SeeEyes SC-IPE3001W User manual

Release Version 1.1
Waterproof Type IP PoE Extender
SC-IPE3001W
User Manual
SC-IPE3001W

Release Version 1.1
1
Precaution and Safety Guidelines
The content of this guideline is to protect the safety of users and prevent property damage.
Please be sure to read this user’s manual thoroughly and use the device correctly.
Warning (If you do not keep any of the below guidelines, you may get
seriously injured or cause somebody’s death.)
■Do not bend the UTC cable by excessive force. Make sure the UTC cable is not crushed by
heavy things.
- It may cause fire.
■Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble,
repair or modify it.
- Abnormal work could result in fire, electric shock, and injury.
■Do not install this product in places with high humidity, dust, or soot.
- It may cause electric shock and fire.
■Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper
temperature and avoid heating appliances like candle or heater. Also, keep the equipment or
tools away from places where people come and go.
- It may cause fire.
Caution (If you do not keep any of the below guidelines, you may get injured
or suffer property loss.)
■Avoid installing near strong magnetic fields or radio waves and wireless devices such as radio
or TV.
- Install in a place that is free from magnetic, radio, or excessive vibration.
■Proper ambient temperature and humidity are recommended.
- Avoid extremely high temperatures(over 50°C) or low(below -10°C), and humid conditions.
■Do not place heavy items on the product or let foreign substances enter inside the device.
- It may cause failure.
■Install in well ventilated place, and avoid direct sunlight or heat appliance.
■Install at a flat and stable place. Do not use an upright or slanted position.
- It may not operate properly or might be dangerous due to the fall of the device.
■Strong shock or vibration may cause device failure. Be careful when using the device.
- Install in a place without severe vibration.
■If you notice any unusual noise or smell, unplug the power supply immediately and contact
the place of purchase or service center.
- There may be a risk of fire and electric shock.
■Rotate the air properly in the system operating room and secure the cover of the main body.
- It may be the cause of failure by environmental factors.
■Refer the device to the service center and get regular checkup to maintain the performance
of the system.

Release Version 1.1
2
- We are not responsible for any damages caused by user’s carelessness.
■UTP(Unshielded Twisted Pair) Cable is for indoor use only. Use a STP(Shield Twisted Pair)
Cable which is shielded for outdoor use.
- Use standard UTP cable such as CAT.5e or above.
■Do not design and configure general network(Internet/indoor) together with CCTV network.
- It might be the cause of problem.
■Refer to the user’s manual for problems or questions besides the above. Contact our service
center if you need assistance from a professional technician.
1. Introduction
1-1. Overview
SC-IPE3001W is a waterproof & dustproof type of a 1-channel UTP Ethernet Data + PoE
Extender.
With its built-in power supply function (PoE IEEE802.3at), this product supplies power to camera
over UTP 1 cable.
To compensate for the short transmission distance of network equipment (shorter than 100m),
SC-IPE3001W extends the transmission distance up to 100~250m by installing this product in
the UTP cable section between camera and PoE HUB.
Also, it is able to reduce construction costs by supplying PoE to IP camera.
1-2. Features
•Transmit power + IP data over 1 UTP Cable(CAT.5e).
•IP67 rate (Waterproof & Dustproof)
•TCP Rate : 100Mbps Full Duplex
•Extend Ethernet Data transmission up to 100~250m by adding 1 pc of SC-IPE3001W.
(Add/extend the product after checking the rated capacity of IP camera you use.)
•Auto MDI/MDIX
•Built-in surge protection circuit
•Extend transmission distance by setting bandwidth switch (100Mbps/10Mbps).
100Mbps setting : Transmit up to 100m (CAT.5e)
10Mbps setting : Transmit up to 250m (CAT.5e)
※Make sure to turn the power of the product OFF/ON after changing the setting value.

Release Version 1.1
3
2. Components
SC-IPE3001W
Manual
3. Product Parts & Functions
①CAMERA SIDE : IP PoE camera connection port.
-Port to supply PoE and receive data from camera.
LED
LED Indicator
Yellow
ON
Successful PoE Input
OFF
No PoE Input
Green
ON
Connected to Camera
Flicker
Successful Data Transmission
OFF
No Data Transmission
②NVR SIDE : NVR or PoE Switch HUB connection port.
-Port to receive power from PoE Switch HUB / PoE Injector and supply power and data to
camera.
LED
LED Indicator
Yellow
ON
Successful PoE Input
OFF
No PoE Input
Green
ON
Successful LINK connection to NVR or network device
Flicker
Successful Data connection to NVR or network device
OFF
No LINK connection to NVR or network device
①
②

Release Version 1.1
4
③Bandwidth Selector Switch : Switch for selecting network bandwidth
(100Mbps / 10Mbps setting)
- Able to change the bandwidth by setting the switch as 100Mbps<->10Mbps.
※Due to the characteristics of the product, the switch is not exposed outside
※To adjust the switch, open the Top Case.
However, after changing the setting value, please turn OFF/ON the product power.
※Factory default setting is 100Mbps.
4. Application diagram
4-1. PoE power supply from the PoE Switch Hub
4-2. Multiple Connections with 2 pcs of SC-IPE3001W at 100Mbps
Switch
Transmission
Bandwidth
Maximum Transmission Distance
ON
100Mbps
100m(CAT.5e)
OFF
10Mbps
250m(CAT.5e)
③
※Bandwidth Switch 100Mbps Setting: Transmit Maximum 100m (CAT.5e)
※Bandwidth Switch 10Mbps Setting: Transmit Maximum 250m (CAT.5e)

Release Version 1.1
5
4-3. Multiple Connections with 2 pcs of SC-IPE3001W at 10Mbps
※Able to extend as above figure. The max. extension distance may vary depending on the
rated capacity of IP camera, characteristics of the cable, and the added SC-IPE3001 quantity.
※Network Link-time may be longer as the number of Extenders is increased.
※Setting Bandwidth Switch as 100Mbps: Transmit Maximum 100m (CAT.5e)
※Setting Bandwidth Switch as 10Mbps: Transmit Maximum 250m (CAT.5e)
※If the bandwidth exceeds 10Mbps after setting the Bandwidth Switch to 10M, there may
be a problem with the video.
※Maximum Power Output in SC-IPE3001W 100Mbps Setting
SC-IPE3001W
Power Input
SC-IPE3001W
Connection Quantity
Max. Power Output
100Mbps/100m
PoE
1
14W
2
10W
3
6W
4
3W
PoE+
1
25W
2
20W
3
14W
4
9W
※Maximum Power Output in SC-IPE3001W 10Mbps Setting
※It is not recommended to use 100Mbps and 10Mbps simultaneously when connecting more
than 1 pc of SC-IPE3001W.
(If you set two different bandwidth settings, the bandwidth is automatically set to 10Mbps.)
※When connecting a camera of large power consumption or high inrush current, please
use PoE+.
SC-IPE3001W
Power Input
Maximum Power Output
10Mbps/250m
SC-IPE3001W x1
SC-IPE3001W x2
PoE
7W
3W
PoE+
13W
8W
Additional use of
100Mbps is NOT
recommended

Release Version 1.1
6
5. How to connect cables and waterproof caps
※As shown in the image above, remove the waterproof cap of the product and
connect the UTP cable.
※For proper waterproof, be sure to close the waterproof cap tightly.
6. CABLE PIN Array
No.
Color
Color
Function
1
Orange + White
White
Orange
TX+
2
Orange
Orange
TX-
3
Green + White
White
Green
RX+
4
Blue
Blue
PWR+
5
Blue + White
White
Blue
PWR+
6
Green
Green
RX-
7
Brown + White
White
Brown
PWR-
8
Brown
Brown
PWR-

Release Version 1.1
7
7. Troubleshooting
Symptom
Identification Method
No PoE
•Check the PoE switch hub connection state.
•Check the CABLE PIN array.
•Check the connection between the NVR and the Camera
No Video
•Check the CABLE PIN array.
•Check the cable transmission distance.
•Check the ground state.
•Check if the camera model is able to input PoE.
•Check if the camera is compatible with NVR.
Unstable Video
•Check the CABLE PIN array.
•Check the cable transmission distance.
•Check the ground state of the product.
•Check the set value of camera.
(Transmission video quality, frame rate, resolution, etc.)
•Check if the bandwidth is over 10Mbps after setting Bandwidth
Switch as 10M.
Unstable Network
•Check the NETWORK CABLE configuration.
•Check if there is any equipment that generates radio or strong waves in
the surrounding environment.
•Check if the Network configuration is installed properly.

Release Version 1.1
8
8. Specifications
Model
SC-IPE3001W
Power Input
PoE
PoE IEEE 802.3af / 802.3at
Endspan / Midspan (Mode A / Mode B)
PoE Output
Midspan only (Mode B)
Power Consumption
0.5W Max.
Maximum Transmission
Distance
In 100Mbps : Max. 100m (CAT.5e)
In 10Mbps : Max. 250m (CAT.5e)
Transmission Bandwidth
10/100Mbps (Full duplex)
RJ-45 Connector
Pin Assignment(Polarity)
1Pin: TX(+), 2Pin: TX(-), 3Pin: RX(+), 4Pin: PWR(+),
5Pin: PWR(+), 6Pin: RX(-), 7Pin: PWR(-), 8Pin: PWR(-)
LED
Indicator
CAMERA SIDE
YELLOW ON : Power Input
YELLOW OFF : No Power Input
Green ON : Connected to Camera
Green Blinking : Successful Data Transmission
Green OFF : No Data Transmission
NVR SIDE
YELLOW ON : Power Input
YELLOW OFF : No Power Input
Green ON : Connected to NVR
Green Blinking : Successful Data Transmission
Green OFF : No Data Transmission
Maximum Power Output
25.5W based on IEEE802.3at Power Device
(This may vary depending on the condition of the cable and the number
of connected products.)
Bandwidth Switch
Transmission Bandwidth Settings: 100Mbps or 10Mbps
Connection
Port
CAMERA SIDE
RJ-45 1Port (TIA/EIA568B Type)
NVR SIDE
RJ-45 1Port (TIA/EIA568B Type)
IP Rate
IP67: Waterproof & Dustproof
Temperature / Humidity
-10°C~+50°C / 0 ~ 80%
Case Material / Weight
ABS / 120g
Dimensions (mm)
122(W) x 43(H) x 25(D) mm
※Using the LAN cable extension gender (coupler) causes signal attenuation. The use of multiple
gender connections is not recommended.
※Cable transmission distance may vary depending on the specifications of camera and NVR.
※When using the camera PoE function, the transmission distance may vary depending on the type
of camera

Release Version 1.1
9
9. Warranty Certificate
This product has passed thorough quality control and test, and if this gets broken during
normal use, we provide the two-year warranty service.
Model No.
Serial No.
Distributor
Date you purchased
Place you purchased
Warranty Period
Two (2) year from the date of purchase
Purchaser
Name
Address
•Please check this warranty indication first.
•Please contact your distributor after checking out any defect in the products.
•The standard for repairing, replacement or reimbursement follows Customer.
•Warranty content any defect under normal use within the warranty service period we
give you free repair service according to the warranty certificate.
•We charge you with the fee of parts and service despite of free warranty service period.
Any breakage made without care such as:
- Breakdown due to natural disasters (lightning, fire, flood, tsunami, etc.)
- When disassembled or repaired by the user
- When connecting power other than rated power.
- When you want to reassemble for full system or replace parts within warranty
service period.
- When unauthorized person modified or made damage on the product trying to
repair it.
- Failure due to careless handling of the user
- When replacing consumables
- Lightning strike.
•Please note that we don’t support the breakage after warranty service period expired. If
the customer wants to get it repaired, we charge them with the fee.
•The specification is subject to change without prior notice for quality improvement.

Release Version 1.1
10
MEMO

Release Version 1.1
11
SeeEyes Co., Ltd
#503~509, 511~512, Sunil Technopia, 555 Dunchon-daero, Jungwon-gu,
Seongnam City, Gyeonggi Province, Korea (Zip Code: 13215)
TEL: [phone]
FAX: [phone]
EMAIL: [e-mail]
http://www.sscctv.com/eng