Securitytronix ST-PTZIR650-23 User manual

INSTALLATION MANUAL
ST-PTZIR650-23
High Speed Intelligent Dome
PTZ Color Camera

Copyright North American Cable Equipment,
WARNINGS AND CAUTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS
THROUGH VENTILATION GRILLS OR OPENINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user the presence of non-insulated “dangerous voltage” within the product’s
enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to
different persons.
The exclamation point within an equilateral triangle, is intended to alert the user the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying this product.

PRECAUTIONS:
Persons without technical qualifications should not attempt to operate this
dome device before reading this manual thoroughly.
Remove any power to the dome before attempting any operations or adjustments
inside the dome cover to avoid potential damage to the mechanism.
Inside the dome cover there are precision optical and electrical devices.
Heavy pressure, shock and other sudden adjustments or operations should be
avoided. Otherwise, you may cause irreparable damage to the product.
Please DO NOT remove or disassemble any internal parts of the video camera to
Avoid normal operation and possibly void the warranty. There are no serviceable
parts inside the camera.
All electrical connections to the dome should be made in strict accordance with the
attached labels and wiring instructions in this manual and in accordance with all
local and national electrical codes. Failure to do so may damage the dome
beyond repair and void the warranty.
For outdoor installation especially in high places or poles, it is highly recommended
that the proper lightning arrestors and surge suppressors are installed before the
dome is entered into service.
Please do not use the product under circumstances where the environment
exceeds the maximum specified temperature, humidity or power supply
specifications.

1
IMPORTANT SAFEGUARDS
1. Read these instructions before attempting installation or operation of this dome.
2. Keep these instructions for future reference.
3. Heed all warnings and adhere to electrical specifications. Follow all instructions.
4. Clean only with non abrasive dry cotton cloth, lint free and approved acrylic cleaners.
5. Should the clear dome of the camera become dirty, use a special lens cleaning cloth and
solution to properly clean it.
6. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.
7. Use only attachments or accessories specified by the manufacturer.
8. Verify that the surface you are planning to use for attaching the dome can adequately support
the weight of the device and mounting hardware.
9. Protect this device against lighting storms with proper power supplies, surge arrestors and
other protective precautions.
10. Refer all servicing to SecurityTronix service personnel. Servicing is required when the
device has been damaged in any way, when liquid traces are present, or the presence of loose
objects is evident or if the device does not function properly, or has received sever impact or
has been dropped accidentally.
11. Do not use this product under circumstances exceeding specified temperature and humidity
ratings.
12. Avoid pointing the camera directly to the sun or other extremely bright objects for prolonged
period of time avoiding the risk of permanent damages to the imaging sensor.
13. The attached instructions are for use by qualified personnel only. To reduce the risks of
electric shock, do not perform any servicing other than contained in the operating instructions
unless you are qualified to do so.
14. During usage, the user should abide by all electrical safety standards and adhere to
electrical specifications for the operation of the dome. The control cable for RS485
communications as well as the video signal cables should be isolated from high voltage
equipment and high voltage cables.
15. Use supplied power supply transformer only.

2
1 Product Contents
IR Speed dome 1pc
Wall mount bracket 1pc
Power supply 1pc
Screws kit 1pc
User manual 1pc

3
1.2 Specification
Horizontal Rotation
Speed
0.02°-200°/s
Tilt Rotation Speed
0.02°-100°/s
Horizontal Rotation
Range
360°
Tilt Rotation Range
93°
Auto Flip
Horizontal 180°, Vertical 90°
Auto control IR LED
PWM
A-B Scan
User programmable
A-B Scan Speed
1-64 levels setting available
360° Scan Speed
1-64 levels setting available
Dwell Preset
5-60s interval
Preset Points
220
Go to Preset Speed
200°/s
Guard Tours
4 groups
Guard Points per tour
Max.16 points, dwell time user selectable
Pattern Scan
4 pcs
Pattern Scan Record
max.15 minutes or 512 commands
Home Pos Time
1-60mins available
PWR on Action
Memory as power off / Pattern / 360° scan / A-B scan / Preset
cruise / Preset 1-8 / No action
Communication
Protocol
Pelco-D,Pelco-P
Communication
RS485 Bus
Baud Rate
1200/2400/4800/9600bps
Privacy Mask
Not supported on this module
3D Location
supported
Time Scheduling
function
Not supported on this module
Alarm
Optional
Auto-tracking
Optional
Operating
Temperature
Outdoor: -10°F ~ +130°F
Operating humidity
≤95% Non Condensing
Heater & Blower
Auto temperature control
Power
24VAC ≤3A
Lightning protection
transient voltage 6000V
IR Illumination
Distance
375 ft
Power Consumption
≤ 20W
Compatible camara
SONY,HITACHI, SAMSUNG etc.
LED Angle of
Illumination
Ø22=6,Ø16=5

4
1.3 Performance Features
PWM function. Intelligent IR illumination & power consumption is variable, dependent
upon the zoom factor.
3D allocation. The pan and zoom functions are performed simultaneously for faster
target acquisition.
Supported Protocols. Pelco-D/P; Others on special request.
4 path patterns. Each path can record 512 different instructions or 900s of
PTZ instructions.
Manual speed control.At the lowest 0.02º/s speed, the dome provides very
smooth operation .
4 guard groups. Up to 16 preset points can be assigned in each tour. Each of
the 16 points can be adjusted independently for dwell time and travel speed.
Optional IP module (built in provision).
Built-in high density RTC clock supports time management function.
Strong video processing ability supports auto-tracking and motion detecting
alarm function.
Park action. If the user does not operate the dome in a predetermined time, it will
automatically run a preset guard group, trace memory group, pan scan etc.
The dome can remember its current operation before being powered off and return
to its previous operation after power is restored.
Built-in fan and heater can control the temperature automatically.
Heater operates below 32°F and fan operates above 104°F.
Multiple languages for OSD menu, English, Spanish, Chinese etc.
The response of IR illumination to ambient light can be adjustable.
Accurate step motor control provides for stable running, precise location
and sensitive response.
Metal body construction with an environmental rating of IP 66.
Built-in 6000V anti-surge protection equipment.

5
1.4 Function Description
Auto-adaptive to Protocol and Module
The dome can auto-adapt to multiple protocols and many camera modules without changing
the DIP switchs.
3D Allocation
Allow the camera to operate both the pan and tilt simultaneously while recalling presets, for
faster operation.
Privacy Masking (Not available on this module)
This feature allows the user to set certain areas of the image as un-viewable, such as
manager’s computers, restrooms, etc.
Pattern
Records the user’s operation of the PTZ controls and plays them back exactly as they were
originally performed. Rather than a tour, where the camera moves single point to single point,
the movement of a pattern follows all the nuance of the operator’s input.
This dome camera has 4 path patterns. Each path can record 512 different instructions or the
longest 15mins of path operation, whichever is less.
Zero Alignment
The user can specify a pan-position point to be the camera’s “zero point”. When the dome is in
use, preset drift can occur over time. If this happens, the zero-point can be used as a reference
for the dome to reset its alignment.
Auto Flip
In the manual tracking mode, when a target goes directly beneath the dome, the dome will
automatically rotate 180 degree in horizontal direction to maintain continuity of tracking. When
the dome flips, the camera starts moving upward as long as you hold the joystick in the down
position.
Focus
The auto focus feature enables the camera to focus automatically to maintain clear image. The
user can also use manual focus when conditions require it, such as when there are near and far
objects in the frame at the same time.
Under the following conditions, the camera may not auto focus on the target:
(1) The target is not in the center of the screen;
(2) Attempting to view 2 subjects which are far and near at the same time;
(3) The target is a brightly lit object, such as a neon lamp, etc.;.
(4) The camera’s dome is covered with water droplets or dust;
(5) Targets are moving quickly;
(6) Large area targets without much detail, such as wall;
(7) Targets which are too dark or faint.

6
BLC Back Light Compensation (Not available on this model)
If a bright backlight is present, the target in the picture may appear dark or as a silhouette. The
BLC function can enhance the target in the center of the picture; the dome uses the center of
the picture to adjust the iris. If there is a bright light source outside this area which tends to
wash out to white, the camera will adjust the iris so that the target in the sensitive area will be
properly exposed.
Iris Control
The camera features automatic camera aperture (iris). The camera senses changes in ambient
light and automatically adjusts the lens aperture to make the brightness of the output image
stable.
Ratio Speed
Intelligent pan and tilt speed is variable dependent on the zoom factor. When zooming in, the
speed will become slower and when zooming out, the speed will become faster.
Pan Scan
The dome continuously scans 360°clockwise at set speed in horizontal direction, under the
condition that the pitch angle remains the same. While scanning, the operator can move the
joystick to exit from the scanning mode.
Preset
Once the camera has been programmed with specific location presets, it can automatically
move to the predefined positions when presets are called from a PTZ controller or DVR.
Guard Tour Scan
The dome runs a patrol according to the specific presets which the user has programmed, in
the order they are set to run.
A-B Scan
The dome scans back and forth between 2 preset points ( A-B points) in both horizontal and
vertical directions, according to the speed the user sets in the menu.
Power Off Memory
This feature allows the dome to resume its previous preset or status after power is restored. By
the default setting, the dome supports power up memory, which improves reliability and avoids
repeated settings of the previous parameters.
Park Action
If the dome is not operated within the user-set time, it will automatically run a specific mode
(pan scan, A-B scan, park action, cruise, preserve action etc.).
Multilanguage OSD Menu
The language used for the on screen menu can be set to one of several available languages -
English, Spanish etc.

7
2 Installation
2.1 DIP Switch Settings
2.1.1 Preparation
Before installation, make sure that the protocol, baud rate and address code used by the
product is fully consistent with the control system. Corresponding DIP switch settings can be
seen below. The access plate for the DIP switches is located just above the camera lens
opening on the outside of the camera:
NOTE:
It is much easier to set the communication parameters using the on-screen menu rather
than the DIP switches. See page 11 for details.
2.1.2 Address Settings
DIP switch SW1 is used to set the address of the camera. It is an 8-bit switch. The number
value of switch 1 = 1, switch 2 = 2, switch 3 = 4, switch 4 = 8, switch 5 = 16, switch 6 = 32,
switch 7 = 64 and switch 8 = 128. The values of all switches which are in the ON position are
added to determine the address. (See illustration below) As an example, if the 1st and 3rd
switches are allocated to the ON position, the binary code is 00000101, so the corresponding
address is 5 (sw1 = 1 + sw3 = 4).
For complete, detailed settings please refer to the “Address Code Mapping Tables” on pages 25
and 26.

8
2.1.3 Baud Rate Settings
The 4th and 5th “Function” (FUN) DIP Switches set the Baud rate. Factory-default setting is
2400bps. This is the baud rate which SecurityTronix recommends for most installations.
Baud rates: 1200bps, 2400bps, 4800bps, 9600bps selectable
2.1.4 RS-485 Bus Matching Resistance
The 8th DIP switch of FUN SW2 is to select the matching resistor. In order to prevent
interference of the RS-485 communication signal and other signals, the parallel matching
resistor is needed in the communication interface of the dome camera at the far end of the
RS485 bus run.
Use the 8th switch of the FUN switch group to connect the resistor the the RS485 bus ONLY IF
THE CAMERA IS THE LAST CAMERAON THE BUS. If there are multiple PTZ cameras on the
RS485 bus, all others should not have a termination resistor applied.

9
2.2 Bracket Dimensions
2.2.1 Included Wall Mounted Bracket
2.2.2 Optional Corner Mounted Bracket

10
2.3 Installation of Brackets.
2.3.1 Wall Mounted
Fig 1
Installation conditions:
This wall mounted dome can be used on walls whose thickness and sturdiness should be
enough to install expansion bolt outdoors, or be used with an electrical box or mounted to a
stud indoors. The wall must be able to bear at least 4 times the weight of the dome.
To install the wall hanging bracket:
a. As shown in fig 2, use the installation holes of the wall hanging bracket as a pattern and mark
the locations of the holes on the wall.
Fig 2
b. As shown in fig 3, attach the wall hanging bracket to the wall with wire and cable passed
through it.

11
Fig 3
2.4 Connection
RS485 Connection
Before connecting, please turn off the power and read the instructions of all connected devices
carefully.
Fig 24
3. Instruction 3.1 Power Up Action
When initializing the system, the OSD screen shown at left will
appear after 2 seconds.
When restoring the original factory settings, please wait
patiently. The restore process takes roughly 1 minute to run.
(Continued on next page)
IR SPEED DOME
PROTOCOL PELCO-D/P
COMM 2400.N.8.1
DOME ID 001
MODULE
VERSION
PAN INIT
TILT INIT
POWER ON

12
This screen shows that the initialization of the pan/tilt motors
has completed.
.
Power up self-testing has completed.
3.2 Basic Function
Dome Operation
Use the control joystick up, down, left or right key on the keyboard.
Zoom
Press ZOOM- button to zoom “out” for a wider field of view for close objects.
Press ZOOM+ button to zoom “in” for a narrower field of view for distant objects.
Focus
Press FOCUS+ button to manually focus the camera on distant objects.
Press FOCUS- button to manually focus the camera on close objects.
Iris
Manual IRIS control is not supported on this camera module
IR SPEED DOME
PROTOCOL PELCO-D/P
COMM 2400.N.8.1
DOME ID 001
MODULE
VERSION
PAN OVER
TILT OVER
POWER ON
IR SPEED DOME
PROTOCOL PELCO-D/P
COMM 2400.N.8.1
DOME ID 001
MODULE BT-367
VERSION XXX
PAN OVER
TILT OVER
POWER ON

13
Preset Points
For SETTING, CALLING and DELETING presets, please refer to the instructions provided with
your PTZ controller.
Remark: Some preset points are reserved for special functions. See below.
3.3 Special Function Presets
The following presets are predefined for special functions. CALL the corresponding preset
using your controller to activate the function:
3.4 Screen Character Operation
Call preset 95 to enter the OSD, call preset 94 to exit the OSD.
Up or Down: Move the option of the OSD or change the value on the OSD.
Right: Enter the option, select the item or confirm.
Left: Return to main menu or cancel
Zoom Display Format: x XXX, XXX shows the present zoom of camera.
Time DisplayFormat: XXXX(year)-XX(month)-XX(day)
XX(hour)-XX(minute)-XX(second)
Angle Display Format: XXX.XX(pan)/XXX.XX(tilt)
IR Display: ☀means the IR is turned on. means the IR output power.
PREST
FUNCTION
PRESET
FUNCTION
33
Pan scan180 º
86
BLC on
34
Reset
87
BLC off
75
Call Pattern 1
88
Freeze on
76
Call Pattern 2
89
Freeze off
77
Call Pattern 3
91
A-B scan
78
Call Pattern 4
92
Set left point of A-B scan
79
Digital zoom on
93
Set right point of A-B scan
80
Digital zoom off
94
OSD menu Close
81
Auto day/night
95
OSD menu Open
82
Switch to night
96
Call tour 3
83
Switch to day
97
Call tour 2
84
Force on far light
98
Call tour 1
85
Force on near light
99
Pan scan

14
4 OSD Menu
4.1 Menu Index

15
4.1 System Information
SYSTEM INFORMATION
PROTOCOL: Displays the protocol of the dome.
Baud rate: represents the communication
Information; 2400 is the baud rate, which
can be changed via the DIP switches or
software the available baud rates are: 1200, 2400,
4800 and 9600. “N.8.1” represents the Check bit,
Data bit and Start bit.
DOME ID: This is the address number of the dome.
The range is 000-255.
MODULE: Displays the brand and model of the
installed camera module.
VERSION: Displays the current operating system
<SOFT ID SET>
DEVICE ID: Used to distinguish this dome from the
ID of other domes.
CHECK ID: Enter the device ID above into this field
to enable address changes for just this camera.
TARGET ID: Enter the new address you wish to
assign to this camera. It will be effective
immediately after it is changed.
<PASSWORD SET>
PASSWORD 1: Enter the password, PASSWORD 2: Re-enter the password
4.2 Dome Set
4.2.1 Preset
PRESET NO: Select the preset number to be SET
or CALLED.
CALL PRESET: Calls the preset number selected
above.
<SET PRESET: Writes the current camera position
into the preset location entered above.
<MAIN MENU>
<SYSTEM INFORMATION>
<DOME SET>
<CAM SET>
<IR SET>
<DISPLAY SET>
<TIME SET>
<LANGUAGE>
<RESET>
EXIT
<SYSTEM INFORMATION>
PROTOCOL PELCO-D/P
BAUD RATE 2400.N.8.1
DOME ID 001
MODULE
VERSION
MAX SPEED 300
<SOFT ID SET>
<PASSWORD SET>
CANCEL
CANCEL
<SOFT ID SET>
DEVICE ID
CHECK ID
TARGET ID
BAUDE RATE
SAVE
EXIT
<PRESET>
PRESET NO 001
CALL PRESET
<SET PRESET>
EXIT

16
To write the preset, enter the command on your PTZ
controller for “Call preset 1”. To cancel the write
operation, enter the command on your PTZ
controller for “Call preset 2”.
Because some presets are used to operate special functions,
they can’t be set and called normally.
4.2.2 Scan
SCAN SPEED: Scan speed includes setting the speed of
A-B scan and 360°scan.
A&B POINT SET:The effective scan range of the
A&B point boundaries is 20-340°.
4.2.3 Guard Tour
The camera can save 4 guard tours.
Each tour has 16 points (presets) and each point
can have its own dwell time and speed.
GUARD TOUR ID: Choose tour 1 thru 4.
CALL GUARD TOUR: Calls the guard tour.
<SET GUARD TOUR>
ID: These are the 16 steps available for the tour.
Each step will call 1 preset.
POINT: The preset for each step. Any preset from 1
thru 64 can be assigned to a step.
TIME: The default time of all points is 05s. The
range is 05-60s.
SPEED: The speed between two points in each
guard tour group can be set individually. The range is
1-64.
Note: Preset 33 and 34 can’t be set as guard tour point.
4.2.4 Pattern
<SCAN>
SCAN SPEED
<A POINT SET>
<B POINT SET>
CALLAB SCAN
CALL 360 SCAN
EXIT
CANCEL
<GUARD TOUR>
GUARD TOUR ID 1
CALL GUARD TOUR
<SET GUARD TOUR >
EXIT
<GUARD TOUR>
ID POINT TIME SPEED
01 01 05 64
02 02 05 64
03 03 05 64
04 04 05 64
05 05 05 64
06 06 05 64
07 07 05 64
08 08 05 64
PAGING
<GUARD TOUR>
ID POINT TIME SPEED
09 09 05 64
10 10 05 64
11 11 05 64
12 12 05 64
13 13 05 64
14 14 05 64
15 15 05 64
16 16 05 64
SAVE
<PRESET>
PRESET NO 001
CALL PRESET
<SET PRESET>
PRESET 1: SAVE
PRESET 2: BACK

17
PATTERN ID: Factory default is 1.
Select the pattern to be edited. There are 4 patterns.
CALL PATTERN: Call (run) the pattern which is
currently selected.
<PATTERN SET>
The figure at left shows the screen when the camera is ready to
record a pattern.
“XXX” is the quantity of operator’s instructions used so far. The
maximum amount of instructions available to record is 512.
Remark: The precision of pattern is associated with the system
settings and module of the camera. When using the pattern, it
is recommended to turn off the privacy zone and unnecessary
display function.
4.2.5 Privacy Zone (Unused on this model camera)
MASK NO.: Select the mask number. It
depends on the module supported.
SET MASK: For detailed steps, please refer to the
“Example of Setting Mask 1”.
MASK: ON and OFF are selectable.
Example of Setting Mask 1
1: Move the cursor to MASK NO, which is be selected
by pressing the “right key”.
2: Press the “up and down” keys in the keyboard to edit the
mask number, which is be entered by pressing the
right key. “-” means selecting this mode, while “ ”, hourglass
symbol, means editing this mode.
3: Move the cursor to <SET MASK> and press right key to set
the position of privacy zone. See the figure on the left below.
4: Move the joystick to aim at the object. Use the ZONE WIDE
and ZONE TELE keys in the keyboard to adjust the size of
picture. And use iris OPEN and CLOSE keys to adjust the size
of mask. Call preset 1 to save and exit and call preset 2 to exit
directly.
Remark: The mask size is better more than double the target
size. Setting the mask is associated with the pitch angle which
is advised to be equal to or less than 45°.
<PATTERN>
PATTERN ID 1
CALL PATTERN
<PATTERN SET>
EXIT
<PATTERN>
PATTERN ID 1
CALL PATTERN
<PATTERN SET>
XXX/512
PRESET 1: SAVE
PRESET 2: BACK
<DOME SET>
<PRESET>
<SCAN>
<GUARD TOUR>
<PATTERN>
<PRIVACY ZONE>
<OTHER>
<ALARM >
EXIT
<PRIVACY ZONE>
MASK NO 01
MASK
<SET MASK>
EXIT
<PRIVACY ZONE>
MASK NO 01
MASK ON
<SET MASK>
PRESET 1: SAVE
PRESET 2: BACK