weBoost Home MultiRoom User manual

NEED HELP? www.weboost.ca 866.294.1660
Installation Guide
Cell Signal Booster
Home MultiRoom
Home MultiRoom
A WILSON ELECTRONICS BRAND
FRANÇAIS ENGLISH

Package Contents 1
Preparation 2
STEP 1-A & B: Inside Antenna & Booster Placement 3
STEP 2: Mount & Point Outside Antenna Toward Nearest Cell
Tower 5
STEP 3-A: Route & Connect Outside Antenna To Booster 8
STEP 3-B: Route & Connect Inside Antenna To Booster 9
STEP 4: Power Up The Booster & Optimize The System 10
Measuring Booster Performance 12
Light Patterns 14
Troubleshooting 15
Safety Guidelines 16
Specifications 19
Warranty 20
______
Index

1
HOME MULTIROOM CELL PHONE SIGNAL BOOSTER
ENGLISH
______
Package
Contents
Home
MultiRoom
Outside Antenna
Mounting Bracket
Window Entry
Cable
(951177)
Wall Mount Brackets
w/Command Strips
Cable Mounting
Clips Qty. 15
Inside
Antenna
(314440)
Outside
Antenna
(314445)
30’ & 2-15’
Cables (950630),
(YX030-15W w/971129
Barrel Connector)
Power
Supply
(850018)

2CELL PHONE SIGNAL BOOSTER HOME MULTIROOM
ENGLISH
______
Preparation
NOTE: These instructions will walk you through a “soft” install process to
find the optimal locations for the inside and outside antennas, then through
the process of the permanent installation.
You Will Need (tools not included)
Make sure the following materials are prepared and ready for your
installation.
o Ladder
o Drill (if routing cable through wall)
o 1”-3” diameter existing pole for mounting
Outside Antenna (#901117 Pole Mount can be
purchased separately if needed)
o Recommended: Power Strip with surge protection
1 to 2 hours
1 Person (2 people to make antenna calibration easier)

3
HOME MULTIROOM CELL PHONE SIGNAL BOOSTER
ENGLISH
NOTE: Do not connect booster to power until the system is fully installed.
______
Step 1-A & B: Inside Antenna
& Booster Placement
Place the Inside Antenna where you need the greatest signal boost
and place Booster in your desired location at least 24” away from
Inside Antenna.
À
A
U
M
O
INS
2
4
PO
DE
D
IST
A
NCE
TIP: The cable from the Inside Antenna can be
routed into the ceiling and connected to the
coax cable out-of-sight for a better look.

4CELL PHONE SIGNAL BOOSTER HOME MULTIROOM
ENGLISH
Inside Antenna Mounting Options
Mounted
Vertical
Command
Strips
Command Strips
Mounted
Horizontal
Or use the
kickstand and
set on desktop
______
(STEP 1-A & B cont.)
The Inside Antenna can be mounted horizontal, vertical or on a
desktop. Command strips can be used to secure mounting bracket.

5
HOME MULTIROOM CELL PHONE SIGNAL BOOSTER
ENGLISH
______
Step 2: Mount & Point
Outside Antenna Toward
Nearest Cell Tower
NOTE: Mounting on existing roof exhaust pipe
would be a good time-saver option. Watch out for
power lines.
Outside Antenna
Mount
Bracket
Clamps
Pole mounting and wall mounting options are included. The pole mounting
option is preferred because it will be easier to adjust to the direction of
the cell tower.
Attach the Mount to the Outside Antenna and use the Bracket Clamps to
attach the Antenna to a pole or exhaust pipe.
Pole
(1.0”-3.0”dia.)

6CELL PHONE SIGNAL BOOSTER HOME MULTIROOM
ENGLISH
Point the Outside Antenna toward the nearest cell phone tower. To find the
nearest tower, use an app such as ‘Open Signal’. This is the most critical
step of the installation process because it will determine the overall
performance of the booster system.
The greater the separation between the Inside and Outside Antennas, the
better performance you will get from the booster.
Outside Antenna
NOTE: The Outside Antenna must be at least
50 feet horizontal or 20 feet vertical from
the Inside Antenna for best performance.
Make sure the Inside Antenna and Outside
Antennas are setup so they are facing away
from each other.
Cell Tower
______
(STEP 2 cont.)

7
HOME MULTIROOM CELL PHONE SIGNAL BOOSTER
ENGLISH
If there’s not a pole to easily mount the Outside Antenna, this may be
mounted on the fascia by fastening the bracket as shown below.
______
(STEP 2 cont.)
Mounting On Side Of Roof (Fascia)
Cable Mounting Clips provided
Using only the back Bracket Clamp
for mounting
TIP: Make sure to do the optimization test on Step 4 to find the best side of
your house before you mount this on the fascia.

8CELL PHONE SIGNAL BOOSTER HOME MULTIROOM
ENGLISH
______
Step 3-A: Route & Connect
Outside Antenna To Booster
The greater the separation, the better
the Booster performance
Connect the white RG-6 Cable to Outside Antenna and route cable
into the home. A Window Entry Cable is provided to help make cable
entry easier. All connections should be finger tightened only.
Route cable to the Home MultiRoom Booster and connect to the port
labeled ‘OUTSIDE ANTENNA’.
Outside
Antenna
connection
Window Entry
Cable
15’ RG-6 Cable15’ RG-6 Cable
Outside
Antenna
Cell
Tower
Booster
Booster
Cable Mounting Clips
provided

9
HOME MULTIROOM CELL PHONE SIGNAL BOOSTER
ENGLISH
connection
______
Step 3-B: Route & Connect
Inside Antenna To Booster
Inside
Antenna
30’ RG-6 Cable
Booster
Connect the white 30’ Cable to Inside Antenna and route to the
Home MultiRoom Booster and connect to the port labeled
‘INSIDE ANTENNA’.
The greater the separation, the better
the Booster performance
Outside
Antenna
Inside
Antenna
Cell
Tower
Booster
Cable Mounting Clips provided

10 CELL PHONE SIGNAL BOOSTER HOME MULTIROOM
ENGLISH
______
Step 4: Power Up The
Booster & Optimize The
System
Plug the Power Supply into wall outlet then connect to end of booster
labeled “ ” (turn 90° to lock connector).
Outside
Antenna
Cell
Tower
Booster
50 FEET HORIZONTAL OR 20 FEET
VERTICAL DISTANCE
Inside
Antenna
to power
to power
NOTE: We strongly recommend using a power strip with surge protection.
Can
be wall
mounted
Command
Strips

11
HOME MULTIROOM CELL PHONE SIGNAL BOOSTER
ENGLISH
After powering up your system, you are now ready to optimize your system.
Rotate the Outside Antenna in 1/8 turn increments, after each turn, unplug
and reconnect the booster to power while observing the signal level on
your cell phone from the Inside Antenna’s projected area. Secure the
Outside Antenna in place, pointing in the direction that gives you the
strongest signal. Enjoy your boosted signal!
After each rotation, observe signal level
on your cell phone from the Inside Antenna’s
projected area. This is done best by having someone
near the inside antenna taking signal measurements
after the person outside makes each rotation.
______
(STEP 4 cont.)

12 CELL PHONE SIGNAL BOOSTER HOME MULTIROOM
ENGLISH
______
Measuring Booster
Performance
Settings > About Phone > Status or Network > Signal Strength
or Network Type and Strength (exact options/wording
depends on phone model).
Android™
iPhone is a registered trademark of Apple Inc. Android is a trademark of Google Inc.
iOS 11 and later no longer displays the decibel (dBm) reading
in ‘Field Test Mode’. Tip: Using the dot signal strength indicator
on your cell phone can assist you in finding the strongest
signal direction as well as placing calls in dierent locations.
For changes/updates on this issue, periodically go to
weboost.com/signalstrength.
iPhone®
How To Get Signal Strength As A Number
All Other Phones & Alternate Methods
Go to www.weboost.com/test-mode-instructions/

13
HOME MULTIROOM CELL PHONE SIGNAL BOOSTER
ENGLISH
EXCELLENT GOOD FAIR POOR DEAD ZONE
3G/1x
4G/LTE
-70dBm
-90dBm
-71 to -85dBm
-91 to -105dBm
-86 to -100dBm
-106 to -110dBm
-101 to -109dBm
-111 to -119dBm
-110dBm
-120dBm
SIGNAL
STRENGTH
EXCELLENT GOOD FAIR POOR DEAD ZONE
3G/1x
4G/LTE
-70dBm
-90dBm
-71 to -85dBm
-91 to -105dBm
-86 to -100dBm
-106 to -110dBm
-101 to -109dBm
-111 to -119dBm
-110dBm
-120dBm
SIGNAL
STRENGTH
Having an accurate measurement of signal strength in decibels (dBm) is crucial when
installing your system. Decibels accurately measure the signal strength you are receiving.
DID YOU KNOW a signal increase of just 3dB is 2
times the power and signal amplification!
Compare Results
______
(MEASURING BOOSTER PERFORMANCE cont.)
Signal Strength with Booster
Note here:
Signal Strength without Booster
Note here:

14 CELL PHONE SIGNAL BOOSTER HOME MULTIROOM
ENGLISH
______
Light Patterns
Solid Green
This indicates that your booster is
functioning properly and there are
no issues with installation.
Blinking Green & Red
Band has reduced gain. This indicates
that one or more of the booster bands has reduced power due to a feedback loop
condition called oscillation. This is a built in safety feature to prevent harmful interference
with a nearby cell tower. If you are already experiencing the desired signal boost, then
no further adjustments are necessary. If you are not experiencing the desired boost in
coverage then refer to the Troubleshooting section.
Solid Red
Band has shutoff. This is due to a feedback loop condition called oscillation.
This is a built in safety feature that causes a band to shut off to prevent harmful
interference with a nearby cell tower. Refer to Troubleshooting section.
Blinking Green & Yellow
Band has reduced gain. This indicates that one or more of the booster bands has reduced
power due to overload from a nearby cell tower. This is a built in safety feature to
prevent harmful interference with a nearby cell tower. If you are already experiencing
the desired signal boost, then no further adjustments are necessary. If you are not
experiencing the desired boost in coverage then refer to the Troubleshooting section.
Solid Yellow
Band has shutoff due to overload from nearby cell tower. Outside Antenna must be
adjusted. Refer to Troubleshooting section.
Light O
If the Signal Booster’s light is off, verify your power supply has power.
Home MultiRoom

15
HOME MULTIROOM CELL PHONE SIGNAL BOOSTER
ENGLISH
______
Troubleshooting
FIXING ANY RED LIGHT ISSUES
FIXING ANY YELLOW LIGHT ISSUES
1
2
3
Verify Outside and Inside Antenna face away from each other. Un-plug and
re-plug in power supply.
Verify the Inside Antenna is at least 24” from the Booster and pointed away
from the Booster. Unplug and re-plug in power supply.
Tighten all cable connections (be sure to finger tighten only, do NOT use tools).
You may want to undo and redo the connection completely. Unplug and re-
plug in power supply.
Increase the distance (horizontally or vertically) between the Outside and
Inside antenna. Add included cable if needed. Un-plug and re-plug in
power supply.
Outside Antenna must be adjusted. Wait 10 seconds between adjustments for
the lights to reset.
4
This involves Solid Red & Blinking Green/Red lights.
This involves Solid Yellow & Blinking Green/Yellow lights.
IF YOU ARE HAPPY WITH THE COVERAGE, THESE LIGHT ISSUES DON’T HAVE TO
BE RESOLVED. YOUR CARRIER’S BAND HAS NOT BEEN AFFECTED.
Pole Mount Option: Rotate the Outside Antenna away from the strongest
cellular signal in small increments (45°) until the light turns green. Unplug and
re-plug in power supply.
Mounting On Side Of Roof Option: Change mount location. Move the Outside
Antenna to a dierent location of the home/building to see if the lights turn
green. Un-plug and re-plug in power supply. Then secure in place.
NEED HELP? www.weboost.ca 866.294.1660

16 CELL PHONE SIGNAL BOOSTER HOME MULTIROOM
ENGLISH
______
Safety Guidelines
To uphold compliance with network protection standards, all active cellular devices must
maintain at least six feet of separation distance from Inside Panel and Dome antennas and
at least four feet of separation distance from desktop Antenna.
Use only the power supply provided in this package. Use of a non-weBoost product may
damage your equipment.
The Signal Booster unit is designed for use in an indoor, temperature-controlled
environment (less than 100 degrees Fahrenheit). It is not intended for use in attics or
similar locations subject to temperatures in excess of that range.
RF Safety Warning: Any antenna used with this device must be located at least 8 inches
from all persons.
AWS Warning: The Outside Antenna must be installed no higher than 10 meters (31’9”)
above ground.
FOR MORE INFORMATION ON REQUIREMENTS SET OUT IN ISED CPC-2-1-05,
SEE BELOW:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html
This is a CONSUMER device.
BEFORE USE, you MUST meet all requirements set out in CPC-2-1-05.
You MUST operate this device with approved antennas and cables as specified by the
manufacturer. Antennas MUST NOT be installed within 20 cm of any person.
You MUST cease operating this device immediately if requested by ISED or licensed
wireless service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls
served by using this device.
This device may operate in a fixed location only, for in-building use.

17
HOME MULTIROOM CELL PHONE SIGNAL BOOSTER
ENGLISH
______
Antenna Kit Options
This radio transmitter 4726A-460044 has been approved by Innovation, Science and
Economic Development Canada to operate with the antenna types listed below, with the
maximum permissible gain indicated. Antenna types not included in this list that have a gain
greater than the maximum gain indicated for any type listed are strictly prohibited for use
with this device.
Outside antenna maximum permissible
antenna gain (dBi) 50
Inside antenna maximum permissible
antenna gain (dBi) 50
4.50 4.50 4.50
3.76 4.13 4.77 4.83
BAND 12/17 BAND 13 BAND 5 BAND 4 BAND 25/2
Ω
50
50
75
75
75
1
3
1
3
1
2
3
2
3
1
Included
Antennas Included Splitters
Antenna # Splitter #Antenna Type Splitter Type
311135
311135
311155
311155
311155
Wall Mount Panel
Wall Mount Panel
Wall Mount Panel
Wall Mount Panel
Wall Mount Panel
859980
859957
850035
850034
850034
3 Way Splitter
2 Way Splitter
3 Way Splitter
2 Way Splitter
2 Way Splitter
Kit #
309900-50N
309905-50N
309902-75F
309903-75F
309904-75F
INSIDE ANTENNA EXPANSION KITS
ΩAntenna TypeCoax TypeKit # Ln(ft)
FIXED INSIDE ANTENNA KIT OPTIONS
3.8 4.7
4.55
All equivalent or lesser antennas and cables are suitable for use with 460044 Signal Booster.
301121-40010
301151-0610
304412-40010
304412-5810
304419-0610
304419-1110
304419-17410
311135-40060
311135-5825
311155-0640
311155-1170
311155-40060
314440-0630
314440-1160
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Panel
Panel
Panel
Panel
Panel
4G Panel
4G Panel
LMR-400
RG-6
LMR-400
RG-58
RG-6
RG-11
RG-174
LMR-400
RG-58
RG-6
RG-11
LMR-400
RG-6
RG-11
10
10
10
10
10
10
10
60
25
40
70
60
30
60
50
75
50
50
75
75
50
50
50
75
75
50
75
75

18 CELL PHONE SIGNAL BOOSTER HOME MULTIROOM
ENGLISH
ΩAntenna TypeCoax TypeKit #
301126
301111-0675
301111-11140
301111-400170
301111-5850
304421-0610
304421-1120
304421-17410
304421-5810
304422-1120
304422-40020
304422-5810
311141-0620
311141-1120
311201-0620
311201-1120
311203-40020
311203-5820
314411-40075
314411-5825
314445-0630
314445-100100
314445-1175
314445-40075
314453-40075
314453-5825
314473-0640
314473-1175
314475-0630
314475-1175
RG-174
RG-6
RG-11
LMR-400
RG-58
RG-6
RG-11
RG-174
RG-58
RG-11
LMR-400
RG-58
RG-6
RG-11
RG-6
RG-11
LMR-400
RG-58
LMR-400
RG-58
RG-6
LMR-100
RG-11
LMR-400
LMR-400
RG-58
RG-6
RG-11
RG-6
RG-11
Mini-Mag
Yagi
Yagi
Yagi
Yagi
Omni Consumer
Omni Consumer
Omni Consumer
Omni Consumer
Omni Enterprise
Omni Enterprise
Omni Enterprise
Grey Brick
Grey Panel
Omni Directional
Omni Directional
Omni Directional
Omni Directional
Wide Band Directional
Wide Band Directional
4G Directional
4G Directional
4G Directional
4G Directional
Panel
Panel
Panel
Panel
Wide Band Directional
Wide Band Directional
12.5
75
140
170
50
10
20
10
10
20
20
10
20
20
20
20
20
20
75
25
30
100
75
75
75
25
40
75
30
75
50
75
75
50
50
75
75
50
50
75
50
50
75
75
75
75
50
50
50
50
75
50
75
50
50
50
75
75
75
75
Ln(ft)
FIXED OUTSIDE ANTENNA KIT OPTIONS
______
(ANTENNA KIT OPTIONS cont.)