Securitytronix ST-D600IRVP2812 User manual

1.0 1/10/11
1
INSTALLATION MANUAL
ST-D600IRVP2812
Super WDR, 3D DNR True Day & Night
Infrared Vandal Proof Dome Camera

1.0 1/10/11
2
PACKAGE CONTENTS
This package contains:
One ST-D600IRVP2812 Super WDR infrared vandal proof dome color camera
One installation manual
Note: The ST-D600IRVP2812 requires a minimum 12VDC 590mA power supply such as the
ST-PS12VDC1A or ST-PS12VDC2A. The camera may also operate at 24VAC 250mA.
PRODUCT DESCRIPTION
The ST-D600IRVP 2812 is a professional grade, vandal proof WDR (Wide Dynamic Range) day
and night infrared color dome camera designed to provide clear images even under intense back
light conditions. The camera uses a 1/3” SONY Color Vertical Double Density CCD, provides
600TV lines of resolution in color and 700TV lines in B&W. The ST-D600IRVP2812 has a 2.8mm –
12mm lens for wide or narrow viewing. The 3 axis mount, built-in RS485 connection and
on-screen display make this camera very easy to set up. The 30 infrared LEDs support low light
illumination down to 0.0008Lux. This is a dual voltage camera that can be powered with either
12VDC or 24VAC.
SPECIFICATIONS
ST-D600IRVP2812
Specifications (Typical)
1. Image Sensor
1/3” SONY Color Vertical Double Density CCD
2. Scanning System
NTSC
3. Horizontal Resolution
600TV Lines Color, 700TV Lines B&W
4. Synchronization
Internal H/V 15.734/59.94Hz
Line Lock H/V 15.750/60Hz
5. Minimum Illumination
Sens-Up Off 0.12Lux (15IRE), 0.2Lux (30IRE),
0.4Lux (50IRE) F1.2
Sens-Up On 0.0002Lux (15IRE), 0.0005Lux
(30IRE), 0.0008Lux (50IRE) F1.2
6. Scanning System
2 :1 interface
7. Auto Electronic Shutter
1/60s~1/100,000s
8. Auto Gain Control
Automatic
9. Lens
Aspherical 2.8 –12mm DC Auto Iris ICR lens
10. S/N Ratio
>52dB (AGC off)
11. Privacy Masking
8 Windows (Polygonal, 8 Colors)
12. Day & Night
Color, B&W, Auto, Ext
13. IR LED
30 units 850nm infrared LEDs, 20,000 hrs.
14. IR Beam Spread
36° -56°
15. Night View Distance
Indoor 115 feet, Outdoor 80 feet
16. Motion Detection
On/Off
17. Digital Zoom
X1.0 –x10
18. Gamma Correction
0.45
19. Video Output
1.0Vp-p/75Ω
20. WDR Level
120dB Max.
21. Operating Temperature
-4F°- 140°F
22. Operating Humidity
30% -80%
23. Power Supply
DC12V 540mA, DC12V 590mA/AC24V 250mA
24. Dimensions
5.7”x4.2”
22. Weight
2.5 lbs

1.0 1/10/11
3
INSTALLATION AND OPERATION
CAUTION: To reduce the risk of electrical shock do not remove the cover or back of this
unit. No user serviceable parts are inside.
CAUTION: To prevent electric shocks and risk of fire hazards, do not use other than
specified power source.
1. UNPACKING and HANDLING
Each unit is shipped assembled and factory tested.
Ensure that all accessories are removed from the container before discarding packing material
2. MECHANICAL INSPECTION
Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is
clean, and no connectors are broken, damaged, or loose. If equipment appears to be
damaged or defective please contact your distributor or SecurityTronix at 1-610-429-1511 for
assistance.
3. SPECIAL ATTENTION
a. The installer must comply with electrical safety standards. There must be sufficient
space between the camera’s power supply and video line and any high voltage
equipment and/or cables.
b. To help ensure the camera’s life and proper operation do not point the camera
towards the sun or strong light.
c. Do not install the camera in an environment where the temperature is above 140°F.
d. Do not install the camera near a magnetic field or a high-power motor.
e. Do not mount the camera near a radiator or heater.
f. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe
gently with a mild detergent. Never use strong or abrasive detergents.
g. Using a power supply other than specified will damage the camera.
h. Only qualified installers are allowed to install, test and disassemble the camera.
i. The camera is a low voltage product. If installed outdoors proper safety and lightening
grounding are required.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions.
This symbol is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electrical shock.

1.0 1/10/11
4
4. WIRING CONNECTIONS
a. Connect the power supply’s DC plug to the camera’s power outlet.
b. Connect the camera to the monitor with a 75Ωcoaxial video cable.
c. Connect power supply’s AC plug to a suitable AC power outlet.
d. Adjust the lens direction according to the required surveillance area and environment.

1.0 1/10/11
5
5. OSD SETTINGS
Accessing and setting the camera functions are done through the camera’s On Screen Display
(OSD) via the mini-joystick on the unit’s circuit board. A menu item may be selected my moving
the joystick UP, DOWN, LEFT or RIGHT. The selected item may be entered by taping the joystick.
OSD SETTINGS
UP
DOWN
LEFT
RIGHT

1.0 1/10/11
6
6. WIDE DYNAMIC RANGE
Wide Dynamic Range (WDR) allows the capturing of images at all light levels. The camera offers
10 WDR levels selectable through the settings menu.
WDR Low Level (0 –3): WDR mode for general or low light conditions.
WDR Middle Level (4 –7): WDR mode for medium light conditions.
WDR High Level (8 –10): WDR mode for strong or bright light conditions.
Factory default is WDR Low Level 0 with the WDR mode set to ON.
The ECLIPSE function is used to recognize detail under strong light conditions (e.g., to recognize
a vehicle license plate number when the ambient light is stronger than the vehicle’s headlight).
Note the ECLISPE mode should be off while using the WDR ON.

1.0 1/10/11
7
7. TROUBLESHOOTING
a. No picture after applying power –(i) check all plugs and cables are securely
connected to the proper connectors; (ii) ensure your power supply is providing the
correct voltage and current.
b. The picture has ripples –(i) check to see if the power supply is experiencing AC ripple,
if so a filter may be required; (ii) determine if the monitor is faulty; (iii) determine if
other peripheral equipment is causing ripple and if so make the necessary
adjustments.
c. The picture background continuously changes color –a fluorescent lamp’s magnetic
field may cause color roll, therefore, reduce the number of fluorescent lamps or
increase the distance between the camera and the lamps.
d. The picture appears smeared –(i) the power supply voltage level may be unstable,
therefore, try another power supply; (ii) ensure the cables are correctly connected
and/or the cables are of the correct impedance.
e. Other interference may require a SecurityTronix ground loop isolation filter.
f. Additional troubleshooting assistance can be found on-line at www.securitytronix.com
in addition to support from SecurityTronix sales engineers at 1-610-429-1511.