ENFORCER EV-Y1201-A2WQ User manual

4-in-1 HD TVI, CVI, AHD, Analog
Bullet Cameras
Manual
•Select between multiple formats:
TVI, CVI, AHD, and Analog
•
1080p Resolution
•
ICR Module
•
Joystick OSD Control
•3D-NR (3D Digital Noise Reduction)
•
DWDR (Digital Wide Dynamic Range)
•
Rugged, weatherproof (IP66) construction
•
Cables concealed in bracket to
prevent tampering
Features:
Model #
Lens
Resolution
Voltage
Style
Color
EV-Y1201-A2WQ
2.8mm
1080p
12VDC
Bullet
White
EV-Y1201-AMWQ
2.8~12mm
1080p
12VDC
Bullet
White
EV-Y1201-AMWQ shown

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras
2SECO-LARM U.S.A., Inc.
Specifications:
Model
EV-Y1201-A2WQ
EV-Y1201-AMWQ
Type
Fixed Bullet Camera
VarifocalBullet Camera
Formats
TVI (Default) / CVI / AHD / Analog
CMOS
1/2.9" 2MP Sony CMOS
Resolution (HD)
1920x1080
TV Lines (Analog)
1200TVL
3D-NR
Yes
2D-NR
Yes
DWDR
Yes
OSD (On-Screen Display)
Yes
Cable OSD control
Yes
Videooutput
1.0Vp-p Complexvideo output
Megapixels
2MP
Lens
2.8mm ICR
2.8~12mm ICR
Viewing angle
90°
30°~90°
# of IR LEDs
30
3 (IR III)
IR Range
Up to 50ft (15m)
Up to 100ft (30m)
FPS
30FPS
F Stop
F1.4-F1.6
Minimum illumination (IR On)
0Lux
Gamma correction
0-1
S/N Ratio
50dB
DSS (DigitalShow Shutter)
Yes
Shutter control
Yes
Gain control
Yes
Whitebalance
Auto, Day & Night
Operating voltage
12VDC
Current draw
(IR On)
160mA
400mA
(IR Off)
90mA
90mA
IP Rating
IP66
Operating temperature
-4°~131° F (-20°~55° C)
Dimensions
6
9
/16"x2
9
/16" (166x65 mm)
10
7
/16"x3
1
/4" (265x83 mm)
Weight
14.1-oz (400g)
1-lb 10.8-oz(760g)
Dimensions:
1x
Bullet camera
3x/4x*
Screws
3x/4x*
Screw anchors
1x
DC plug with terminal block
1x
Hexwrench
1x
Flathead screwdriver*
1x
Mounting template
1x
Manual
Parts List:
* EV-Y1201-AMWQ Only
EV-Y1201-AMWQ:
EV-Y1201-A2WQ:
415/16" (126mm)
215/
16
"
(75mm)
69/16" (166mm)
29/
16
"
(65mm)
31/
4
"
(83mm)
107/16" (265mm)
65/8" (168mm)

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras
SECO-LARM U.S.A., Inc. 3
Overview:
Installation:
Important:Do not cut any wires as the warranty willbe voided.
1. Run a12VDC power supply wire and a video cable
with a male BNC connector to the wallor ceiling
where the camera isto be mounted.
2. Temporarily connect the camera to the 12VDC
power supply.
3. Temporarily connect the camera’s female BNC
connector to the video cable’smale BNCconnector.
4. While watching the monitor, hold the camera against
the wall or ceiling by hand where it isto be mounted,
then turn the camera until it is certain thatthis
mounting location is correct.
5. Adjust the zoom and focus to desired settings. See
"Zoom and Focus Adjustment*". (EV-Y1201-AMWQ
only).
6. Use the OSD controller's joystickto adjustthe camera
settings. See "OSD Controller Settings". (For more
information, see separate OSD manual).
7. Use a pencil and the included mounting template
sticker to mark the mounting location. Disconnect the
12VDC powersupplyand video cable.
8. Mountthe camera mountingbase to the wall using the
included mounting screws.
OSD Controller Settings:
To setformatvia the OSD controller, press the
controller in the direction of the desired setting,
hold for 5 seconds,and release when the
camera restarts.
See chart below.
Direction
Format Setting
Up
CVI
Down
TVI
Left
CVBS
Right
AHD
UP
DC Plugwith
terminal block
DC Jack
Female BNC
Connector
OSD controller
Sunshield screw
Sunshield
Zoom/Focuscompartment
Mounting arm
adjustment screw
Camera angle
adjustment screw
Mounting
screws
EV-Y1201-AMWQ shown above.
Zoom & Focus Adjustment*:
To adjust the Zoom and Focus, open the Zoom/Focuscompartment
using the providedhex wrench.
Oncewithin the compartment, use the provided flathead screwdriver
to loosen the Zoom and Focus screws to allow for adjustment.
Focus
To focus in on close objects, push
the focus screw right towards "N".
To focus out on far objects,push
the screw right towards "F".
Zoom
To zoom in, push the zoom screw
left towards "T". To zoom out, push the
screw right towards "W".
1. Use the camera within the given temperature
and voltage limits.
2. Donot point the cameraat the sun.
3. Do notsubject the camera to strong vibrations.
4. Do notmountthe camera in areas exposed to radiation,
strong magneticfields, or strong electricalsignals.
Before Starting:
Mounting base
*EV-Y1201-AMWQ only.
To adjust the cameraangleand positioning,
loosen the cameraangle adjustment screw
and mounting arm adjustment screw.
Rotate the cameraand position the
mounting arm in the desired position and
retighten the screws.
Camera arm position:
Camera Angle and Positioning:
Mounting arm
adjustment screw
Camera angle:
Camera angle
adjustment screw
(Continued nextpage)
Zoom
Focus

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras
4SECO-LARM U.S.A., Inc.
The screen is blank.
•Check that the camera is powered up.
•Check that the power supply's polarity is correct.
•Check that the monitor is powered up.
•Check that the video cable connecting the camera to the monitor is
connected properly.
The screen image is dim.
•Clean the lens using a soft, clean cloth.
•Check that the light source is adequate.
The screen image has poor contrast.
•Adjust the monitor's contrast knob.
•Change the position of the camera.
The screen image flickers.
•Change the position of the camera, check cables and format setting
The screen image is distorted.
•Change the position of the camera, check cables and format setting
The camera case is hot.
•Check that the correct power supply is in use.
Installation (continued):
®
PICSN4
MI_EV-Y1201-AxWQ_161026.docx
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM
will not be
held responsible for the use of this product in violation of any current lawsor statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE
MUST ACCEPT
ANY INTERFERENCE RECEIVED,INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changesor modifications not expressly approved by the partyresponsible forcompliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void user’s authority to operate thedevice.
SECO-LARM
®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: [phone] | [phone]
Email: [e-mail]
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints.
Copyright © 2016SECO-
LARM U.S.A., Inc. All rights reserved. This material maynot be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for three (3) years from the date of sale to the original customer.SECO-LARM’s obligation is limited to
the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration
,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM
’s
option. In no event shall SECO-
LARM be liable forany special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
Troubleshooting:
WARNING: Stop using the camera if yousee a malfunction such as smoke or unusual heat, asit could cause fire or electric
shock.
Do not open the case of this device,as there are nouser-serviceable components inside.
Do not cut
any wires as thewarranty will be voided.
9. Reconnect the12VDC power supply and video cable.
10.
Turn the monitor on and confirm the camera is sending the proper video signal.
11.
Adjust the camera to the desired angle and position. See "Camera Angle and Positioning" for more information.
12. Do a final test of the video camera and monitor.