See Water Oil Smart OSS20R6 User manual

Your Trusted Source for Quality Control Panels.
®
Oil Smart® Pump Switch
SEE WATER, INC.
Oil Smart Mounting: NEMA 6P; IP67
Mounting - Mount Oil Smart® Pump Control Sensor with provided
mounting hardware to the pump’s PVC discharge pipe. The ‘OFF’ sensor of
the Oil Smart® Switch shall be positioned at least 3” above the impeller of
the pump.
Testing:
Oil Smart® Pump Switch Testing:
• Place your thumb on the short stainless steel sensor of the Oil Smart®
Pump Switch, and the pump will turn on. While touching the short
‘ON’ sensor, touch the long ‘OFF’ sensor with your ngers; remove
your thumb from the short ‘ON’ sensor and begin to move your ngers
down the ‘OFF’ sensor simulating water being pumped down. Once
ngers are removed from ‘OFF’ sensor, the pump will turn off.
• Optional: Fill the sump area with ground water, when water reaches
the ‘ON’ sensor, the pump will turn on and remain on until water clears
the ‘OFF’ sensor.
Sequence of Operation:
Sump Cover
Check Valve
Pump Stop
Pump Start
Typical Installation of Oil Smart Ò Pump Switch
Oil SmartÒ Pump Switch
Submersible Pump #1
1
2
2
1
Normal Condition (Water Only)
When water comes in contact with the
short (on) sensor, the pump will turn
on. The pump will remain on until
water clears the long (off) sensor.
Oil Present Condition
If oil comes in contact with the (on)
sensor, the pump will not turn on.
Operation of Oil Smart®
Water (Oil Present Condition)
If the water level rises enough to
contact the (on) sensor under the
oil layer, the pump will turn on and
remain on until the (off) sensor clears
WATER
WATER
OIL
LAYER
WATER
OIL
LAYER
Oil Smart® Pump Switch: 120VAC
The Oil Smart® pump switch when combined with a non-auto sump pump,
will allow water to be pumped without the risk of pumping oil. This product
is ideal for elevator sumps, transformer containment areas, and city
underground vaults. Since 1995, the Oil Smart® switch has been the reliable
choice for safely pumping water.
Model FLA Range
OSS20R6 - MAHR.5 (0.0-9.8 FLA)
OSS20PBPR6 - MAPR1 (0.0-16.0 FLA)
OSS20R6E (230V 50/60 Hz.) (0.0-8.0 FLA)
www.seewaterinc.com
951.487.8073 • 888.733.9283 • [email protected]
22220 Opportunity Way, Suite 101 • Riverside, CA 92518
Page 1-2 IM 770 REV. 12/18

Your Trusted Source for Quality Control Panels.
®
SEE WATER, INC.
Notes:
Troubleshooting:
Caution: before checking electrical connections within the control or
attempting to replace any components, turn off all branch circuits supplying
power to the main control panel.
Pump control does not activate the pump or pump does not run
• Verify polarity is correct.
• Conrm all connections are tight and secure.
• White plastic case must be kept clean. Clean with house hold rubbing
alcohol and rag.
• Keep control 1” - 2” clear of any metallic material. Mount to PVC pipe
or if mounted to metal pipe, make sure to mount with See Water quick
mount PVC bracket.
Preventive Maintenance
• The Oil Smart® Pump Switch must be kept clean. If the switch is
submerged during install or maintenance, clean the white plastic case
with rubbing alcohol. Consistent inspection and preventive maintenance
ensures longevity and proper operation of components.
Warranty:
See Water® Inc. warrants that products of its manufacture
are free from defects in material and workmanship for a
period of 5 years from the date of purchase. This date shall be
determined by the date on the invoice and the serial number
on the product.
Replacement of the product is at the discretion of See Water
Inc. This warranty is valid when the product is installed in
compliance with the manufacturer’s installation instructions.
The manufacturer’s obligation under this warranty shall be
limited to the repair or replacement of any parts found by the
manufacturer to be defective, provided that the product is
returned to See Water’s factory, postage prepaid with proof of
original purchase included.
The manufacturer of this warranty shall not be liable under
this warranty if the product has not been properly installed;
any alterations/additions/changes to the product will result in
a void warranty. Failure to properly install and test this prod-
uct can result in personal injury or equipment malfunction.
See Water, Inc. shall not be liable for any loss, damage or
expenses from installation or use of its products.
Oil Smart® Pump Switch
www.seewaterinc.com
951.487.8073 • 888.733.9283 • [email protected]
22220 Opportunity Way, Suite 101 • Riverside, CA 92518
Page 2-2 IM 770 REV. 12/18