Securitytronix ST-IP4VFB-MZ User manual

ST-IP4VFB-MZ
QUICK START
GUIDE
www.securitytronix.comwww.nacebrands.com

ST-IP4VFB-MZ QUICK START GUIDE
1
1
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
About This Document
This manual applies to the smart bullet cameras.
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We will
readily improve or update the products or procedures described in
the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of this
product. UL has only tested for fire, shock or casualty hazards as
outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or
signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING
RELATED FUNCTIONS OF THIS PRODUCT.

ST-IP4VFB-MZ QUICK START GUIDE
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at their
own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the
EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.

ST-IP4VFB-MZ QUICK START GUIDE
3
3
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal
waste in the European Union. See the product
documentation for specific battery information.
The battery is marked with this symbol, which
may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info

ST-IP4VFB-MZ QUICK START GUIDE
4
4
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
● While using this product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
● Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

ST-IP4VFB-MZ QUICK START GUIDE
5
5
● Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
● Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
● If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
technical support.
Cautions
● Make sure the power supply voltage is correct before using the
camera.
● Do not drop the camera or subject it to physical shock.
● Do not touch sensor modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
● Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
● The sensor may be burned out by a laser beam, so when any
laser equipment is in use, make sure that the surface of sensor
will not be exposed to the laser beam.

ST-IP4VFB-MZ QUICK START GUIDE
6
6
● Do not place the camera in extremely hot, cold (the operating
temperature shall be-22F~+140F,or -40°F ~ 140°F if the camera
model has an “H” in its suffix), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
● To avoid heat accumulation, good ventilation is required for
optimal operation.
● Keep the camera away from liquid while in use.
● While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
● Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average life span. The average time varies
because of differences between operating environment and
usage.
●Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
● If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (Securitytronix shall not
assume any responsibility for problems caused by unauthorized
repair or maintenance.)

ST-IP4VFB-MZ QUICK START GUIDE
7
7
Table of Contents
1 Appearance Description ................................................................. 8
1.1 Camera Description ......................................................... 8
1.2 Wiring ............................................................................. 9
2 Installation .................................................................................... 11
3 Setting the Network Camera over the LAN .................................. 18
4 Accessing via Web Browser .......................................................... 24

ST-IP4VFB-MZ QUICK START GUIDE
8
8
1Appearance Description
Camera Description 1.1
The overview of the network bullet camera is shown below:
Overview Figure 1-1
Description Table 1-1
No.
Description
No.
Description
1
Sun Shield
2
Bracket
1
2
3
654
7

ST-IP4VFB-MZ QUICK START GUIDE
9
9
No.
Description
No.
Description
3
Junction Box
4
Reset
5
SD Card Slot
6
Front Box
7
Analog Video Output
Wiring 1.2
The wiring varies according to the different models of bullet camera.
Wiring (A) Figure 1-2
Description (A) Table 1-2
No.
Description
1
Power supply interface
2
10M/100M self-adaptive Ethernet interface
1
2
-+
DC12V

ST-IP4VFB-MZ QUICK START GUIDE
10
10
Wiring (B) Figure 1-3
Description (B) Table 1-3
No.
Description
1
AUDIO IN, G: Audio input interface
2
AUDIO OUT, G: Audio output interface
3
IN, G: Alarm input interface
1A, 1B: Alarm output interface
4
D+, D-: RS-485 interface
5
Power supply interface
6
10M/100M self-adaptive Ethernet interface
2
1
3
4
5
6
AUDIOOUT
AUDIOIN
DC12V
+ -
RS485
D-D+

ST-IP4VFB-MZ QUICK START GUIDE
11
11
2Installation
Before you start:
Make sure the device in the package is in good condition and all
the assembly parts are included.
Make sure all the related equipment is powered-off during
installation.
Check the specification of the products for the installation
environment.
Make sure the power supply is matched with your required
voltage to avoid damage.
If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
Make sure that the wall is strong enough to withstand three
times the weight of the camera.
For the cameras that supports IR, you are required to pay attention
to the following precautions to prevent IR reflection:
● Dust or grease on the dome cover will cause IR reflection.
Please do not remove the dome cover film until the installation
is completed. If there is dust or grease on the dome cover,
clean the dome cover with clean soft cloth and isopropyl
alcohol.

ST-IP4VFB-MZ QUICK START GUIDE
12
12
● Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing poor image quality.
● The foam ring around the lens must be seated flush against the
inner surface of the bubble to isolate the lens from the IR LEDS.
Fasten the dome cover to camera body so that the foam ring
and the dome cover are attached seamlessly.
Steps:
1. Drill four screw holes in the wall according to the No.2 holes of
the supplied drill template.
Drill Template Figure 2-1
2. Drill one cable hole according to the drill template.
If you want to route the cables through the side of the junction box,
you can skip this step.
Cable Hole
11
11
2
22
2

ST-IP4VFB-MZ QUICK START GUIDE
13
13
3. Fix the junction box to the wall with the expansion screws.
Install the Junction Box Figure 2-2
4. Route the cables of the camera.
Route the cables through the junction box and the cable hole if
there is a cable hole drilled on the ceiling.
Route the cables through the side outlet of the junction box to
the surface of the ceiling if there is no cable hole drilled on the
ceiling.
Junction Box

ST-IP4VFB-MZ QUICK START GUIDE
14
14
5. Hook the camera to the junction box with the safety rope.
6. Tighten the screws to fix the camera to the junction box.
Fix the Camera to the Junction Box Figure 2-3
7. Loosen the screws on the bracket to adjust the camera to the
desired surveillance angle and then tighten the screws to fix the
camera.
Safety Rope

ST-IP4VFB-MZ QUICK START GUIDE
15
15
Adjust Monitoring Angle Figure 2-4
Please loosen the screws slightly until you can adjust the camera
and do not remove the screws from the bracket.
8. Loosen the lock screw on the sun shield and remove the sun
shield.
9. Rotate to remove the front box from camera and adjust the
zoom lever and focus lever to get a clear image.
Tilt Adjust Nut
Pan Adjust Nut

ST-IP4VFB-MZ QUICK START GUIDE
16
16
Lens Adjustment Figure 2-5
For devices supporting motorized zoom lens (MZL), you can only
adjust the camera to the proper surveillance angle via 3-axis
adjustment, then adjust the zoom and focus by the PTZ control
from the client software or web browser.
10. Reinstall the front box and the sun shield to finish the
installation.
Zoom Lever
Focus Lever Remove the Sun Shield
Romove the Front Box

ST-IP4VFB-MZ QUICK START GUIDE
17
17
For projects with strict water-proofing demands, you may need to
install a water-proof rubber case (purchased separately) to ensure
a waterproof installation. See the figure below.
Install the Rubber Case Figure 2-6

ST-IP4VFB-MZ QUICK START GUIDE
18
18
3Setting the Network Camera over the
LAN
Purpose:
To view and configure the camera via LAN (Local Area Network),
you need to connect the network camera in the same subnet as
your PC. Then, install the SADP or client software to search and
change the IP of the network camera.
The following figure shows the cable connection of network
camera to PC:
Wiring over LAN Figure 3-1
Set the IP address of the camera for accessing via LAN.
Steps:
1. To get the IP address, you can choose either of the following
methods:
Use SADP, a software tool which can automatically detect
network cameras in the LAN and list the device information like
IP address, subnet mask, port number, device serial number,
device version, etc., shown in Figure 3-2.

ST-IP4VFB-MZ QUICK START GUIDE
19
19
Use client software to list the online devices. Please refer to the
user manual of client software for detailed information.
2. Change the IP address and subnet mask to the same subnet of
your PC.
Refer to the following introductions to set IP address with SADP
software:
Search active devices online
Search online devices automatically:
After launch the SADP software, it automatically searches the
online devices every 15 seconds from the subnet where your
computer locates. It displays the total number and
information of the searched devices in the Online Devices
interface. Device information including the device type, IP
address, port number, gateway, etc. will be displayed.