SeeEyes SC-IPH3002 User manual

Release Version 1.0
2 Port Ethernet Extender with PoE
SC-IPH3002
User’s Manual
SC-IPH3002

Release Version 1.0
1
Precaution and Safety Guidelines
The content of this guideline is to protect the safety of users and prevent property damage.
Please be sure to read this user’s manual thoroughly and use the device correctly.
Warning (If you do not keep any of the below guidelines, you may get seriously injured
or cause somebody’s death.)
■Be sure to install the product after unplugging power cord. Also, do not use many power
plugs at the same time.
- It may cause abnormal heat, fire and electric shock.
■Do not leave the device at any place that water falls or splashes. Also, do not put anything
full of water such as a flower vase on the device.
- It may cause malfunction or fire if liquid goes into the device
■Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble,
repair or modify it.
- By abnormal working, it may cause fire, electric shock and personal injury.
■Do not install this product in places with high humidity, dust, or soot.
- It may cause electric shock and fire.
■Always keep the location of the appliance clean during or after installation to prevent dust.
Especially when cleaning the device, wipe it with dry towel and do not use water, thinner or
organic solvent.
- It may cause damage to the surface of the device, malfunction or electric shock.
■Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper
temperature and avoid heating appliances like candle or heater. Also, keep the equipment or
tools away from places where people come and go.
- It may cause fire.
■Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power
extension cables, old power cords and a lack of safety earth. Consult your place of purchase or
professional if problems arise.
- It may cause fire and electric shock.
■Concerning the input voltage for operating this device, a voltage range must be within 10%
of rated voltage. Also, do not use a heat source such as a hair dryer, iron and refrigerator to the
same power unit.
- It may cause abnormal heat, fire and electric shock.
■Disconnect the power plug with care during thunder and lightning.
■Do not bend the power cord by excessive force. Make sure the power cord is not crushed by
heavy things.
- It may cause fire.
■Install the cable as “U” shape in order to prevent rain water/dew/fog, etc. from falling
through the cable.

Release Version 1.0
2
Caution (If you do not keep any of the below guidelines, you may get injured or suffer
property loss.
■Avoid installing near strong magnetic fields or radio waves and wireless devices such as radio
or TV.
- Install in a place that is free from magnetic, radio, or excessive vibration.
■Proper ambient temperature and humidity are recommended.
- Avoid extremely high temperatures(over 50°C) or low(below -10°C), and humid conditions.
■Do not place heavy items on the product or let foreign substances enter inside the device.
- It may cause failure.
■Install in well ventilated place, and avoid direct sunlight or heat appliance.
■Strong shock or vibration may cause device failure. Be careful when using the device.
- Install in a place without severe vibration.
■If you notice any unusual noise or smell, unplug the power supply immediately and contact
the place of purchase or service center.
- There may be a risk of fire and electric shock.
■Rotate the air properly in the system operating room and secure the cover of the main body.
- It may be the cause of failure by environmental factors.
■Refer the device to the service center and get regular checkup to maintain the performance
of the system.
- We are not responsible for any damages caused by user’s carelessness.
■Be sure to plug the power cord with grounded outlet.
- There is a risk of electrical shock and personal injury.
■Place the power plug in a location that is easy to operate.
- If a failure of the product occurred, the power plug must be unplugged to power down
completely. The power button on the main body does not completely disconnect power.
■Do not use this device in close proximity to a device that produces strong waves such as
radio set(TRANCEIVER, Walkie-talkie, etc.) or repeater. It may affect HD-SDI and EX-SDI signal,
or cause disorders such as noise or crack on the screen.
■The transmission medium(CABLE) must be a UTP(CAT.5e) cable.
■Be careful not to change the cable configuration during installation. (Refer to ‘4. CABLE PIN
Configuration’ on page 5.)
■This product’s CAMERA PORT has a maximum output power of 30W and the EXTENSION
PORT has a maximum output power of 30W. Please check the output power of each port when
connecting a camera or more than two product in series.
- The supply power is limited by the camera’s power consumption, transmission distance and cable loop
resistance, and may affect other channels.
■UTP(Unshielded Twisted Pair) Cable is for indoor use only. Use a STP(Shield Twisted Pair)
Cable which is covered for outdoor use.
■Transmission distance may vary depending on the type of UTP cable.
■Refer to the user’s manual for problems or questions besides the above. Contact our service
center if you need assistance from a professional technician.

Release Version 1.0
3
1. Introduction
1-1. Overview
SC-IPH3002 is a network transmission device that can extend PoE and data range.
This product can easily expand LAN cable in existing Ethernet environment where existing IP camera
is installed.
SC-IPH3002 is composed of 2 PoE output port, 1 PoE input port and DC adapter jack.
This product enables power supply to camera with its built-in PoE(Power Over Ethernet) function,
which eliminated the need of installing separate power cable. Also, it is able to reduce construction
period and costs by using LAN cable only.
In addition, this product is able to send video signals from the camera to the receiver device via LAN
cable.
1-2. Features
•Supply power to IP camera (PoE Type A supported)
•Extend PoE and Ethernet data transmission distance
(Please add/extend the product after checking the rated capacity of the IP camera you want to
use.)
•Save cable installation time with two or more multiple serial connections
•Auto MDI/MDIX
•Extend transmission distance by setting bandwidth switch (100Mbps/10Mbps).
100Mbps setting : Transmit up to 100m (CAT.5e)
10Mbps setting : Transmit up to 250m (CAT.5e)
•Power input: DC 48~56V Adapter or PoE (DC Adapter power priority)
2. Components
SC-IPH3002
User’s Manual
Adapter(DC 48V, 1.0A),
(Optional)
Mounting
Bracket
※The accessories included in the package may be changed.

Release Version 1.0
4
③
3. Product Parts & Functions
①CAMERA PORT: IP camera connection port. PoE Type A supported. (IEEE802.3 AF/AT)
- Port to supply power to camera with PoE or receive camera Data.
②EXTENSION PORT: IP camera connection port. Or extension port.
- Support PoE Type A from EXTENSION PORT. (IEEE802.3 AF/AT)
③Bandwidth Select Switch: 100Mbps, 10Mbps setting supported
※Transmit 100m in 100Mbps, transmit 250m in 10Mbps (over CAT5e)
④NVR PORT: NVR or PoE Switch HUB connection port. PoE Type A, B supported. (IEEE802.3
AF/AT)
⑤DC 48V~56V INPUT: DC Adapter 48V~56V power input port
※If power supply to NVR PORT is insufficient, connect external adapter.
<POWER, LINK/ACT Status LED>
※Caution
•To use SC-IPH3002 as a Switch Hub, connect external power.
•If a cable connected to EXTENSION PORT and NVR PORT are crossed, the power may not be
supplied and the image may not be output.
LED
LED Color
Status
Description
PWR
Red
ON
Power Input
OFF
No Power Input
EXT
Green
Flicker
EXTENSION PORT PoE Input, Data Input
CAM
Green
Flicker
CAMERA PORT PoE Input, Data Input
NVR
Green
Flicker
Data Input
④
②
⑤
①
③

Release Version 1.0
5
4. CABLE PIN Configuration (TIA / EIA 568B Way)
No.
Color
Color
Function
1
Orange + White
White
Orange
TX+
2
Orange
Orange
TX-
3
Green + White
White
Green
RX+
4
Blue
Blue
PWR+
5
Blue + White
White
Blue
PWR+
6
Green
Green
RX-
7
Brown + White
White
Brown
PWR-
8
Brown
Brown
PWR-

Release Version 1.0
6
5. Connection Diagrams
5-1. Basic Connection with Receiving Power from DC 48/56V Adapter
5-2. Basic Connection with Receiving Power from PoE Switching HUB
5-3. Multiple Connection with over 2 pcs of SC-IPH3002
※Additional power supply may be required depending on camera power consumption.
※Please configure general communication network (Internet/In-company, house) separated to
CCTV network.
※Bandwidth Switch 100Mbps Setting: Transmit Max. 100m (CAT.5e)
※Bandwidth Switch 10Mbps Setting: Transmit Max. 250m (CAT.5e)
※Bandwidth Switch 100Mbps Setting: Transmit Max. 100m (CAT.5e)
※Bandwidth Switch 10Mbps Setting: Transmit Max. 250m (CAT.5e)
※Bandwidth Switch 100Mbps Setting: Transmit Max. 100m (CAT.5e)
)
)
)

Release Version 1.0
7
5-4. Multiple Connection with 2 pcs of SC-IPH3002 in 10Mbps
※Set the Bandwidth switch to 10M before use.
※If the bandwidth exceeds 10Mbps after setting the Bandwidth switch to 10M, there may be a
problem with the video. Please be careful with the bandwidth when using the switch.
5-5. Recommended PoE Camera Power Consumption (Max. Power Output)
PoE Camera Power Consumption (Max. Power Output)
Adapter
PoE Camera #1
PoE Camera #2
PoE Camera #3
DC 48V
6W
9.5W
23.8W
DC 56V
9.2W
13W
29W
※Values in above table may vary depending on the type of camera and cable.
※Valued in above table may be changed when using PoE switch HUB
< PoE Camera Power Consumption Table Based on DC Adapter 48V 1.0A, 56V 1.16A >

Release Version 1.0
8
※Caution
①When installing more than 2 pcs of SC-IPH3002 in multiple connection using 1 DC adapter,
install the camera with higher power consumption close to the adapter.
②When installing more than 2 pcs of SC-IPH3002 in multiple connection, if there is not enough
power to drive PoE camera, connect an additional DC adapter to the SC-IPH3002 connected to the
camera with insufficient power.
(Refer to picture below)
※Bandwidth Switch 100Mbps Setting : Transmit Max. 100m (CAT.5e)
※Bandwidth Switch 10Mbps Setting : Transmit Max. 250m (CAT.5e)
※If the bandwidth exceeds 10Mbps after setting the Bandwidth switch to 10M, there may be a
problem with the video. Please be careful with the bandwidth when using the switch.
※It is not recommended to use 100Mbps and 10Mbps simultaneously when connecting more
than 2 pcs of SC-IPH3002.
※When connecting a camera with large power consumption or inrush current, please use a 56V
adapter or apply PoE+ to the product.

Release Version 1.0
9
6. Trouble Shooting Method
Condition
Check Method
Power is not
supplied.
•Check the power cable connection state.
•Check if the exclusive adapter is used.
•Check the PoE switch hub connection state.
•Check the CABLE PIN configuration state.
•Check if the connection to EXTENSION PORT and NVR PORT are
correct.
Video is not
displayed.
•Check the CABLE PIN configuration state.
•Check the cable transmission distance.
•Check the ground state.
•Check if the camera model is able to input PoE.
•Check if the camera is compatible with NVR.
•Check if the connection to EXTENSION PORT and NVR PORT are
correct.
Video status is
uneven.
•Check the CABLE PIN configuration state.
•Check the cable transmission distance.
•Check the ground state of the product.
•Check the set value of camera.
(Transmission video quality, frame rate, resolution, etc.)
•Check if the bandwidth is over 10Mbps after setting Bandwidth
Switch as 10M.
Network connection
state is abnormal.
•Check the NETWORK CABLE configuration.
•Check if there is any equipment that generates radio or strong
waves in the surrounding environment.
•Check if the Network configuration is installed properly.

Release Version 1.0
10
7. Specifications
Model No.
SC-IPH3002
Power
Input
DC Power
DC 48V or DC 56V Adapter
PoE Power
PoE IEEE 802.3af / 802.3at, Endspan / Midspan (Mode A / Mode B)
Feature
DC Adapter power supply priority (Between DC Adapter and PoE)
PoE Output
EXTENSION PORT
Max 30W, Standard PoE, IEEE802.3 af/at Mode A
CAMERA PORT
Max 30W, Standard PoE, IEEE802.3 af/at Mode A
Power Consumption
Max 1W (No-load Condition)
Max. Transmission Distance
In 100Mbps : Max. 100m (CAT.5e)
In 10Mbps : Max. 250m (CAT.5e)
Connection
Port
NVR PORT
RJ-45 1Port (TIA/EIA568B Type)
EXTENSION PORT
RJ-45 1Port (TIA/EIA568B Type)
CAMERA PORT
RJ-45 1Port (TIA/EIA568B Type)
POWER
DC JACK
RJ-45 Connector
Pin Assignment(Polarity)
1Pin: TX(+), PWR(+) 2Pin: TX(-), PWR(+)
3Pin: RX(+), PWR(-) 6Pin: RX(-), PWR(-)
LED
Indicator
PWR. LED
RED ON : Power Input, OFF: No Power Input
EXT. LED
GREEN Flicker : Video DATA Connected, OFF: Not Connected
CAM LED
GREEN Flicker : Video DATA Connected, OFF: Not Connected
NVR LED
GREEN Flicker : Video DATA Connected, OFF: Not Connected
Bandwidth Switch
Change Transmission Speed (100Mbps , 10Mbps)
Transmission Bandwidth
10/100Mbps (Full duplex)
Temperature / Humidity
-10°C ~ +50°C / 0 ~ 80%
Case Material / Weight
ABS / 52g
Dimensions (mm)
77(W) x 55(H) x 24(D)mm
※Using the LAN cable extension gender (coupler) causes signal attenuation. The use of multiple
gender connections is not recommended.
※Cable transmission distance may vary depending on the specifications of camera and NVR.
※When using the camera PoE function, the transmission distance may vary depending on the type
of camera.

Release Version 1.0
11
8. Warranty Certificate
Product No.
Model No.
Date of Purchase
Place of Purchase
Purchaser
Name
Address & Contact No.
Distributor
Name
Address & Contact No.
Warranty Period
Two(2) years from the date of purchase
Any failure that occurs in the normal use for only two years after purchase will be
repaired free of charge.
Contact the phone number listed on the user’s manual for repair.
When reporting the failure, please inform the model name and condition of the
product accurately. It is convenient to know the name and department of the person
in charge.
Please check this user’s manual again before reporting the failure.
Product shapes and circuits are subject to change without notice to improve
performance.
Faults following will be treated as a charge:
•Failure by user’s handling without care
•Not connecting the rated power
•Disassembled or repaired arbitrarily by user
•When replacing consumables
•Failure caused by natural disaster(lightning, fire, flood, tsunami, etc.)

Release Version 1.0
12
[MEMO]

Release Version 1.0
13
[MEMO]

Release Version 1.0
14
[MEMO]

Release Version 1.0
15
SeeEyes Co., Ltd
#503~509, 511~512, Sunil Technopia, 555 Dunchon-daero, Jungwon-gu,
Seongnam City, Gyeonggi Province, Korea (Zip Code: 13215)
TEL: [phone]
FAX: [phone]
EMAIL: [e-mail]
http://www.sscctv.com/eng