresponding router within 1 minute (only
supported by somemodels).
Step 6
Reconnect the camera dome cover to the camera properly,taking care to align the screws with
the corresponding holes, and fasten the three hex screws with the included hex wrench. The
camera installation isnowcomplete.
2.2 Micro SD Card Installation
Note:
This model of camera does not support Micro SD card functions.
Shut down the power and turn off the camera before you install the Micro SDcard.
Step 1 Find the Micro SD Card slot in figure 2-3, open the Micro SD Card slot according to the
direction shown in figure 2-4.
Step 2 Orient the Micro SD Card to the proper direction and install it in the Micro SD cardslot.
Step 3 According to the direction shown in figure 2-4, close the Micro SD card slot and keep itlocked.

7
Figure 2-3 Micro SD Card installation illustration1
Figure 2-4 Micro SD Card installation illustration2
2.3 Lens Adjustment
Step 1
Loosen adjustment screw C slightly, and then move the threaded rod of adjustment screw C slightly to
rotate the lens barrel it is connected to. Adjust the lens focal length to the needed position according to
the image display.
Step 2
Loosen the adjustment screw D slightly, and then move the threaded rod of adjustment screw D
slightly to rotate the lens barrel it is connected to. Make the lens focus clear according to the image
display, then tighten the adjusting screw D.
Step 3
The image may become blurry during the process of tightening adjusting screw D, adjust the image
slightly by moving adjusting screw C, then adjust the image to become clear and finally tighten the
screw C.
Note:
The dome housing must be positioned properly and all rubber seals must be in place to ensure
the camera’s waterproof function. Be sure to reassemble the camera carefully after making
an adjustment.
Figure 2-5

8
3 Network Configuration
The IP address of each camera is the same when leaving the SecurityTronix factory (default
IP192.168.1.108). For the smoothest project installation, please allocate a useable IP segment of
the entire network according to the actual networkenvironment.
3.1 Modify IP Address
IP address can be acquired and modified through the quick configuration tool for the cameras which is
accessed via a wired network; Cameras must connect via a wired network to configure wireless
parameters before using wireless network cameras. This chapter will introduce the approach of
modifying IP addresses via the “Quick Configuration Tool”. You can also modify the IP address in the
network parameters of the WEB interface. Please refer to the document in the disk << WEB Operation
Manual>> for more details.
NOTE:
Currently the quick configuration tool only supports cameras which are addressed within the same
network segment (subnet) as the computer’s IP address.
Step 1 Double click the “ConfigTools.exe” and open the quick configuration tool.
Step 2 Double click the device to be configured, and the “Login” dialog box will appear. Enter the IP
address, user name, password and port number of the camera, and click “Confirm”.
NOTE:
The default user name and password are admin and admin respectively. The default portnumberis
37777. See Figure 3-1 for more details.

9
Figure 3-1
Step 3 Modify the camera IP address on the “Net” interface, click “Save” to finish modification.
See Figure 3-2 for more details.
3.2 Login WEB Interface
Figure 3-2
Note:
Different devices may have different WEB interfaces, the figures below are just for reference, please
refer to the document <<WEB Operation Manual>> in the disk and the actual interface for more details
Step 1 Open IE and input the modified camera IP address in the addressbar.
Step 2 The login interface is shown below, please input your user name and password (Default user
name is admin and password is admin respectively), click“login”.
See Figure 3-3 for more details.

10
Figure 3-3
Step 3 Install controls according to the system prompt; see Figure 3-4 for the WEB main interface.
Modify the administrator password as soon as possible after you have successfully loggedin.
Figure 3-4

11
Note
•This quick start guide is for reference only. Slight difference may be found in the user
interface.
•All the designs and software here are subject to change without prior written notice.
•Please visit our website or contact your local service engineer for more information.
SecurityTronix offers live, human tech support for our products 24 hours a day, 7 days a week, 365
days a year.
Technical support contact info:
Phone: [phone] Option #3, then #2
Email: [e-mail]
Web: www.securitytronix.com/support
SecurityTronix
1085 Andrew Dr. Ste A
West Chester, PA 19380