Securitytronix ST-IP2FWD User manual

ST-IP2FWD QUICK
START GUIDE
www.securitytronix.comwww.nacebrands.com

ST-IP2FWD QUICK START GUIDE
1
1
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
About This Document
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We will
readily improve or update the products or procedures described in
the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of this
product. UL has only tested for fire, shock or casualty hazards as
outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or
signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING
RELATED FUNCTIONS OF THIS PRODUCT.

ST-IP2FWD QUICK START GUIDE
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the
EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.

ST-IP2FWD QUICK START GUIDE
3
3
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information
see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info

ST-IP2FWD QUICK START GUIDE
4
4
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
●While using this product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
●Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

ST-IP2FWD QUICK START GUIDE
5
5
●Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
●Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
●If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
technical support.
Cautions
●Make sure the power supply voltage is correct before using the
camera.
●Do not drop the camera or subject it to physical shock.
●Do not touch sensor modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
●Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
●The sensor may be burned out by a laser beam, so when any
laser equipment is in use, make sure that the surface of sensor
will not be exposed to the laser beam.

ST-IP2FWD QUICK START GUIDE
6
6
●Do not place the camera in extremely hot, cold (the operating
temperature shall be-22F~+140F,or -40°F~ 140°Fif the camera
model has an “H” in its suffix), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
●To avoid heat accumulation, good ventilation is required for
optimal operation.
●Keep the camera away from liquid while in use.
●While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
●Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average life span. The average time varies
because of differences between operating environment and
usage.
●Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
●If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (Securitytronix shall not
assume any responsibility for problems caused by unauthorized
repair or maintenance.)

ST-IP2FWD QUICK START GUIDE
7
7
Table of Contents
1 Appearance Description ................................................................. 8
2 Installation .................................................................................... 11
2.1 Ceiling Mounting........................................................... 12
2.2 Ceiling Mounting with a Gang Box ................................ 17
2.3 Ceiling Bracket Mounting .............................................. 19
2.4 Wall Bracket Mounting.................................................. 21
2.5 Install the Micro SD Card ............................................... 24
3 Setting the Network Camera over the LAN .................................. 26
4 Accessing via Web Browser .......................................................... 31

ST-IP2FWD QUICK START GUIDE
8
8
1Appearance Description
Figure 1-1 Overview (1)
Figure 1-2 Overview (2)
8
4
2
1
3
7
6

ST-IP2FWD QUICK START GUIDE
9
9
Table 1-1 Physical Description
No.
Description
1
Front Cover
2
Dome Drive
3
Micro SD Card Slot
4
Network Cable
5
Lens
6
IR LED
7
Power Cable
8
Audio/Alarm Cables
9
Wi-FiAntenna (If equipped)
10
Serial Port Interface
11
Hex Screw
12
MIC
13
RESET/WPS Button
Press RESET about 10s when the camera is powering on or
rebooting to restore the default settings, including the user
name, password, IP address, port No., etc.

ST-IP2FWD QUICK START GUIDE
10
10
No.8 is the audio/alarm cable interface, of which the “I”mark
connects to the alarm input, the “o”mark connects to the
alarm output, the “GND”mark connects the grounding, and the
“A”mark connects the audio output.
WPS (Wi-Fi Protected Setup, also known as AOSS or QSS) is a
computing standard that attempts to allow easy establishment
of a secure wireless network. Refer to user manual for details.
A wireless router with the WPS function is required to enable
the WPS function of the camera. Refer the steps below.
Steps:
1. Press the WPS button on the router.
2. Press the WPS button (about 2s) on the camera within 120s
you enable the WPS of the router to join in the wireless
network.
The WPS button works as a reset button only when you
press it when the camera is powering on.
Press the WPS button on the camera, and then press the
WPS button on the router will establish a connection as
well, and the expiration time of WPS connection on the
camera is 120s.
The link indicator blinks if the wireless connection is
successful.

ST-IP2FWD QUICK START GUIDE
11
11
2Installation
Before you start:
Make sure the device in the package is in good condition and all the
assembly parts are included.
Make sure all the related equipment is power-off during
installation.
Check the specification of the products for the installation
environment.
Make sure the power supply is matched with your required voltage
to avoid damage.
If the product does not function properly, please contact your
dealer or technical support. Do not disassemble the camera for
repair or maintenance by yourself.
Make sure that the wall is strong enough to withstand three times
the weight of the camera.
For the camerasthat supports IR, you are required to pay attention
to the following precautions to prevent IR reflection:
●Dust or grease on the dome cover will cause IR reflection.
Please do not remove the dome cover film until the installation
is completed. If there is dust or grease on the dome cover,
clean the dome cover with clean soft cloth and isopropyl
alcohol.

ST-IP2FWD QUICK START GUIDE
12
12
●Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing poor image quality.
●The foam ring around the lens must be seated flush against the
inner surface of the bubble to isolate the lens from the IR LEDS.
Fasten the dome cover to camera body so that the foam ring
and the dome cover are attached seamlessly.
2.1 Ceiling Mounting
Steps:
1. Drill the screw holes and the cable hole in the ceiling according
to the supplied drill template.
Figure 2-1 Type I Drill Template
Drill Template
1
1
11
Hole A:for cables routed through the ceiling
Screw hole 1:for Mounting Base
FRONT

ST-IP2FWD QUICK START GUIDE
13
13
A different type of drill template might be provided because of the
different batches of products. Also, the contained adapter plate
matches with type II drill template may differs as well.
Figure 2-2 Type II Drill Template
2. Loosen the set screw on the front cover to disassemble the
camera with the supplied Allen key.
Figure 2-3 Disassemble the Camera
Drill Template
A
1 1
Hole A :for cables routed through the wall
Screw hole1 :for Mounting Base
FRONT
Code:194101278

ST-IP2FWD QUICK START GUIDE
14
14
3. Fix the adapter plate to the ceiling with the supplied expansion
screws.
Figure 2-4 Fix the Adapter Plate
If the supplied drill template is type II drill template, you can just skip
step 3 and go straight to step 4.
4. Fix the dome drive with the supplied screws.
Figure 2-5 Fix the Dome Drive
Adapter Plate
Side Outlet

ST-IP2FWD QUICK START GUIDE
15
15
5. Connect the power cable, network cable, and the audio/alarm
cables.
Use a plier to remove the removable tab and route the cables via side
outlet (as shown in Figure 2-4) if no cable hole is drilled in step 1, and
connect the corresponding cables.
Figure 2-6 Remove the Removable Part
6. View the image via the web browser.
7. Slightly loosen the hex screw beside the WPS/RESET button to
adjust the surveillance angle.
8. Use the supplied adjusting tool to adjust the pan [±30°], tilt
[0~80°], and rotation direction [0~360°].

ST-IP2FWD QUICK START GUIDE
16
16
Figure 2-7 3-Axis Adjustment
9. Tighten the hex screw to fix the well-adjusted surveillance angle.
10. Align the front cover to the dome drive and tighten the set
screws on the front cover.
Figure 2-8 Install the Front Cover
Adjusting Tool
Rotation
Tilt
Pan

ST-IP2FWD QUICK START GUIDE
17
17
11. Tear off the protection film softly to complete the installation.
Do not tear off the protection film until the installation is
completed.
Do not touch the inside face of the bubble with your hands.
2.2 Ceiling Mounting with a Gang Box
Steps:
1. Fix the adapter plate to the gang box with the supplied PM4X8
screws.
Figure 2-9 Fix the Adapter Plate
2. Fix the dome drive to the adapter plate with the supplied PM4X8
screws.

ST-IP2FWD QUICK START GUIDE
18
18
Figure 2-10 Fix the Dome Drive
3. Connect the power cable, network cable, and the alarm/audio
cables.
4. Align the front cover to the dome drive and tighten the set
screws on the front cover.
Figure 2-11 Install the Front Cover

ST-IP2FWD QUICK START GUIDE
19
19
5. Tear off the protection film softly to complete the installation.
Do not tear off the protection film until the installation is
completed.
Do not touch the inside face of the bubble with your hands.
2.3 Ceiling Bracket Mounting
Steps:
1. Install the bracket to the ceiling with the supplied screws in the
ceiling bracket package.
You need to purchases the matched ceiling bracket model separately
if ceiling bracket mounting is adopted.
2. Fix the adapter plate to the ceiling bracket with the supplied
PM4X8 screws.