SeeEyes SC-HOC01S User manual

Release Version 1.2
3G, HD-SDI, EX-SDI1.0 Optical Extender
SC-HOC01S
User’s Manual
Precaution and Safety Guidelines
The content of this guideline is to protect the safety of users and prevent property damage.
Be sure to read this user’s manual thoroughly and use the device correctly.
Warning (If you do not keep any of the below guidelines, you may get seriously injured or
cause somebody’s death.)
■Do not disassemble the device arbitrarily as its exclusive adapter has electric shock hazard.
■Disconnect the power cord if the device is not in use.
■Avoid direct sunlight, high temperature, high humidity and low temperature. Place the device in well
ventilated site.
■Strong shock or vibration may cause device failure, so use with caution.
■Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble, repair or
modify it.
- By abnormal working, it may cause fire, electric shock and personal injury.
■Avoid installing near strong magnetic fields or radio waves and wireless devices such as radio or TV.
■If rain, coffee or foreign substances entered the device, fire or electric shock may occur in the event of
smoke or smell. Unplug the power cord immediately and contact the place of purchase or service center.
■Always keep the location of the appliance clean during or after installation to prevent dust. Especially
when cleaning the device, wipe it with dry towel and do not use water, thinner or organic solvent.
■Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper temperature and
avoid heating appliances like candle or heater. Also, keep the equipment or tools away from places where
people come and go.
- It may cause fire.
■Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power extension
cables, old power cords and a lack of safety earth. Consult your place of purchase or professional if
problems arise.
- It may cause abnormal heat, fire and electric shock.
■Concerning the input voltage for operating this device, a voltage range must be within 10% of rated
voltage, and the power outlet must be grounded. Also, do not use a heat source such as a hair dryer, iron
and refrigerator to the same power unit.
- It may cause abnormal heat, fire and electric shock.

Release Version 1.2
1
Caution (If you do not keep any of the below guidelines, you may get injured or suffer
property loss.)
■Be sure to disconnect the power cord during installation or working.
■Proper ambient temperature and humidity are recommended.
- Avoid extremely high temperature (over 50C) or low (below -10C) and humid conditions.
■Do not place heavy items on the product or let foreign substances enter inside the device.
- It may cause failure.
■Install in well ventilated place, and avoid direct sunlight or heat appliance.
■Install at a flat and stable place. Do not use an upright or slanted position.
- It may not operate properly or might be dangerous due to the fall of the device.
■Strong shock or vibration may cause device failure. Be careful when using the device.
- Install in a place without severe vibration.
■Make sure to check the specification and usage of the device before performing the installation.
■During installation, secure space to emit heat between devices.
■Refer the device to the service center and get regular checkup to maintain the performance of the
system.
- We are not responsible for any damages caused by user’s carelessness.
■Place the power plug in a location that is easy to operate.
- If a failure of the product occurred, the power plug must be unplugged to power down completely.
■Disconnect the power plug with care during thunder and lightning.
■Do not use this device in close proximity to a device that produces strong wave such as radio set
(TRANCEIVER, Walkie-talkie, etc.) or a repeater. It may affect the image signal, or cause disorders such as
noise or crack on the screen.
■Refer to the user’s manual for problems or questions besides the above. Contact our service center if
you need assistance from a professional technician.
1. Introduction
1-1. Overview
SC-HOC01S is a compact type module that transmits 3G, HD-SDI, EX-SDI 1.0 video signal by optical
cable. This product consists of Transmitter and Receiver, and can transmit 3G, HD-SDI, EX-SDI 1.0
signal by optical cable with minimum loss. The transmitter converts 3G, HD-SDI, EX-SDI 1.0 signal
into optical data, and the receiver converts optical data received from optical cable into 3G, HD-SDI,
EX-SDI 1.0 signal.
1-2. Features
•Separated Transmitter and Receiver
•Can transmit 3G, HD-SDI, EX-SDI1.0 maximum 20Km by Single mode fiber
•BNC connector applied to SDI, LC connector applied in Optical
•DC12V/AC24V power supply available

Release Version 1.2
2
2. Components
Transmitter
Receiver
DC incoming line
User’s Manual
3. Product Parts and Peripheral Device Connection
3-1. Transmitter
①HD-SDI INPUT: 3G, HD-SDI, EX-SDI1.0 signal input port.
②SIGNAL LED Status Indicator
LED Status
Status Indicator
RED ON
SDI Signal Input ON
RED OFF
SDI Signal Input OFF
③POWER LED Status Indicator
LED Status
Status Indicator
RED ON
Power Input ON
RED OFF
Power Input OFF
④Optical OUT: Optical signal output port.
⑤POWER IN: DC12V/ AC24V input port.
①
②
③
④
⑤

Release Version 1.2
3
3-2. Receiver
①HD-SDI OUTPUT: 3G, HD-SDI, EX-SDI1.0 signal output port.
②SIGNAL LED Status Indicator
LED Status
Status Indicator
RED ON
Optical Input ON
RED OFF
Optical Input OFF
③POWER LED Status Indicator
LED Status
Status Indicator
RED On
Power Input ON
RED OFF
Power Input OFF
④Optical IN: Optical Signal input port.
⑤POWER IN: DC12V/ AC24V input port.
4. System Configuration and Optical Cable Transmission Distance
4-1. System Configuration Example
•Connect 3G, HD-SDI, EX-SDI 1.0 CAMERA output to HD-SDI input of Transmitter and connect
optical output to optical cable. Connect optical cable to optical input of Receiver and connect HD-
SDI output to DVR.
•3G, HD-SDI, EX-SDI 1.0 video can be transmitted maximum 20Km by optical SINGLE MODE cable.
①
②
③
④
⑤

Release Version 1.2
4
4-2. Optical Cable Transmission Distance
SDI
Single mode fiber
(SM G.657B3)
Multi mode fiber
(MM50 / 125um OM3)
EX-SDI 270Mbps
20Km
3Km
FULL HD 1.5Gbps
20Km
1Km
FULL HD 3Gbps
20Km
700m
5. Trouble Shooting Method
Condition
Check Method
The power is not on.
•Check the adapter input status.
•Check if the POWER LED of transmitter and receiver is on.
The video is not
displayed.
•Check if the signal LED of receiver is on.
•Check if the signal LED of transmitter is on.
•Check if the LC Type connecter is connected to optical terminal.
•Check if the BNC CABLE is connected in the proper direction.
•Check the BNC connecter connection status.
•Check if the camera is compatible with DVR.
•Check if the cable transmission distance is possible or optical
cable is compatible.
The LED is not on.
•Check the power and cable connection status.

Release Version 1.2
5
6. Specifications
Model No.
Transmitter
Receiver
Input
3G, HD-SDI, EX-SDI1.0
Optical
Output
Optical
3G, HD-SDI, EX-SDI1.0
Power Input
DC12V / AC24V
Current Consumption
DC12V 104mA /
AC24V 88mA
DC12V 87mA /
AC24V 77mA
Optical Fiber
Maximum
Transmission
Distance
Single mode fiber
EX-SDI 270Mbps : 20Km
Full HD 1.5Gbps : 20Km
Full HD 3Gbps: 20Km
Multi mode fiber
EX-SDI 270Mbps : 3Km
Full HD 1.5Gbps : 1Km
Full HD 3Gbps : 700m
Optical Fiber(Test fiber)
Multi mode fiber (MM50 / 125um OM3)
Single mode fiber (SM G.657B3)
Coaxial Transmission Standard
SMPTE 259M, SMPTE 292M, SMPTE 424M
Video Signal Bandwidth
270Mbps ~ 3Gbps
Optical Output Wavelength
at 1310 nm
Output Optical Power
-2 ~ -5 dBm
Receiving Sensitivity
Below -15 dBm
Connection
Port
SDI In/Output
BNC-F (75Ω)
Optical In/Output
LC Type
LED
SDI(s)
Red
ON : Input (TX)
Optical(S)
Red
ON : Input (RX)
Power(s)
Red
ON : Power Input On (TX, RX)
Temperature / Humidity
-10°C ~ +50°C / 0% ~80%
Case Material / Weight
PC / 32g
Dimension (mm)
MAIN : 73(W) x 23(H) x 20(D)
POWER : 19.7(W) x 40(H) x 19.9(D)
* Voice transmission is also available.
* Transmission distance may vary due to the specification of applied cable.

Release Version 1.2
6
7. Warranty Certificate
Product No.
Model No.
Date of Purchase
Place of Purchase
Purchaser
Name
Address &
Contact No.
Distributor
Name
Address &
Contact No.
Warranty Period
Two(2) years from the date of purchase
Any failure that occurs in the normal use for only two years after purchase will be
repaired free of charge.
Contact the phone number listed on the user’s manual for repair.
When reporting the failure, please inform the model name and condition of the
product accurately. It is convenient to know the name and department of the person
in charge.
Please check this user’s manual again before reporting the failure.
Product shapes and circuits are subject to change without notice to improve
performance.
Faults following will be treated as a charge:
•Failure by user’s handling without care
•Not connecting the rated power
•Disassembled or repaired arbitrarily by user
•When replacing consumables
•Failure caused by natural disaster(lightning, fire, flood, tsunami, etc.)

Release Version 1.2
7
S Se ee eE Ey ye es s C Co o. ., , L Lt td d
#
#5 50 03 3~ ~5 50 09 9, , 5 51 11 1~ ~5 51 12 2, , S Su un ni il l T Te ec ch hn no op pi ia a, , 5 55 55 5 D Du un nc ch ho on n- -d da ae er ro o, , J Ju un ng gw wo on n- -g gu u, ,
S
Se eo on ng gn na am m C Ci it ty y, , G Gy ye eo on ng gg gi i P Pr ro ov vi in nc ce e, , K Ko or re ea a ( (Z Zi ip p C Co od de e: : 1 13 32 21 15 5) )
T
TE EL L: : + +8 82 2- -( (0 0) )3 31 1- -7 73 30 0- -5 58 83 31 1/ /5 58 83 33 3
F
FA AX X: : + +8 82 2- -( (0 0) )3 31 1- -7 77 77 7- -3 35 51 12 2
E
EM MA AI IL L: : o ov ve er rs se ea as s@ @s ss sc cc ct tv v. .c co om m
h
ht tt tp p: :/ // /w ww ww w. .s ss sc cc ct tv v. .c co om m/ /e en ng g